How to deal with the water leakage in the Jinsong washing machine?

1) From the front of the washing machine, if the right rear part leaks, it means that the connection between the drain pipe and the drain pump is not real, or the rubber connection pipe between the drain pump and the filter has a sand hole, a tear or the connection is unreliable, or it may be that the screws at the sealing place of the drain pump body are loose.

2) If the right front of the washing machine is leaking, it may be that the filter bellows or connecting pipe has sand holes, cracks and poor connection.

3) The middle of the washing machine is leaking, the reason is that there is no fastening between the outer cylinder body and the front cover, that is, the screws of the outer cylinder buckle ring are loose, or the metal pressing plate connected by the rubber bellows is not firmly fastened with the outer cylinder, or the outer cylinder weld is not firmly welded, or the outer cylinder sealing ring has cracks.

4) There are two reasons for water leakage at the fork frame behind the outer cylinder: one is that the rubber sealing ring between the fork frame and the outer cylinder is not properly assembled or the sealing ring is damaged. The outer cylinder fork can be removed, the seal can be reinstalled, or the seal can be replaced.

When installing the new sealing ring, when the sealing ring is embedded in the shaft hole of the outer cylinder, the triangular convex side of the sealing ring should be facing the fork frame; The other is that the inner cylinder bearing is worn, and the gap between the inner cylinder shaft and the bearing is too large, resulting in water leakage and high noise, and the inner cylinder bearing should be replaced.

This may be caused by a coin somewhere when you are doing laundry, you can open the back cover to see.

Panasonic drum washing machine door leakage generally has these reasons;

1. The cause of water seepage in the drum washing machine: the drainage rubber bowl is damaged.

Solution: Do not use hot water too high, and drain the stagnant water in the pipe in time after each washing.

2. The reason for water seepage in the drum washing machine: the spring elasticity is reduced, which makes the water glue bowl and the drain not tight enough.

Solution: When there is no water in the barrel, it is not advisable to start the machine, so as not to cause premature wear of the sealing ring and water seepage.

3. The reason for water seepage in the drum washing machine: the path of spring compression and extension deformation is slightly deviated from the central axis of the spring, so that the drainage rubber bowl cannot be pressed on the drainage port in the middle position.

Solution: To prevent mechanical damage, do not force the drain pipe, and keep the drain pipe clean; It is best not to put the washing machine in a damp bathroom, otherwise the shell is more likely to deteriorate.

1. Front door. If there is a leak in this area, it means that there is frequent use and excessive shaking of the outer cylinder, which causes the fastened nut to loosen and cause the seal to be loose. 2. Water leakage at the water inlet part, which is caused by a variety of reasons, first of all, the water inlet pipe is not well connected to the water inlet valve, or there are cracks in the connecting pipe between the water inlet valve and the detergent box, and the loose clamp ring will also lead to water leakage.

3. Poor connection at the bottom of the washing machine will also lead to water leakage at the bottom. Suggested treatment: 1. Disassemble the glass window, remove the nut, remove the glass window, then dump the washing machine, reinforce the nut with a card ring, and then reinstall it.

2. You can add a rubber gasket to the water inlet pipe, install it into the water inlet valve and tighten it, or replace the new water inlet pipe. Replace the water inlet pipe or washing box with a new one, and find a special person to repair and install it. 3. Check the connection of each part of the washing machine, and find the leakage place for maintenance and concealment for the bottom leakage, and replace the drain pipe or reconnect the connectors.

The reason is that the connection between the drain pipe and the drain pump is not real, or the rubber connection pipe between the drain pump and the filter has a sand hole, a tear or the connection is unreliable, or it may be that the screws at the seal of the pump body of the drain pump are loose.

Hello, I'm glad to reply to you, the treatment method of direct water discharge after the Panasonic washing machine enters the water: 1. First cut off the power supply, check whether the drain valve core is stuck in the power-off state, and then see whether the position of the valve core rod is in place, it is very likely that the internal spring is stuck. In this case, we should unscrew the valve cover and check whether there is something stuck inside or whether there is a part damaged, if something is stuck, just take it out, if there is a part that is broken, just replace it.

2. If the drain valve is normal, then check whether the tow bar of the tractor is easy to carry. You can directly pull the towbar back and forth with your hand to see if it is flexible to follow the movement, whether the internal spring is elastic enough, and whether it can open the drainage core. If there is a situation where it is stuck or cannot be opened, it means that the inside of the retractor is damaged and the retractor needs to be replaced.

3. If the retractor is normal, you can check whether the retractor has action to shake the drain valve for drainage in the case of power and water intake, if there is a description of the program of the computer board is out of order, the computer motherboard should be replaced. 4. There may also be problems such as the buried water level switch or the pressure that cannot sense the water level, and the failure of the water level sensor leads to drainage while entering the water. This can be solved by replacing the water level switch or the water level sensor.

5. The rupture or loosening of the water pressure conduit will also lead to failure, because there is no way to provide a pressure to water level switch or water level sensor. It can be solved by adjusting or replacing the water pressure air duct. 6. There is also to check whether there is water leakage in the central shaft, and the motor is burned out, and the motor needs to be replaced in this case.

I hope it will be helpful to you, and you can always find the teacher if you have any other questions in the future. I wish you all the best in your life.

1. It may be that its panel door is not closed properly. 2. If the water still enters the water when it reaches the preset water level but the wave wheel starts to run, it means that it is a problem with the water inlet valve. At this time, unplug the power supply line of the water inlet valve, if the water is still in, it means that the water inlet valve is broken, and it can be replaced.

If the water inlet stops after unplugging the power cable, it means that the computer board relay is sticking.

Recommendations and solutions:

1. The washing machine is an indispensable household appliance in life, and if there is a problem with the use of guess the world, it will also lead to frequent failures. If it is the first time to use, read the instructions carefully and follow the operating instructions. It is also necessary to pay attention to the power outlets.

It should be reasonably arranged to avoid electric shock accidents.

2. Do not place flammable or corrosive materials next to it, and it is best to put it in a ventilated and dry place. There is a lot of noise during operation, and it is necessary to check whether the ground is flat and return to the front level, and it should be used in a flat place.

3. Some consumers will use boiling water to wash their clothes, but it will also cause a sealing ring.

Deformation occurs in aging, and once there is a problem of poor sealing, the service life will be greatly shortened.

4. After washing clothes, do not close the lid, open the hatch to ventilate it and avoid bacterial growth.

5. If you can't handle the ear code yourself, you have to find a professional to deal with it.

Summary. Dear, I'm glad to answer the question for you: Panasonic washing machine comes out directly after the water enters? Check whether there is a foreign object (coin, brooch, button, etc.) stuck in the drain valve core, resulting in the drain valve core can not return to the position and can not turn off the water.

I am happy to answer the question for you: Panasonic washing machine directly out of the water after the water enters? Check whether there are foreign objects (coins, brooches, buttons, etc.) stuck in the drain valve core, resulting in the drain valve core can not return to the position of the limb can not hold the water, drain the water while entering the water, take out the foreign body drain valve can be reset normally.

After checking Wang Pai, it is not a problem, it is necessary to check whether the drainage traction or the introducer (drainage motor) is faulty, whether the tow bar is flexible when pulled back by hand, and the drainage cable does not return to the position will lead to drainage while staring at the water ingress, and the solution is to replace the drainage tractor.

The Panasonic drum washing machine drains water after starting the water intake, the water level sensor is normal, the drain valve is normal, and the drain valve automatically opens the spool to drain the water after starting.

That is, the water pressure air duct is ruptured or loosened and failed, disassemble the rear cover, and this plastic pipe on the surface of the rear state shed is the air pressure intake pipe. Carefully inspect the plastic pipe and find that the connection is broken, then the washing machine cannot provide the pressure to the water level switch or the water level sensor, resulting in water inlet and drainage, the solution is to adjust the water pressure air duct to the appropriate position or change the water pressure air duct to a new one.

The trachea is normal and not broken!

Pro: After the potato bush starts, the drain valve automatically opens, and the spool is discharged, and the hand is sakura, if these are normal, it may be a problem with the panel or bush digger controller, which needs to be checked by the maintenance personnel to know the common faults.