There are white particles at the water inlet, what is it, how is it generated, and how is it solved?

This is limescale, calcium carbonate in water.

Precipitated, so generally can not solve the root cause, just deduct it directly, it's okay to get it once a few months, it won't affect it very much, the higher the water temperature is stable, the easier it is to produce.

These white particles are rust, which proves that the quality of the water is not good, plus the heating time is long, because it is the water heater that is repeatedly heated, this white particle will be produced, that is, the water is alkaline water quality.

This is the oxide of water, because there is no evolution of white matter, why do you say that people drink water to drink pure water, because after pure evolution, the human body needs calcium, just pure water has calcium, there is no purified water, there is everything, and there will be white matter for a long time.

For example, solar water pipes, where water seeps into and out of the water inlet, also have this white crystal. It may be formed after the water has evaporated.

This white particle is commonly known as water rust, and it will also be the impurities in the water, so it will be adsorbed on the water inlet, this kind of thing is very hard, so it is not easy to handle

Abstract: Answer: There is a common quality problem in the production of red bean curd, green bean curd and white bean curd, that is, in the later fermentation, there are white particles on the surface of the tofu blank, which are white round grains, pasted on the surface of the blank, sometimes more, sometimes less, sometimes a single existence, sometimes several gathered together, a strand of white particles appears in the late fermentation for about 1 month, the longer the time, the more the quantity, to a certain extent, the quantity does not increase, and the probability of the appearance of white particles is about 1. That is, out of 100 bottles of finished products, 1 bottle appears

That's the scale of garbage oil, the result of emulsification, very hard, lumpy, milky white, more and more in the sewer, in serious cases, it will be plugged in the sewer, making it difficult to clean the sewer, and then pour oily water into the sewer, and then flush it with water that does not contain it, which can effectively alleviate the generation of this kind of substance, I hope it can help you, I hope to adopt.

1. Scale, if the water quality is hard, there is more scale, it will accumulate on the wall of the water pipe, and it will form something similar to lime blocks over time, which is difficult to deal with, and it is recommended to replace the sewer pipe.

2. The mixture of oil and impurities, there will definitely be a lot of grease and other things in the kitchen, and the water pipe will be blocked after a long time, which can be cleaned with dish soap or hot water, or directly replaced.

Causes: 1. The electric heating wire inside the water pipe does not work;

2. The electric heating wire inside the water tray does not work;

3. The direction of the drainage pipe is unreasonable, resulting in water accumulation in the pipe of the cold storage;

Solution: 1. Manually remove the ice inside the water pipe, and the drainage pipe can be removed and placed in an outdoor room temperature environment to wait for the ice to melt.

You're talking about limescale, right? If the hardness of the water is particularly high, it is best to add purified water or softened water to the inlet of the water heater.

It feels like it's supposed to be a fish egg, but it's not entirely certain. It also depends on what kind of fish you have. It is normal for goldfish to spawn on grass, but it is quite difficult to hatch them.

If it is a newly raised aquatic plant tank, it may also be the eggs of insects and other aquatic organisms, such as the eggs of snails.

Reasons:1Grease produced from the remains of micro-raw materials or old waste, bait, organic matter, etc.

2.There are too many fish, and the excrement of the fish cannot be filtered by the filter cotton, and only the oil film processor can be installed; Or raise some tank fish.

3.The filter media in the filter is too dirty, and grease is spilled.

Solution:1Close the lid of the fish tank.

2.Raising oil-based fish (fish that float on the surface of the water and eat dirt), such as black horsepower, black girl, black teapot, etc., can reduce the production of oil film.

3. Use the oil film processor to make the water inlet of the filter connected to an oil separator and filter it for a few days, and the oil film enters the filter, and the filter cotton in the filter material is used to adsorb, and the oil is decomposed by nitrifying bacteria.

4..3 times as described for nitrifying bacteria; After 3 days, put a packet of granular activated carbon in the middle of the two layers of filter cotton, and the water will be very clear after a week.

5.Replace the filter cotton, be careful not to buy the filter cotton of poor quality, and clean the dirt in the filter in time.

6.To remove the oil by blotting paper, you can put the oil blotting paper at the opposite corner of the water outlet (oil film concentration area) to absorb the oil.

Just change the water, don't be so troublesome!

You've got to have a problem with the tank. Didn't you buy it and didn't soak it well? My tank turned out to be like that, what fish raise and what die, reason 1 is the problem of glass glue, 2 The harmful bacteria in the tank inhibit the beneficial nitrifying bacteria, and a good ecological environment has not been established.

It is recommended that you reopen the cylinder: wash the cylinder several times, then fill a tank with water, and then sprinkle a few packets of salt on him, as long as it will dissolve, continue to sprinkle, the concentrated salt water will remove all the germs, odors, and a layer of unstable glass glue on the surface, so a tank of salt water is quietly raised for more than a week (must endure it).

When the tank is over, clean all the water in the tank, start to raise water, fill a tank of water, and turn on the pump. After 3 days of water and pump, you can start to lay a few peacocks or zebras or the like, we call it open tank fish, and the water feeding time should be more than 2 weeks to 1 month - I didn't hold on, and I released the fish after three days, but fortunately, now the water in my tank is clear and the fish is alive without algae, you should hurry up! Don't stop the pump, the fish is all over and cleared in time, and by the way, change some water.

The fish bowl seller said that it was okay to soak it in tea water, but I didn't try it.

I'm also a newbie, so I can communicate if I'm interested.

This shows that your fish tank is small and there are relatively many fish, and the fish are not proportional to the tank, and the breeding density is slightly larger.

This needs to be replaced with a larger fish tank, or the water can be solved frequently, and the water change should be carried out every day, and it is best to use the same water temperature as the current tank to avoid the fish from catching a cold. The method is to dry the tap water indoors for about 2 days, which not only removes the chlorine in the water, but also adjusts the temperature.

Since that's the case, you should choose Qingqing Leaf 6574. His method is correct, and I won't go into it here.

Replace the water in the entire fish tank.

Strengthen physical filtration, open surfing.

A filter device is installed at the bottom of the water pipe, and the mesh must be fine.