Why does my automatic winding machine reset but the spindle can t flip?

The spindle can't be flipped? The spindle is rotated and cannot be flipped, and the mechanism that can be flipped has a guide pin mechanism and a surplus clamp mechanism. These 2 mechanisms are generally achieved by controlling the rotary cylinder through a solenoid valve, and you can find the solenoid valve.

Find the solenoid valve that controls these 2 cylinders, and let you manually press the small metal button on it to see if there is a response? If you don't change the solenoid valve. If it can't be solved, **:

31635948。Let's solve it together.

The flipping of the winding spindle depends on whether the control part has such a function, and not all automatic winding machines can be reset.

Magnetic transmission of spindle status? Cylinder with spindle action Pneumatic motor? Solenoid valves? Tracheal poor contact? Incorrect instruction?

After the reset is successful, the reset light is on before the reset is completed. If the start button is pressed and the reset light is still on, it means that the start button is broken and it must be replaced or repaired. If the button is not broken, check the program and judge which step it stops at.

The emergency stop switch is pressed, and it is not complicated.

It is recommended that you give the manufacturer, they are more professional, or go to other professional manufacturers to ask.

When the machine is turned on, the controller needs to perform the origin check action, first of all, the origin of the cable lever is checked, and the cable bar moves to the direction of the origin sensor after starting, and then locates to the starting point after sensing ("automatic positioning" needs to be set in the program) zero point; Then the spindle is rotated to the zero position (the check absolute counting method is set internally) If the relative counting method is set, the spindle will not be positioned and rotated.

After that, the controller will be displayed as standby, indicating that the self-test has been completed.

Normal: If there is an error in booting, an error will be displayed**,err-?。 Please check it out and ask a follow-up question.

To give you a common sense, people in the entire winding machine industry have tried to do one thing, that is, to wind the coil neatly, and it is not messy to a wire, but there are many aspects of whether this is neat or not, because of the mechanical precision of the winding machine, the algorithm, and the accuracy of the enameled wire, the accuracy of the skeleton, the structure of the skeleton and so on.

If it is an automatic winding machine, the wiring device is not adjusted well. If it is a manual arrangement, it has not undergone basic training.

It may also be related to the accuracy of the winding machine.

The automatic winding machine is suitable for products with large batches, if the product batch is small, the specifications are not applicable, which is a more obvious shortcoming.

The level of automatic control technology is not up to the level of precision.

The investment cost of automation equipment is high.

1. The process of trial operation must be started by a skilled operator.

2. Before the trial operation, check the fastening of each connection and installation, the lubrication point, the sealing place, and the condition of the heating and drying mechanism.

3. Check whether the transmission belt and screw rod are normal, and whether the actuator driven by each motor is in a normal position.

4. You can use your hands to slowly push or rotate the wheel belt to reset it to normal. After the components are guaranteed to be normal, the trial operation can be carried out.

5. Before turning on the machine, turn on the power switch and the computer power switch. First of all, find the motor start position on the man-machine interface, start the motor, and then press the reset button, you can press the start button on the right side of the machine, and the equipment will run.

6. Press the stop button to stop the operation. The reset button is used to restore each executor to its original position.

7. If there is a situation in the middle of the way, there is a power switch and a computer power switch on the right side of the man-machine interface board, press the power switch button to cut off the power supply, or press the emergency stop button.

The width is the total width of the coil you are wrapping.

The wire diameter is the diameter of the enameled wire, but the wire diameter set in the actual winding process is slightly larger than the actual wire diameter.

The part number is stored in the "starting step" and "knot step".

With the rapid development of science and technology, the difficulty of setting up and debugging the modern automatic winding machine has greatly increased due to the integration of many technologies such as electrical control, mechanical transmission, photoelectric detection, etc

For the Xiep winding machine, the manual of the electronic file of the manufacturer is more detailed.

Just follow the steps on the manual to debug the winding machine.

There are two general situations, one is that your spool may be abnormally unsmooth, and the other is whether any of the four wires of your stepper motor are not in good contact.

Changing the reset sensor will do the trick.

Our company's newly developed magnetic ring automatic magnetic winding machine can wind thick wires without manual labor.

There are many reasons why you can't spare the thick wire, such as your wire reel does not support the wire pin If the equipment fully has the size of the wire warp, it is because your thick wire is too hard, and the wire wheel cannot pull the wire.

There are three types of winding methods for magnetic wire winding machine: one is the side slip type, which can only wind the thin wire (below), the other is the belt type, which winds the conventional wire diameter (below), and the other is the gear type, which can be wound with thick wires (the above can be used).

I can't stand the pull, I don't really understand it.

There is the enameled wire which I was not able to wind.

How big is the line? Thick lines are okay!

You mean it's fully automatic.

As long as it is not enough in the magnetic ring, the following lines are not a big problem.

Web Links.