Epson R350 is a good way to clean the nozzle every time it is turned on after changing the supply?

If you can print every day, it's worth it, but the failure rate is also very high. If it is for home use, don't change it to supply if the print volume is small, it is easy to plug the head. And some people say that after being modified into a continuous supply system, it is easy to reduce the life of the print head, which is quite terrible, and the manufacturer does not support maintenance after the printer is modified to continuous supply.

If you have a lot of printing needs, you can consider the HP Super Macrifuga inkjet printer series, which uses lower cost, higher capacity ink cartridges, and most importantly, the quality of the print is very good. The printer also has a lot of money to buy, and who wouldn't want to use it for two more years!

There are many problems to pay attention to when using continuous supply, the most basic is to buy a good point for continuous supply, ink quality to pass, now ink in many places is a hammer deal, make people panic, now many manufacturers are hated by these garbage manufacturers, hehe, if you say that every time you turn on the clean, you try to reinstall the printer to see.

Is it automatically cleaned every time the machine is turned on? If yes, I can only say I'm sorry I didn't bother with this problem, has the driver been reinstalled?

Or will you not have to plug your head for a few days?

It is possible that the ink you are using is relatively large.

It doesn't matter if the printer door cover sensor is there, you can detect that the door is not closed and the print head walks back and forth. This results in automatic cleaning.

Hehe, because I didn't trim this machine, the inkjet machine can be said to have not been repaired much, at most just add water.

So if there is something wrong, please bring it up.

If you change to a better continuous supply, it may be that your continuous supply of air intake is not good.

There's no way, it's like that.

How to disassemble the Epson R330 nozzle:

1. Move the ink cart to the position where the ink is replaced;

2. Facing the ink car, on the left side of the ink car, there are three bamboo shoots directly above, and they are vigorously pressed down; After pressing down, the outer baffle on the left side of the ink cart can be removed;

3. Looking at the inside of the ink car, at the bottom, near the bottom, there is an L-shaped plate; First, press down with your right hand, push to the right, and then use your left hand to open the bamboo shoot stuck on the left side of the ink cart.

4. Remove the three screws in the ink car;

5. Pull the nozzle up directly.

First, move the ink cart to the position where the ink is replaced;

Facing the ink car, on the left side of the ink car, there are three bamboo shoots directly above, and they are vigorously pressed down; After pressing down, the outer baffle on the left side of the ink cart can be removed;

Looking inside the ink car, at the bottom, near the bottom, there is an L-shaped plate; First, press down with your right hand, push to the right, and then use your left hand to open the bamboo shoot stuck on the left side of the ink cart.

Remove the three screws in the ink car;

Pull the sprinkler up directly.

First, move the ink car banquet to the position where the ink is changed;

On the left side of the ink car, there are three bamboo shoots directly above, which are vigorously pressed down; After pressing down, the outer baffle on the left side of the ink cart can be removed;

Looking inside the ink car, at the bottom, near the bottom, there is an L-shaped plate; First, press down with your right hand, push to the right, and then use your left hand to open the bamboo shoot stuck on the left side of the ink cart.

Remove the three screws in the ink car;

Pull the sprinkler up directly.

After sending the print command, the printer can feed the paper normally and the printing action is normal, and the blank page or white horizontal stripe is printed at this time, which is caused by the nozzle is blocked, please refer to the following solutions:

1.If you are installing a newly purchased ink cartridge, you can see a yellow adhesive strip on the ink cartridge when you open the inner and outer packaging, and you must remove this seal before replacing the ink cartridge before installing it on the printer.

2.Follow the method below for nozzle inspection:

1) Turn on the printer and load A4 paper in the printer feeder;

For Windows 98 Me users).

Select "Start" - > Settings - > Printer", right-click the printer icon, and select "Properties" - >Maintenance" or "Utilities";

For Windows 2000 XP Vista 7 users).

Select "Start" - "Control Panel" - "Devices and Printers" or "Printers & Fax", right-click the printer icon, and select "Printing Preferences" - "Maintenance" or "Application Tools";

3) Select "Nozzle Check", select "Print" according to the on-screen prompts, and the printer will print out the nozzle check sample;

4) If the printed nozzle inspection pattern is missing color or broken line, please select the "Print Head Cleaning" button;

5) It is recommended to leave the print head for 24 hours to fully soak the ink into the print head and then do a nozzle check to avoid wasting the ink;

6) After 24 hours, please do 2 more times to clean the print head, if it still doesn't work, you need to contact the Epson authorized service center to professionally clean the printer, you can browse the following ** to view the nearest service center:

There are two ways to clean the printhead.

1 is the inside of the printer driver cleaning method is as follows.

Click Start in the bottom left corner of your computer, double-click Printers & Fax--- select your machine model--- right-click on Printer Preferences--- Maintenance --- Printhead Cleaning.

2 is to remove it and clean it.

After removing it, put it in ultrasound and soak it in the through-head solution diluted with warm water, depending on the soaking time, you can use a syringe to pour water from the top of the print head to check it, and then dry it with a hair dryer, leave it for 24 hours, and then put it on the machine to prevent burning.

But I advise myself not to try the second method, because if the printhead is really blocked, the chance of clearing it is very small.

Control Panel--- Printer & Fax--- Epson your machine model--- right-click on "Printer Preferences" - Maintenance --- Printhead Cleaning.

You can use anhydrous alcohol, if the head is blocked, soak the surface with hot boiling water, and do not soak the circuit plate on the ink cartridge.

It is best to use the cleaning program of the machine belt, and the above method is done only when necessary, good luck.

Start by printing the nozzle pattern to determine if it's the printhead reading, or if there's too much air inside the cartridge. Because these two completely different faults show the same phenomenon: printing horizontal lines, or color casts.

Before and after cleaning the nozzle, print the nozzle check pattern separately (check pattern, print).

If the disconnection position is fixed, the nozzle is blocked. Printer properties, maintenance, printhead cleaning, 3-4 times, usually you can print normally. If it doesn't work, you can't continue cleaning. Because the nozzle is cleaned many times in a row, there is a risk of burning out the nozzle.

Do not use the syringe to pressurize the nozzle, otherwise it is easy to break through the nozzle cavity and cause the nozzle to be scrapped. Do not disassemble the sprinkler head for soaking, which is also very dangerous for the sprinkler to operate. It is recommended to use the no-dismantling method to clean the printhead manually, which is the safest and most effective method.

If there is a change in the position of the broken wire before and after cleaning, it is because there is too much air in the inner cartridge, not because the nozzle is blocked. In this case, it is dangerous to clean the nozzle. It is recommended to use a safe exhaust method to drain excess air from the inner cartridge.

Safe exhaust, no ink cartridge insertion, no use of any tools, so it is the safest and most effective for the printer.

Double-click on the computer on the desktop, then locate and click Control Panel on the page. 2.Once in the Control Panel, find and click on the "View Devices and Printers" button in the Control Panel.

3.Right-click the printer whose printhead you want to clean, and then click "Printer Properties" in the pop-up option box. 4.

Click the Maintenance button on the pop-up page, and then click the Printhead Cleaning command on the Maintenance page. 5.Finally, click the start button, and after cleaning, you can click to print the test paper to see the effect.

Questions. The XP-245 blue nozzle is a little blocked, and it still doesn't work to rinse four or five times, how to clean it with cleaning solution?

Teacher, send a tutorial.

The nozzle should not be cleaned more than 3 times. If 3 consecutive cleanings are ineffective, do not continue to clean. Because the power cleaning nozzle not only accelerates the aging of the nozzle, but also has the danger of burning out the nozzle.

You can use the program that comes with the above printer to clean it.

On the body, use a syringe to drain the ink from the ink cartridge, inject a special nozzle cleaning solution, and use the printer's own program to clean it.

Questions. How to operate the external cartridge, please guide!

If you need to clean the sponge inside the ink cartridge, heat the cleaning solution to 60°C, pour it into the sponge, let the cleaning solution melt the agglomerated ink inside, use it with the printer nozzle cleaner, and then pump out the ink that has melted the cleaning solution or spin it dry with a centrifuge.