How to remove the glue from the car film?

The removal of the car film requires certain skills, and the specific steps are mainly as follows:

1. Peel off the film. The first thing to do is to lift the corner of the car film, it is recommended to use a fingernail or tape to glue it, if not, then consider using a blade to peel it off.

2. Tear off the film. With the hot air of a hot air blower or hair dryer, use appropriate force and speed to slowly remove the car wrap.

3. Remove glue. If there is any residual glass film glue after tearing, clean it with adhesive remover or cleaning agent.

4. Ventilation and drying. After the glass film is torn, there will be some glue odor, which can be removed by ventilation and drying.

After the car film is torn off, there may be some film glue left on the car glass, which should be removed in time to avoid affecting the effect of replacing the new film. How to remove the glue after the car film is torn off? This requires a professional tool to remove the glue with a deglue remover or cleaning solution.

However, extra care needs to be taken when using a glue removal knife to avoid scratching the glass. If you don't have a glue remover or cleaning solution, you can also use alcohol or wind oil, both of which can soften the adhesive and make it easier to remove.

If you want to better remove the car film, it is best to choose a high-quality car film when buying and installing the car film, and go to a professional car beauty shop for installation, which can reduce the risk of the film and make it more worry-free.

There is a special adhesive remover, which can be wiped off by spraying, or you can use |The hair dryer blows the heat and wipes it off, but it is more troublesome to connect the electricity.

It can be dried with a hair dryer to soften, which is also a good way to remove glue traces.

2. You can also wipe it with a cotton swab dipped in nail polish remover.

3. A good way to remove glue traces can be wiped with wind oil essence.

4. Use a special detergent or sneaker detergent to wipe it.

5. The 4B eraser we use for drawing is a very soft kind of Korean eraser that can be erased.

6. If the traces that have been left for a long time have hardened, you can use a hot towel to soften it before trying, which is also a good way to remove the traces of glue.

7. Use soap and a little ammonia and turpentine to mix liquid, which can remove a lot of dirt and make the glass surface more shiny (this article is applicable to ceramic tiles, ceramics, glass, etc.).

8. Repeatedly stick and tear with transparent adhesive with good viscosity, which can remove some of the surface, which is one of the good ways to remove glue traces.

Precautions. In fact, before removing the logo sticker on the front windshield, you can first cover it with a hot towel to soak the car logo, and when it is soaked, some logo stickers can be easily removed. Some car owners said, "When encountering a long-term and strong adhesion sticker, if the front windshield is not pasted with solar film, you can use a special cleaning solution to remove it, such as asphalt cleaner."

If you don't have these removers, you can also soak them in soapy water or laundry detergent water, which can also achieve a complete removal effect. ”

If the front windshield is covered with solar film, you can use a towel dipped in a small amount of alcohol to wipe the car logo repeatedly, but never spray it directly on the glass, otherwise it will damage the car film. Whether the front windshield is pasted with or without a sun film, you can't use sharp tools such as blades to remove the logo sticker, otherwise it will scratch the glass or sun film, and all kinds of bank cards, membership cards, and ** cards are good tools.

It is recommended to go to a professional film construction shop to remove, if you do it yourself, the whole vehicle is not finished in half a day, and there is trouble if you can't get the glass to get flowers.

The film shop charges two or three hundred for the whole vehicle, and if you stick the film in them, you may get it for free. It's too troublesome to get it yourself, you need the best blade for filming, you need good knife work, and you need physical patience.

It is advisable not to make it yourself. If it is a small area, you can get it yourself, mix it with water and dish soap, spray it at the position where you want to remove the glue, and then scrape it with a blade, the angle of the blade should be mastered, about 30 degrees to 45 degrees, otherwise it is easy to scrape the glass, and you can get it slowly.

Glue removal method: 1. Vinegar is used to remove glue.

Apply the vinegar evenly with a cotton swab on top of the residual film glue, wait for a while after the vinegar and glue are fused, and slowly remove it with a cloth or spatula.

2. Remove with banana water.

Banana water can remove the gum, but it doesn't work very well.

3. Wind oil essence degumming.

Apply the wind oil essence to the glue many times, slowly scrape with a knife, and be patient.

4. Alcohol glue removal.

This method is more effective than the first three, apply alcohol to the glue, the glue will be softened, and it will be scraped off slowly with a knife.

5. Remove glue from automobile thermal insulation cleaning agent.

Spray the glue to be removed with a special car thermal insulation cleaner, the glue will be melted immediately, and it can be wiped off with a cloth, which is very labor-saving and time-saving.

1.Wipe with a damp rag;

2.Spray with a special degumming lotion;

3.Wash with foaming detergent;

4.Wipe with vinegar, and remove with a scraper after the vinegar and glue are fused;

The glue of the car film can be softened with alcohol or wind oil, and then scraped off with a small plastic skid. When softening the remaining glue, alcohol or wind oil essence can be evenly applied on top. If you don't soften the glue, you just scrape it with something, which will leave a lot of scratches on the glass.

After softening the glue with alcohol or wind oil, use a plastic pick to scrape the glue, and be sure not to use a relatively hard metal object to scrape the glue. When sticking the film, be sure to choose the best film, the light transmittance of the inferior film is not up to standard, which will affect the driver's vision when driving at night.

A professional adhesive removal tool is required, and it can be cleaned with a glue remover or cleaning solution. However, you need to be extra careful when using a glue removal knife to avoid scratching the glass. If you don't have a glue remover or cleaning solution, you can also use alcohol or wind oil essence, both of which can soften the adhesive and make it easier to remove.

For the glue on the car glass film, if you want to remove it, you can use alcohol to wipe it, which is easier to remove the glue on the glass.