Word document always shows how to fix the revisions

Step 1. Once the document is open, click Show Markers under the Review tab, check Annotate, Ink, Insert & Delete, Format, and so on as needed.

Step 2. Click the drop-down menu of the "Revision" option, and in the pop-up "Revision Options" window, click "Advanced Selection", and set the options such as "Mark", "Move", "Table Cell Highlighting", "Formatting", "Comment Box" and so on.

Step 3. After the setting is completed, click the "OK" button to modify the document, and the following figure shows the effect of deleting two words.

If you want to remove traces of changes in one of these places, you can right-click on it and select "Accept Deletion", and the word "Network" disappears, or "Refuse Deletion" reverts to the original state. If you want to completely eliminate the traces of revisions, click "Revisions" first, and then under the "Show Marks" option, check off the "Annotations", "Ink", "Insert and Delete", and "Format" tags. It should be noted that you must click to dismiss the "Revision" state before performing other operations, otherwise even if you save and exit, the modification trace will be displayed again when you open it again.

If a document copied from someone else is opened, and a lot of revisions are displayed, and you agree to the changes, then you can, the first step, select "Accept all revisions" (of course, you can also accept them one by one), then the document has no traces of revisions, and the second step is to turn off the revision function, that is, click the "Revision" button again, and close it. My version of Word may not be the same as yours, but the two buttons mentioned above should be in the "Review" function, you can look for them.

First, open the revised document as shown in the image below:

Click "Review" in the toolbar to find "Revision", find the small arrow below the Revision tool, and click it, a drop-down menu appears, and select "Revision Options", as shown in the following figure:

In the pop-up Revision Options setting box, find the Comment Box, as shown in the following figure

Select "Never" after the "Use Comment Box" option and click "OK" as shown in the image below

Then in the toolbar "Review", find the "Accept" bar, click the small arrow below, the drop-down menu appears, and select "Accept revisions to all documents", as shown in the following figure:

At this point, open it again.

documents, revisions will no longer be displayed, as shown in the following image:

You can tell from the ** in the question that the area is blank because it is currently in the review options, and the comment shows a revision status. The workaround is to go through the Review menu, click on the comment box drop-down arrow, and display all revisions as an embedding to make changes. Specifically, take word2007 as an example, and the setting method is as follows:

1. Open a word document on your computer to enter.

2. After entering the document interface, you can see that there is a blank page on the right side of the current interface.

3. Click the Review button in the menu bar.

4. Click the drop-down arrow in the comment box in the options that appear.

5. At this time, check the Show all revisions button in embedded form in the options that appear.

6. At this time, you can see that the blank page that existed on the right side of the word interface has disappeared.

Hello, kiss <>

If you are in silver hole revision mode every time you open it while using Word, it may be due to the following reasons:1Revision mode is not turned off:

If you turned on revision mode the last time you used Word, but it didn't turn it off, it will still remain in revision mode the next time you open Word. You can turn it off by finding the "Revisions" option in the "Review" tab of Word. 2.

Template setting issues: If you are using a specific Word template, it may cause Word to be in revision mode every time you open it. You can try changing to a different template or resetting the current template.

3.Word setting issues: If your Word settings are wrong, it may cause it to be in revision mode every time you open it.

You can find the "Advanced" tab in "Options" in Word, check if the "Enable Tracking Changes" and "Enable Revisions" options in "Options" are ticked. If the above methods do not solve the problem, it is recommended that you try to reinstall Word or contact Microsoft official customer service for consultation and resolution.

1. The first thing is to open the revised word document on your computer, as shown in the figure below.

2. Then click [Review] on the menu bar, as shown in the figure below.

3. Then click on the small lower triangle under [Revision], as shown in the figure below.

3. Then click [Revise Options] in the options, as shown in the figure below.

4. Then select [Never] in the drop-down box of [Use "Comment Box" in the pop-up window, as shown in the figure below.

5. Then click the [Confirm] button to complete the operation, as shown in the figure below.

6. Finally, click on the [Accept All Revisions to the Document] option under [Accept], and then we can see the result we want, as shown in the image below.

woldUnrevision formatting requires all markup views to be turned off in the wold settings.

Take Office 2017 as an example, close the so mark view in Word, and the steps are as follows:

1. In the menu bar at the top of the Wold main page, click on the Bird Rent to select Review to enter the review menu bar.

<>3. In the pop-up menu bar, click Annotation and Formatting.

4. Select None in the Annotation & Formatting options.

5. Click OK to complete the cancellation of Word revision mode.

Word is in revision mode every time it is opened as follows:1. Open the document you want to modify, before you modify, switch to the review option, swipe and then find the revision option, click on the defense to make it selected.

2. Then click the drop-down arrow to open a menu, select the revision option, and set the revision option.

3. I saw a dialog box opened, where I set the display method of three modification methods, the newly inserted content is underlined, the deleted content is struck through, and the revised line is outlined outside; You can also set different colors for different content, which will not be demonstrated here.

4. Next, there are two commonly used ways to set the annotation, the first letter is as shown in the figure, check the embedding method, see the red font inserted "largely" and the later deleted "times", the deleted content is embedded in the article.

1. First of all, open the word document that needs to be changed, and then click Review in the navigation in the upper right corner, and you can set it to review mode by entering the review button to view. Open the Word document. Click Review in the navigation bar above to review the interface.

2. In the review interface, there is a revision button, from which you can mark the document and modify the author name information. Enter the name of the author of the revision, and the next time you see who made the revision, the name of the author will be displayed directly.

3. Modify the author's name. Click on the bottom side of the Revise button and select Change Username. By default, the computer is logged in, and the administrator can enter the name of the Chinese character.

4. In the common options, click on the user name, enter the name of the user name in the input box, and save it after you change it. The user name is automatically saved.

5. Turn on the revision trace. After editing the author information, click on the top side of the selection revision to start opening the revision trace. After you edit a document, the system automatically displays the document's modification information on the right.

6. When deleting or adding text to the document, the system will automatically add the information of the modifier who has been operated, the operation time and the operation content. In this way you can see the addition of the document and remove some of the markup made.