The specific sequence of hemorrhagic spermatospermia in DP

When DP moves to the solo, it should be to buy the void first, and then decide what to buy according to the explosiveness of the opposite side.

When the burst is strong, for example, there are Nuker heroes such as TK Zeus on the opposite side.

You can buy 1200 balls first.

If you don't have it, you have to toughen the ball first.

Then the order of 1200 1100 1000.

Because what DP wants is survivability, not magic height.

If dp goes sideways.

There is no doubt that you should buy the ring first.

And then nothingness. It is not recommended to buy the ball directly when there is no nothingness.

There's no way to mix the lines that way.

This is not necessarily, it depends on the situation.

If you are against the wind, buy 1200 Essence Orbs first, then 1100 Vitality Orbs or Void Gems, and then ** ring the last 1000 Energy Orbs.

If you have a tailwind, buy the Void Gem first, then the ** ring, then 1200, 1100, 1000.

Toughen the ball first, and improve the recovery power is combat power. Next, essence balloons, firepower balls, and energy balls.

Buy 1200 plus blood and magic first, the most cost-effective, and a lot more blood in the early stage, it is not easy to die, and then out of the tenacity ball, confident in yourself first out of nothingness, otherwise first the ring, and then out of the blood stone and blue stone.

Great Tailwind first buys 875 Blood Ring and Void Gems, and then buys three balls.

Let's buy three balls for the headwind.

However, it is best to buy 1200 of them first, add blood and magic, and then buy back blood and nothingness, and finally synthesize.

It is recommended to start with 1200.

Then buy the ring, at 1100's.

Then nothingness. The last 1000.

Now you're 73, big brother, are you still living two years ago? . . The blood essence is already a dissuasion prop, and the blood essence is to mock the other party.

DP can be considered Blue Cat Don't consider it At present, many props are much higher than the blood essence.

To quote Rainbow's reply: Can the DP port download the hardware configurator? No!!! View the original post

Thank you for the trouble to adopt!

Mature follicles secrete a large amount of estrogen, which controls the hypothalamus to secrete FSH-RH on the one hand, and excites the hypothalamus to secrete LH-RH at the same time. Under the action of hypothalamic hormones, the ovaries undergo corresponding changes, which induce the ovulation of mature follicles. Under the action of pituitary hormones, the follicles after ovulation form a corpus luteum and secrete progesterone and estrogen into the body.

Large amounts of progesterone and estrogen induce the hypothalamus to release gn-rh, resulting in a decrease in gn. The corpus luteum loses gn and atrophies, and the sex hormones it produces decrease, and the endometrium loses its sex hormones and shrinks, necrosis, shedding, and bleeding, and menstruation comes. I don't know if you understand it or not, but that's probably it.

It's weird. Why are you looking for this?

If you're a girl. If you have your period, let's take a picture by yourself. I'll tell you if you're a boy.

Curiosity doesn't have to be. There's nothing to see.

//if(i==1) //dot=1;Put it in front, p0 7 can also be displayed.

p0=seg[wei[i]];However, immediately, it was erased by this article, if(i==1) dot=1; Put it in the back and show delay(2); At this point, you can observe for about 2 milliseconds so that when you put it behind, the person, can see it.

if in front: if i is equal to 1 dot is equal to 1 then run p0=seg[wei[i]];

If at the end: run p0=seg[wei[i]] first; Then determine if i is equal to 1 and dot is equal to 1

For example, if first: Stick the pulp first and then eat the fries.

If last): Eat the fries first and then the pulp.

The interface is different, and the function is the same.

Have you reconfigured your hardware? The module is added, the program is changed, and the configuration must be changed and re-entered.

The two biggest problems with the probability of SF lights being on are the mismatch between the data type and the data and the hardware configuration.

The program is executed automatically, and only the writer knows which pin controls the direction of the program.

Press DA to 10 and then press WRI (DA does not release at this time).

dp is after ag, but now there is a story of bw after dp.

Generally speaking, q and p have a functional relationship, and it is sufficient to find the derivative of q=q(p).

Otherwise, it usually tells you about elasticity, and you can just apply the elasticity formula.