What should I pay attention to when applying tiles? What do I need to pay attention to?

: You can choose tile caulk according to the color of the tiles in the kitchen, such as Dunlop's caulk series products, there are many colors of tile caulk. White tiles generally choose white tile caulk, dark tiles also have black tile caulk, and transparent tile caulk can be used to make mosaic parquet.

I chose white to match the off-white floor tiles, and any wine and oil stains on the floor can be wiped off. You see what color caulk you need, you can pick it yourself, this caulk is quite non-staining, recommended. Dunlop, a well-known brand of Ardex GmbH Group, as a leading manufacturer of building materials from Europe, provides you with a full range of solutions such as waterproofing, tile adhesives, caulks, substrate preparation, adhesives, etc

What should I pay attention to when applying tiles? What do I need to pay attention to? (1) Soak the tiles in water first. When pasting tiles, the cement should be placed a little full, and the amount of cement around the surface of the tile is about the same, so as to ensure that the tiles are firmly glued and will not be hollow.

2) After paving, use a special small hammer to hit the surface of the tile to detect whether it is hollow.

2. The tile must be flattened, and the experienced master will use a plastic hammer to beat the tile around to control the surface flatness of the tile in time. Otherwise, it will be too late to adjust the cement when it is dry.

3. The tiles are pasted vertically to ensure that all tiles are firmly sucked on the wall like a large piece of glass.

4. The tile must be glued firmly, after the tile is pasted, the outer edge of the tile and the wall are filled with cement, and the tile is also more firmly glued.

5. Pay attention to the 4 details of tiling.

Correct (1): If the decorator is experienced, the caulk of the tile and window frame is generally wiped with fingers. Because the brush is so soft, it is difficult for the caulk to get in completely.

Correct (2): The balcony should be tiled, so you need to brush a thick layer of mud on the original exterior wall, and the tiles will stick more firmly. If you don't paint, you can put the tile on it, but it will easily fall off.

Correct (3): Wall tiles are easy to crack, so it is quite difficult to drill holes in the tiles.

Correct (4): When tiles are to be pasted on the wooden wall, it is best to fix the barbed wire on the wooden board to increase the adhesion of the tiles. In order not to have to put tiles to do the trouble of repetitive work, I personally think that please be more professional.

The master sticker is better.

1. Before the tile is paved, it is necessary to spot check to see whether the grade, color difference and the sample are consistent, if it is confirmed, it is best to let the person in charge of the construction sign for it, otherwise the tile seller will be notified immediately.

2. If the wall is putty wall or calendered cement wall, it must be eradicated and roughened first. Wall tiles must not have less than 1 3 bricks.

3. The ground should be fully wet, and the horizontal line on the wall and the line on the ground should be prearranged to ensure that the low bricks of each room are on a uniform horizontal plane.

4. The floor tiles in the bathroom should have a slope of about 1% and about 10mm lower than the outside floor tiles.

5. After 1 hour of paving, the cement, caulk or other sticky objects left on the brick surface should be wiped clean in time, because it is more difficult to clean after four hours of caulk. After 12 hours of paving, the brick surface should be knocked on for inspection, and if there is a hollow drum sound, it should be re-laid. 24 hours after the completion of the brick paving, walk, scrub thoroughly, mix with clean water and detergent, and thoroughly clean the tiles.

As a professional decorator point of view, the early stage is to buy bricks to choose a good quality brick, before the tile to completely soak the tile, before the construction of the whole house need to lay the horizontal line of the whole house, to determine the horizontal position in the first place, so as to avoid the later because of the height difference and to see the door, the height of the balcony is higher than the customer, resulting in many of these problems can only be aesthetic or rework too much is very troublesome. If you lay a good horizontal line, you will know how high the cement mortar needs to be laid, and the room and living room and other spaces are at the same level. There is also the need to wet the wall when paving the wall tiles, so that the wall can fully absorb water and avoid the phenomenon of tile hollowing in the later stage; Now when pasting, the process of choosing a good brick, whether to use tile glue, new materials or copper wire grouting method is to be selected and compared.

To sum up, there are three points: one level, two bubble bricks, and three drenched walls. Most of the wall porcelain tiles or tiles are now glued with ceramic tiles, because they are not so thick and quite stable.

It is recommended to find a professional decoration company to give you integrated design and construction, so that the process and materials can be guaranteed, and worry-free, although it seems that the cost may be slightly higher, but the later after-sales tracking, construction do not have to run around, hard work.

1.If the floor tiles are paved, it should be noted that the sewer pipe should be ensured before the tiles are laid. Because the exposed sewer pipe will not only affect the appearance, but also make a loud sound when the water comes out, so it must be ensured before laying the tiles.

In order to reduce the sound of water discharge, the sewer pipe can be wrapped with soundproof cotton and then built with bricks.

2.If it is tiled in the kitchen and bathroom area, then you need to pay attention to the waterproof treatment. Moreover, the tile cannot absorb water after waterproofing, so it should be reinforced with tile adhesive when laying the tile, so that the tile will not fall off.

3.The order of paving tiles in home decoration is to first paste the wall and then the ground, first pave the interior and then pave the door, and after the paving is completed, it must wait for it to dry before stepping on it.

Recently, a friend asked Xiaolin, what should I pay attention to when tiling and paving? Xiao Lin specially asked the connoisseur, and the connoisseur summarized 4 points. I hope you take a good look and don't be fooled again.

Pay attention to the seams, the pattern, along the label, choose the appropriate cement label for paving, carefully read the relevant tile instructions before paving, soak the water for a long enough time, and do enough protection after pasting to avoid damage before use, a few words can say so much, in fact, you don't need to understand what to pay attention to, as long as you ask a good character, good technology of the old bricklayer, you don't have to worry about any problems with tiles.

Chuangrui assistant.

Tile is a very important step in the house, if it is not pasted well, it will cause hollowing and cracking, and there will be tile falling off after serious occupancy, which will cause safety accidents. Therefore, when decorating the house and tiling, you must pay attention to these details, keep an eye on these 4 places, no one can fool you!

1. When decorating the house and paving tiles, the ratio of cement and sand and gravel should be stirred, generally in accordance with the ratio of 1:3, otherwise the cement is easy to crack when the temperature changes abruptly, especially in the cold temperature in winter, the tiles on the surface will also bulge.

2. Before decorating the tile paving, it is necessary to pay attention to soaking in water, and the tile should be fully absorbed, so that the tile can be paved and the cement will be very firm, and the hollow drum will not fall off in the later stage.

3. After the decoration tiles are paved, the master will use a rubber mallet to beat the tiles, so that the tile cement is tighter without air and can avoid the deformation of the tiles.

4. When decorating and pasting tiles, it is best to use the whole brick set to cut the pipeline, switch, etc., and do not use the non-whole brick patchwork to pave.

5. In fact, no matter what the construction method is, if the waterproofing is not done well, it will leak, so the wall pressing the ground and the ground pressing the wall are not the key. Our construction practices are ground pressed walls, and ground pressed walls are good joints. The ground pressure wall must be pasted squarely, with a negative angle of 90 degrees, otherwise the floor tiles will be scrapped to cut the floor tiles.

6. When paving tiles in the kitchen and bathroom, the slope of the flowing water should be done, and the waterproof treatment should be done to avoid water accumulation, and the closed water test should be done for 12 hours or 24 hours to ensure that there is no leakage.

Nowadays, people's daily life is busy and stressful, and a warm home can bring everyone the most relaxing leisure time. But how do you make your home warm and comfortable? With a few tips, it's easy to create a pleasant home.

Personnel: 1-2 bricklayers are generally required.

Order: Paste wall tiles first, then floor tiles.

1. Paving colored glazed bricks:

Treatment of base layer, elastic line, tile immersion and wetting, paving cement mortar, installation of standard blocks, paving floor tiles, joints, cleaning, maintenance.

2. Paving ceramic mosaic tiles (mosaic) class:

Dealing with the base layer, elastic line, standard bar, paving cement mortar, paving, patting, sprinkling, unwrapping, jointing, grouting, cleaning, maintenance.

The construction points of paving ceramic floor tiles.

1. The concrete floor should be chiseled with a depth of 5 10 mm, and the spacing of the chisel marks is about 30 mm. After that, clean the floating ash, mortar, oil stains, and produce scattered water brush to the ground.

2. Before paving, the line should be played, and the reference line at right angles to the door entrance should be popped up on the ground, and the line should start from the door to ensure that the entrance is the whole brick, and the non-whole brick is placed in the dark corner or under the furniture, and the elastic line should be popped up to control the vertical and horizontal positioning.

3. Before paving the ceramic floor tiles, the ceramic floor tiles should be soaked and dried.

4. When paving, the cement mortar should be fully smeared on the back of the ceramic floor tiles, and the rubber should be compacted after paving. At the same time, check and correct with a level to wipe the cement mortar on the surface.

5. After 2 to 3 hours of paving, wipe the joints with white cement, and use cement mortar with cement and sand = 1:1 (volume ratio), and the joints should be filled densely, flat and smooth. Then wipe the surface with cotton silk, so that the purpose of cleanliness and waterproofing can be achieved.

Do you want to post it yourself? This person who buys tiles understands why not to ask them to post it is generally no problem.

Precautions when paving tiles The most important thing in house decoration is hard decoration, because if the soft decoration is not good, it can be replaced casually; However, if there is a problem with the hard installation, it needs to be dismantled and re-paved. The most important thing in hard decoration is the paving of ceramic tiles, so decoration owners must pay attention to the paving of tiles in the process of home decoration.

What are the precautions for laying tiles?

First, the tiles should be fully soaked.

Ceramic tiles should be fully soaked before paving, so that the pores in the tiles absorb water, so that it is not easy to appear hollow and fall off when paving, if the tiles are not soaked directly to the wall, it is very likely that the tiles will directly absorb the moisture in the cement, and when they reach a certain extent, the tiles will even have cracks, which will cause a lot of waste of tiles, and the quality of paving is not good.

2. Choose high-quality cement sand.

If the tile wants to have good paving quality, it is necessary to choose high-quality cement sand, so that the tile will stick tightly; The key point of choosing cement is to check whether it has QS certification, and to see whether it has passed the shelf life. It is best to choose river sand for sand, because river sand contains more moisture, and the effect of pasting will be better.

Third, the location of the first brick must be selected.

The position of the first tile determines the position of the tiles in the whole wall, so the position of the first tile must be selected, if the position of the first tile is wrong, the tiles of the whole wall will be crooked.

Fourth, we must make sure that the wall is pressed to the ground.

The wall pressing the ground is that the wall tiles should be on the floor tiles, the advantage of this is that there is no water, the water droplets in the wall will flow along the wall tiles to the surface of the floor tiles, easy to clean, because this is more troublesome, so some bricklayers find various reasons to be unwilling to do, this is the decoration owner must supervise the bricklayers, let them do the project well.

Fifth, it is best to place the cut tiles in the corner of the wall.

Cutting tiles will always look a little uneven, so it is best to cut tiles in the corner of the wall, which can be sealed with sealant at the end and will not affect the decoration effect of the house. If it is placed in a conspicuous place such as under a window, it will affect the aesthetics of the house.

The following issues are mainly considered for tiling. One of them is the empty drum rate. Second, terracotta tiles need to be soaked with water. All-porcelain is not used. Third. Exhaust pipes and other small flowers need to be returned to the square. Fourth, the floor of the bathroom is pasted with tiles, pay attention to the slope of the water.

Other students must pay attention to the following points when pasting tiles: It is best to be able to be on the spot Part of the not too perfect tiles can be pasted by workers in some invisible positions in the future, such as cabinets, washbasins, mirrors, etc., and pay attention to the tiles, waist bricks, etc. Before pasting wall tiles and floor tiles, the soaking time must be enough.

Be sure to plug the floor drain with things to prevent the cement from falling and clogging. The floor drain in my house was blocked because of the drop of cement, and it took 30 doors to find the management office to dredge it, and a lot of small mud blocks were raised. People are on site, and workers don't waste tiles too much.

My family was not on the scene when the tiles were pasted, and when I went to see it, I was wasting a lot of bricks, which was very heart-wrenching, and it was all sweat and sweat.

1.The ratio of mud cement and mortar for tiling is not as high as possible, and the ground is relatively small, but if the proportion on the wall is too large, the wall itself may be cracked after pulling when the wall itself is moved in the later stage.

2.The ground is leveled or sloped, and the wall is tiled vertically.

3.Butt joint treatment when tiling.

4.The touching angle of the yin and yang corner place.

5.After the tiling is completed, according to the temperature, it will be placed for 24 to 48 hours, and after drying, use the key to scrape along each row, and detect whether there is a hollow drum through different sounds, that is, the mortar cement under the brick is not compacted. In general, wall tiles have a hollow drum rate of 3% to 5%, and floor tiles < 3%.

6.For antique bricks, or special needs when paving need to leave the seam treatment, also need to use the cross card to fix the seam distance when tiling.