What glue can be used to stick sunscreen aluminum film and glass

Tang Sanzang traveled westward, and when he left the border, he fell into the demon cave, and was rescued by Tai Bai Xing. encountered a tiger in the Two Realms Mountain, fortunately rescued by Liu Boqin, and then recited the longitude to Liu Boqin's father's superbirth. In the Five Elements Mountain, remove the pressure post of Rulai, rescue Sun Wukong, and give the number of the walker.

Because Sun Wukong killed the robbers who robbed the scriptures, Tang Seng fell into a few people, Sun Wukong left in a rage, Guanyin turned into an old mother, and passed a golden flower hat to Tang Seng, a tight mantra, deceived Wukong into wearing a golden flower hat, and the golden hoop was embedded in the flesh. Tang Seng recited the incantation, and Wukong had an unbearable headache, which was used as a means for Tang Seng to restrain Wukong. [3]

Summary. It's put inside.

It's put inside.

1.Stickers are more common insideUsually, most friends only consider the inside of the window when choosing a heat insulation film, and do not think about putting a layer of window film on the outside of the window. Because they believe that the main purpose of window film is to make the interior more comfortable, and it is only right to stick it on the inside of the window.

Therefore, it is more common for insulated window film to be attached to it. Because 2There are also some people who believe that sunlight and heat are shining in from the outside, and if you want to make the interior cooler, you can stick the window film outside to isolate more sunlight.

Therefore, there are also many people who will stick the window film on the outside when they are late. However, it should be noted that the window film attached to the outer layer of the window is usually exposed to the wind and sun, and needs to have sunscreen and waterproof properties. In other words, the insulating film attached to the outside of the window needs to be a special film.

3.Of course, some people believe that if you want to maximize the thermal insulation effect, you can paste the heat insulation film on the outer and inner layers of the window. This is also a desirable way, but window renovation is more expensive, and you can do it if you have a sufficient budget.

4.Tips for pasting insulating window filmWhen pasting window insulating film, in addition to figuring out whether the window film is pasted on the outside or inside, it is also necessary to understand some tips for sticking the film. For example, the cut heat insulation film is about 1-2cm larger than the window glass; There are two layers of heat insulation film, the outer transparent is the protective film, and the color is the film, and the protective film should be torn off before use; Scrape the water in the 4-minute direction to ensure that the film does not blister.

The method of applying the sunscreen film is as follows:

1. Before the film, first of all, we must ensure that the working environment meets the requirements of dryness and less dust, otherwise the dust and debris will enter during work, which will affect the effect of the film. It is recommended to wash the car before applying the film;

2. Cover the necessary position of the vehicle, protect the interior and exterior with a protective cover, if there is no special material, you can also choose plastic wrap;

3. Clean the car glass that needs to be filmed, pay attention to the top and edge of the glass, and then wipe the water;

4. The next step is to cut the car film, pay attention to the size of the car film to match the glass. Spray a little water on the surface of the glass, then adsorb a certain thickness of plastic film on the car window, and then draw a template according to the edge, the template is a little more than the glass;

5. When the front and rear windshields are filmed, the baking film also needs to be shaped. Cover the cut film on the outside of the glass, and then use the heat gun to shape it, which is also a key step to bury and is prone to mistakes, because the temperature and shaping method of the heat gun have relatively high requirements, otherwise improper use can easily lead to blackening of the car film or glass breakage;

6. After the baking film is completed, you can officially paste the film, spray the inner glass with clear rough water or window film installation liquid, and then tear off the innermost layer of plastic film from the car film, and then paste the car film on the inner glass and move it to the most suitable position;

7. Spray some water or window film installation liquid on the surface of the car film, and then use the Yangtze River Delta plastic scraper to catch the water.

8. After the water is completed, check whether there are bubbles between the car film and the glass, whether it is firmly pasted, whether there are wrinkles, whether there are scratches, etc., if there is no problem, finally clean the water on the edge of the glass with a towel.

Millions of car purchase subsidies.

It is best to work with two people, taking care to straighten vigorously to prevent wrinkles, blistering, etc.