What should I do if the lights at home are not lit, but the sockets are all electric?

The lights at home are not lit but the socket has electricity, which means that there is no problem with the power supply, and the socket and lighting are controlled by two circuits respectively, and the circuit of the lighting part may have a short circuit or trip, so the lights are not lit. It is recommended to check whether the lighting circuit is short-circuited in case of power failure and whether the air switch of the sub-control lighting is tripped.

It may be that the total single-phase leakage protection is tripped or broken, and the zero live wire is reversed, resulting in the appearance of the socket pen after tripping.

The test has electricity. There is another one, which is that the socket plug-in electrical appliances you said are working normally, but all the lights in the house are not on, then the air opening of the independent control lamp is broken, and it should be good to replace one.

Generally, the current home power distribution system is the power supply of the lamp and the power supply of the socket is separated, controlled by two air switches, you look at the power distribution panel at home should have an air switch tripped, you can try to close the power transmission once, if the power can be used normally after the power is sent on it, if the power is still tripped, do not send the power again, find the property maintenance personnel to deal with it.

Check whether the air switch of the lighting circuit at the main switch has tripped, and it should be pushed up.

If the air switch is pushed up, but there is no power in the lighting line, it is necessary to overhaul the line in front of the air switch.

The lights at home are not lit, it may be that the fuse tube that controls the lighting is blown, it is recommended that you go to an experienced electrician to replace it with a new one.

Now the electrical wiring, are a socket a circuit, a lamp circuit, the socket has an electric light is not on, may be tripped, I hope it can help you.

It is possible that the light gate has been dropped.

Summary. The lamp has an electrical socket and no electricity is what is going on as follows;

1.This is usually due to a short circuit in the electrical cord of the power plug, whose socket is not on the same line as the lighting fixture.

2.If there is a line fault in the power socket, check whether the power switch is short-circuited, and if so, please replace it with a new power supply.

3.If the socket is old, one socket will be out of power, but the light will be electric.

4.The power plug is not turned on (some plugs have an automatic control switch).

5.A dedicated voltmeter is used to measure whether there are wires inside the plug. If there is a problem with the outlet, it will also cause a power outage. If the wires of the power plug are burned, the internal power supply will be de-energized.

6.If it doesn't work, the fuse is broken and have an electrician repair.

7.This is because of a wire failure at one of the outlets. There are two wires connected between the plug and the lamp, if there is a problem with the socket, it will not affect the normal operation of the lamp, but it will show that there is no electricity.

If this is the case, check the power supply for a short circuit before replacing it with a new one.

8.The lamp and the power of the outlet are not on the same branch, but are controlled by two air switches.

9.The above situation shows that these are two routes, that is, the exit is one.

All the outlets in the house are out of power, but the lights are on what is going on.

The lamp has an electrical socket and no electricity is what is going on as follows; 1.This is usually due to a short circuit in the electrical cord of the power plug, whose socket is not on the same line as the lighting fixture. 2.

If there is a line fault in the power socket, check whether the power switch is short-circuited, and if so, please replace it with a new power supply. 3.If the socket is old, one socket will be out of power, but the light will be electric.

4.The power plug is not turned on (some plugs have an automatic control switch). 5.

A dedicated voltmeter is used to measure whether there are wires inside the plug. If there is a problem with the outlet, it will also cause a power outage. If the wires of the power plug are burned, the internal power supply will be de-energized.

6.If it doesn't work, the fuse is broken and have an electrician repair. 7.

This is because of a wire failure at one of the outlets. There are two wires connected between the plug and the lamp, if there is a problem with the socket, it will not affect the normal operation of the lamp, but it will show that there is no electricity. If this is the case, check the power supply for a short circuit before replacing it with a new one.

8.The lamp and the power of the outlet are not on the same branch, but are controlled by two air switches. 9.

The above situation shows that these are two routes, that is, the exit is one.

After the end of the upper right corner, please give a like, thank you.

Reasons why there is electricity in the socket at home but all the lights are not lit: circuit breaker problems, open circuits, tripping of sub-switches or poor contact of the pile heads of incoming and outgoing switches, etc.

1. Circuit breaker problem

Check whether the circuit breaker trips or trips, and if there is a problem with the circuit breaker, replace it as soon as possible.

2. Break the circuit

To break the circuit, you need to find a breakpoint.

An inductive pen can be used from the off-distribution box.

I started with the nearest electric light.

3. The branch switch trips or the pile head of the inlet and outlet switch is in poor contact

Pull down all the branch switches, and then close them, you can solve it, if it is a switch with leakage protection tripping, pay attention to press the reset button to close.

Precautions for installing sockets

1. Pay attention to the location of the installation socket

When installing the socket, it is necessary to stay away from some dangerous places, and be careful not to install it on the gas meter.

Faucets, bedheads, stoves and waterproof boxes, etc., otherwise it will not only affect the normal use function of the socket, but also easily occur problems such as gas**, circuit failure, and human electric shock.

2. Make safety preparations

Before installing the socket, it is necessary to pay attention to disconnect all the dangerous power supplies in the room, and clean up the debris and dust in the socket base slot, otherwise it will bring certain danger to the builder during the installation process, harm to human health, and cause people to have the problem of electric shock.

3. Select the socket type according to the installation location

When installing sockets, it is necessary to choose different kinds of socket products for use according to the characteristics of different places of use. For example, in places with a lot of water consumption, such as bathrooms and balconies, where water is easily exposed, the sockets used should be splash-proof.

First of all, standardize the wiring, lighting (lights) and sockets are divided into different lines, that is, controlled by different air switches, socket lines tripped, and the lamp lines did not trip, so it is normal for the socket to have no electric lights and electricity.

Check the total distribution box, whether there is an air switch tripped, if there is a push up, if pushed up and jumped down, it means that the electrical appliances in the socket line are leaking or short-circuited, and the fault needs to be eliminated and then pushed the brake.

The lights at home are out of power, the socket is powered, whether all the lights are out of power, is to check whether the lighting in the gate box has jumped, or the wire is loose and has not been in contact, because now the general lighting and sockets, air conditioners, kitchens, and bathrooms are installed separately with air switches.

The socket and the light are not the same line!

The socket may have individually controlled switches. Go to the gate box to see if there is any tripping.

1: The insurance of the socket is off (now the general lighting and socket of the residential room and the air conditioning socket are separated) 2: The socket is not plugged in (check whether there is poor contact at both ends) 3:

The socket is broken (the socket is aging, and there is a possibility of disconnection inside) 4: The switch on the socket is not turned on (some sockets have their own switch control) 5: Wait, it will be fine after a while (if someone misses you, God will inform you in this way).

The wire is broken or incorrectly wired.

Summary. The reason why the lights are not lit, but the sockets are powered is caused by an open circuit in the household circuit. The solution is: you need to contact a professional electrician in time to overhaul the copy circuit, which can solve the problem that the lights are not lit.

The live wire and the neutral wire of the two binding posts connected to the lamp holder collide; The two wires in the socket or plug collide; The live wire and the neutral wire are directly connected and cause a short circuit. The short circuit will blow the fuse and cut off the entire lighting circuit, and in serious cases, it will burn the line and cause a disaster.

For example, the lampholder, switching, and hanging box are not in good contact; Poor fuse contact; Poor contact at the line joint, etc. This will make the lights flicker on and off, and the electrical appliances will not work continuously and normally.

Extended information: The use of household circuits is described below:

The two interrogation posts of the socket are all connected to the live wire or neutral wire; The switch is misconnected to the live wire in the main line; The bulbs are connected in series in the circuit. The water heater socket has no ground wire, the switch controls the neutral wire, the light off light is still strobeling, and the neutral ground wire is reversed.

As soon as the electric leakage switch is used, it trips.

Use a voltage tester to check the switch of the main switch. If there is electricity, then use the school fire lamp head (a good incandescent lamp, lead out two wires on the lamp holder to become the school fire lamp head) in parallel on the two binding posts under the gate knife switch, if the light is on, it means that the entrance line is normal (A: If the light is not on, it means that the entrance line is open, and only the entrance line needs to be repaired).

What should I do if the lights at home are not lit, but the sockets are all electric? The sockets at home are electric, and the lights are not on for any reason.

The reason why the lights are not lit, but the sockets are powered is caused by an open circuit in the household circuit. The workaround is:

It is necessary to contact a professional electrician in time to overhaul the copy circuit, which can solve the problem that the lights are not lit. The live wire and the neutral wire of the two binding posts connected to the lamp holder collide; The two wires in the socket or plug collide; The live wire and the neutral wire are directly connected and cause a short circuit. The short circuit will blow the fuse and cut off the entire lighting circuit, and in serious cases, it will burn the line and cause a disaster.

For example, the lampholder, switching, and hanging box are not in good contact; Poor fuse contact; Poor contact at the line joint, etc. This will make the lights flicker on and off, and the electrical appliances will not work continuously and normally. Additional Information:

The use of household circuits is introduced as follows: the two interrogation posts of the socket are all connected to the live wire or neutral line; The switch is misconnected to the live wire in the main line; The bulbs are connected in series in the circuit. The water heater socket has no ground wire, the switch controls the zero wire, the light off is still strobeling, and the ground wire of the zero wire is reversed and trips as soon as the electric leakage switch is used.

Use a voltage tester to check the switch of the main switch. If there is electricity, then use the school fire lamp head (a good incandescent lamp, lead out two wires on the lamp holder to become the school fire lamp head) in parallel on the two binding posts under the gate knife switch, if the light is on, it means that the entrance line is normal (A: If the light is not on, it means that the entrance line is open, and only the entrance line needs to be repaired).

If my answer is helpful to you, please give a thumbs up (in the lower left corner), I look forward to your like, your efforts are very important to me, and your support is also the motivation for my progress. If you feel that my answer is still satisfactory, you can click on my avatar for one-on-one consultation. Finally, I wish you good health and a good mood!