What is the reason for the deviation of the direction of the Magotan car

There are many reasons such as birth defects, suspension deformation due to impact, difference in left and right tire pressure, or difference in tire wear, it is recommended to adjust the left and right wheelsets. In short, find a place to do four-wheel alignment professionally and check it out!

The toe-in is not correct and requires four-wheel alignment. It will eat tires for a long time, so hurry up and locate it.

First of all, change the tires left and right, and if you still run in the same direction, do four-wheel alignment.

Fetal eating. You can do a wheel alignment.

The measures to solve the deviation of automobile tires are as follows: 1. Test tire pressure From the actual situation, the most common factor that causes the car to deviate is the deviation caused by the different tire pressure. This is very simple, go to the maintenance agency to measure the tire pressure, to ensure that the tire pressure is consistent, you can solve the problem.

In addition to tire pressure, varying degrees of tread wear can also cause mistracking, which is where it is necessary to change the tire position or replace the tire. 2, four-wheel alignment This measure is also the most common way to correct the deviation, compared with the tire pressure, the cost of four-wheel alignment is higher, the owner can first see the effect after balancing the tire pressure, such as still running off, four-wheel alignment or have to do. 3. Check the suspension If the four-wheel alignment does not work, you should consider whether the suspension of the vehicle is a problem.

Generally speaking, if there is a problem with the design of a car's suspension, it is easy to deviate. In addition, in the process of use, suspension injury, deformation, displacement, etc. are prone to deviation. 4. Check the steering The steering system may be worn for a long time, so that the gap of the connecting parts is too large, or the bearings and other components are loose, resulting in the car can not drive according to the normal trajectory, resulting in deviation.

5. Replace the spring on both sides If it is because of the deviation caused by suspension, the owner must replace the left and right sides together when replacing the spring, rather than only replacing the spring with unilateral problems, so as to ensure that there is no new deviation.

The possible reasons are: 1. The four-wheel alignment parameters are incorrect, you can go to the 4S shop to do the four-wheel alignment 2, the left and right tire pressure is inconsistent, you can pump 3, if the tire is abnormally worn, the lower swing arm is deformed, the front and rear axles are deformed, the left and right tire patterns are inconsistent, the size of the tire or steel rim is inconsistent, etc. You can go to a 4S shop to change the tire.

Specifically:1Tire pressure is unbalanced.

The imbalance of tire pressure on both sides of the vehicle will directly lead to the deviation of the vehicle! The principle is very simple, the tire pressure on both sides is unbalanced, on a flat road, the left and right are high and low, and the vehicle will naturally deviate to the side of the gas loss.

Solution: It is recommended to check whether the tire pressure on both sides is normal, and if there is a loss of air, then pump and fill.

2.Wheel alignment.

For vehicles that have been driven for a period of time, changes in wheel alignment data can also lead to mistracking. Especially for vehicles that often walk on potholes and on and off the road, the parameters of four-wheel alignment are more likely to change.

Solution: Find a time to go to the 4S store to do a four-wheel alignment, most of the deviation is caused by inaccurate positioning.

3.The wheelbase on the left and right sides is inconsistent.

Wheelbase is the distance between the two perpendiculars that pass through the center of two adjacent wheels on the same side of the vehicle and are perpendicular to the longitudinal plane of symmetry of the vehicle. To put it simply, it is the distance from the center of the front axle to the center of the rear axle of the car. As shown in Fig-2, a is the wheelbase of the car.

If the body is deformed greatly, and it is not corrected in time, or it does not meet the technical requirements after correction, it will lead to the inconsistency of the left and right wheelbases, and the load-bearing body of the car is more prominent. When a car is moving, it is deflected towards the side with a shorter wheelbase.

Solution: First of all, check the wheelbase on both sides with a four-wheel aligner, if the wheelbase difference does not meet the technical requirements, the body corrector can be used to restore the deformation. When making a preliminary judgment, you can also use a meter ruler to measure at the center of the wheel.

4.Chassis problems.

Mistracking can also be caused by changes in the main components of the chassis, which can be due to wear and tear caused by daily driving, or due to frame deformation caused by accidents. If there is a change in components such as the lower swing arm or the gap is too large, adjusting or replacing the parts can be solved; If it is caused by the deformation of the car body and the damage to the frame caused by the accident, it is more serious, and it is necessary to replace parts in a large area or even to correct the frame before it can be fully recovered. The reasons for the deviation of the driving direction are:

1. Excessive wear of one side of the tire; 2. The shock absorption of the ball head is damaged; 3. The tire pressure on both sides of the vehicle is inconsistent; 4. The relevant parts of the vehicle suspension system are deformed or the working performance is poor. The impact of deviation in the driving direction is: at least it will cause tire gnawing and tire scrapping, and at worst it will cause tire bursts and the occurrence of dangerous situations of vehicle out of control.

Deviation in driving direction refers to the phenomenon that the car deviates to one side by itself in the process of driving in a straight line on a flat road, resulting in the inconsistency between the center line of the front and rear axles and the center line of the driving trajectory.

1. Tire pressure is unequal.

If the left and right tire pressures are unequal, it will cause the wear and tear of the drive wheels and the ground to be different, and different friction will directly cause deviation. The solution is to go to the car maintenance shop to check the tire pressure.

2. Suspension system failure.

Suspension system failures can also cause the car to mistrack, such as suspension injuries, deformation, displacement, and other ......There will be deviation, such a problem is more serious, once the problem is found, try to do a repair.

3. The wheelbase on the left and right sides is inconsistent.

After a long period of use, the vehicle will inevitably encounter bumps and bumps. When the overall deformation of the vehicle, the difference between the wheelbases on both sides is too large, and it is not corrected in time, or the correction does not meet the technical requirements, when the car is driving, the vehicle will deviate to the side with a short wheelbase.

According to the survey, for ordinary family cars, the probability of surviving a puncture at 150km h is less than 20%; Although deviation is not a problem that can make the car break down immediately, there are still many hidden dangers in long-term driving deviation of the vehicle, once found, you should immediately go to a professional maintenance station for a comprehensive inspection.

If the vehicle only deviates slightly to the right, then considering the road design, it is difficult for us to notice with the naked eye, in fact, in a flat ordinary road, it is high in the middle and low on both sides, this is because it is necessary to reduce the accumulation of water in the rain. Of course, it is not necessary that both sides of the road are lower than the middle, for example, where the turn is made, the outside must be higher than the inside, which is to prevent the car from being affected by centrifugal force.

The deviation of the car may be due to the unequal air pressure of the tires on both sides.

Different tire pressure will make the tire become different size, and it will inevitably deviate when driving.

Or the deformation cushioning on both sides of the front shock absorber spring is inconsistent.

The quality of the shock absorber spring can be judged by pressing or disassembling and comparing.

The direction of the car has been deviated to consider whether there is a problem with the steering wheel, for us unprofessional personnel can not give a definite answer, consider going to the repair shop to check it formally.

The most direct way to adjust the steering wheel is to adjust the steering wheel is Sixian Chang wheel positioning, but now many car owners want to do it themselves, so let's take a look at the way to adjust the steering wheel by yourself. Note that there is a certain risk in doing it yourself, and the risk is that there is no change or more serious impact after adjustment, so please choose carefully.

First of all, we must be clear that this adjustment is the steering lever, which is an important part of the steering mechanism of the car, which directly affects the stability of the car operation, the safety of operation, and the service life of the tire. As shown in the figure, if the steering lever is long on one side and short on the other, it will cause the car to deviate to the longer side.

Adjusting the length of the steering rod does not require us to "cut shorten" or "extend", but to "screw in" or "spin out" the base of the lever. Start by preparing the wrench, then knock the steering wheel of the vehicle to the right to expose the rear of the left front wheel. As shown in the figure, first loosen the fastening nut with a wrench, and then rotate the left tie rod clockwise, clockwise is the position of the tie rod relative to the base of the tie rod, and the left tie rod "screw" is shortened.

Then repeat the previous steps and knock the steering wheel to the left to expose the back of the right front wheel. Similarly, first loosen the fastening nut with a wrench, and then rotate the right tie rod counterclockwise, and the right tie rod "unscrewed" is elongated.

If the vehicle is only slightly deviated to the right, then take into account the road design factors, but if the direction of the car deviates severely, then the car mainly checks the tire pressure, if the tire pressure on both sides of the car is unbalanced, then driving on a flat road, the natural wheels will deviate to the side of the loss.

The vehicle should change the position of the tires regularly, because the driving wheels will wear more than other wheels, and if left unchecked, the car will also deviate. In addition, the inconsistent wear of the tire pattern on both sides will also cause the car to deviate.

The direction of the car deviates, and many car owners immediately think of doing four-wheel alignment. Changes in four-wheel alignment data can lead to deviations, especially for vehicles that often walk on potholes, and the parameters of four-wheel alignment are easy to change. The direction deviation of the car is mainly related to the camber angle of the front wheels, if the camber angle of both wheels is not consistent, then the car will deviate to the side with a large camber angle.

In addition, if the steering system of the car is abnormal, it will also cause the direction to deviate. For example, the knuckle arm and knuckle are bent and deformed, which generally causes the car to deviate in one direction. The most serious thing is that the ball head of the horizontal tie rod ruler is severely worn and loose, which will cause steering failure, and the car will be completely out of control.

Photo by Zou Ting1) @2019

If the vehicle deviates only slightly to the right, then the road design is considered, but if the vehicle deviates severely, then the vehicle mainly checks the tire pressure at this age. If the tire pressure on both sides of the vehicle is unbalanced, then when driving on a flat road, the natural wheels will be biased towards the side that suffers from gas loss.

The position of the tires should be changed regularly, as the drive wheels will wear out more than the other wheels, and if left unchecked, it will lead to deviations in the direction of the vehicle. In addition, inconsistent wear of the tire pattern on both sides can also cause the car's orientation to deviate.

The direction of the car is deviated, and many car owners think of doing four-wheel pick-up positioning for the first time. Changes in four-wheel alignment data can lead to deviations, especially for vehicles that often walk on bumpy roads, and the parameters of four-wheel alignment are prone to change. The directional deviation of the car is mainly related to the camber of the front wheels.

If the camber of the wheels on both sides is not consistent, then the car will be biased to the side with a higher camber.

In addition, if the steering system of the car is abnormal, there will also be a deviation in direction. For example, the bending deformation of the knuckle arm and knuckle will generally cause one-way deviation of the car. The most serious problem is that the tie rod ball joint can come loose after severe wear, causing the steering to fail, which in turn can cause the car to lose control completely.

Millions of car purchase subsidies.

What are the reasons for the deviation in the direction of FAW-Volkswagen's speed: 1. The road conditions are uneven, and the flat ordinary highway design is high in the middle and low on both sides; 2. The tire pressure is inconsistent, and the tire pressure on both sides is unbalanced, and the road conditions are uneven; 3. The tire wear is uneven, the vehicle should regularly change the position of the tire, the wear of the driving wheel will be greater than that of other wheels, and the inconsistent tire pattern on both sides will also cause the direction of the car to deviate; 4. The parts of the chassis suspension system are damaged, such as the steering knuckle arm, the steering knuckle is bent and deformed, the shock absorber is deformed, and the ball joint of the swing arm is loose; 5. The mileage is too long, and the poor road conditions lead to changes in tire positioning parameters; 6. The accident repair parameters are unqualified, the wheelbase length on both sides is inconsistent, the wheelbase difference between the two sides is too large, and it has not been corrected in time, or it does not meet the technical requirements after correction.

How to adjust the steering wheel when it is not straight or slightly off? How to adjust the steering wheel of Sutar, you can do a four-wheel alignment.

When the vehicle is used for a long time, when the user finds that the steering wheel is heavy, shaky, off track, incorrect, misaligned, or abnormal wear such as unilateral wear, wavy wear, block wear, eccentric wear, etc. , and while driving, the vehicle feels floating, jolting, swaying, etc. , he should consider checking the wheel alignment value to see if there is too much deviation and repair it in time.

The left and right sides of the quad wheel alignment are:

1.increase driving safety;

2.Reduced tire wear;

3.Keep the steering wheel upright when going straight and keep going straight;

4.The steering wheel automatically corrects after steering;

5.Increases the sense of driving and handling;

6.Reduced combustion consumption;

7.Reduce wear and tear on suspension components;

Hold the steering wheel with your left hand and shake it gently, while your right hand shakes the key to unlock it. The reason why the steering wheel is locked is a very basic anti-theft function of the car. The principle is that the steel pin is controlled by a spring through the rotation of the key.

When the key is pulled, as soon as the steering wheel is turned, the steel pin will bounce into the pre-reserved hole and then jam.

The reason why the steering wheel of a car is locked is mostly because we accidentally touched the steering wheel when we pulled out the key and touched the automatic safety locking device. At this point, the car's security system locks the steering wheel. In this case, we just have to insert the key, turn the steering wheel in the opposite direction and at the same time twist the key and the car can be easily started.

For some keyless start cars, when we start the car, don't step on the brakes, press the keyless start button first, then turn the steering wheel, step on the brakes, and then press the start button above, so that the car can start successfully.

Millions of car purchase subsidies.