Chopard has a faulty watch, how can I be sure where the fault occurred?

A true luxury watch never leaves any regrets for the buyer, and every aspect of the workmanship, from the exterior to the movement, is so delicate that it is impressive. As a result, the watch is truly worth the money. But at the same time, fakes are slowly beginning to flood this small market.

Ten tips for connoisseurs to distinguish the authenticity of a watch will be helpful to you who love watches.

1.Look at the movement.

First of all, it is necessary to be very familiar with the model of the movement used in the real watch and the movement logo, so that if you encounter a fake watch with a transparent caseback, you can distinguish the authenticity at a glance. Secondly, it is necessary to carefully observe the words of the movement, the engraving of the words of the genuine movement is clear and beautiful, while the fake watch is rough and unaesthetic. Finally, it is necessary to have an in-depth understanding of the performance of the movement, such as the winding method (manual or automatic, unidirectional or bidirectional), the sound of the movement running time, etc.

2.Change the label after reading.

To look at the factory label on the back of the watch, usually the brand logo will be on the label of the famous watch, and there is an identification of the number of watch models. Some watches also have a laser laser on the back label.

10 tips to distinguish the authenticity of a luxury watch.

3.Look at the subtle parts of the appearance.

First of all, we must carefully observe the appearance of the watch, including the polishing of the appearance: see if the polishing technique of the watch is delicate, the polishing of famous watches is very particular, and the craftsmanship of fake watches is far from it.

Font: The font of the real watch is full, and the fake watch looks lacking in confidence. Features:

Most fake watches will work their functions, which is a breakthrough to see through fake watches. Many fake watches function as decorations (e.g. moon phases, perpetual calendars, tourbillons, etc.) but do not actually have this function. Pointer:

The hands of the original can be distinguished from the fake in terms of length, thickness, shape and material. For example, the "blued steel hands" often used in luxury watches are a rich dark blue color of the hands of real watches, which are fired by a complex process, while the blue of fake watches is brushed up. Disk:

The most commonly used dial techniques for luxury watches include enamel, guilloché, metal radial dial, shell dial, etc., and some watches also have their own unique technology, such as Rolex's computer disk, Cartier's pure gold and silver-plated engraved dial, etc. Diamond and setting process: Look at the setting process, the quality and size of the diamond.

4.Look at the watch glass.

The glass of most watches is made of sapphire crystal glass, and the easiest way to distinguish it is to tap the glass surface with your finger, and a real sapphire crystal will make a crisp sound.

5.Look at the numeric number identification.

If you look carefully at all the numerical markings on the back of the watch, the fake watch is usually irregular, and even does not correspond to the number of digits of the real watch. The real watch is individually numbered.

The main reasons why the watch does not go are: the movement gear is misaligned, the watch is magnetized, bumps, and the oil sludge is dried for a long time when it is left on hold. The most common reason for the failure of the watch not going is the lack of power of the watch and the movement of the watch does not work.

When the mechanical watch stops, the priority is to think about whether it is caused by lack of power. Hand-wound watches should be wound at the same time every day as much as possible so that the watch can operate with sufficient energy for the next 24 hours. Quartz watches, on the other hand, can be actively wound and should be worn on the hand for more than 8 hours a day to replenish the mainspring.

Lack of exercise after wearing it will also show that the watch does not move or stop.

If the watch is used for a long time, then its wear and tear will be more serious, and the external maintenance of the watch will be easily damaged. It is necessary to regularly replace the watch you are wearing, and it is necessary to maintain the watch regularly, for the service life of your watch, it is better to maintain it regularly.

The materials of watch straps are mostly leather, metal and rubber, and each material has its own merits, and the problems faced are also varied, so daily maintenance needs to be "right medicine".

Daily maintenance of leather straps: It is recommended to pay more attention to keeping the strap dry and clean during daily wear, and try to avoid contact with liquids. In case of contact with liquids, such as rainwater, it is recommended to wipe immediately with a clean towel and then dry.

After washing, apply a little leather oil to the strap to give it an extra layer of protection and keep it shiny as new.

Avoid prolonged exposure to sunlight to slow down the aging of the band.

Go to a place that specializes in repairing watches, or buy a set of watch repair tools online and handle it yourself.

You can go to the repair center to detect what the fault is, or you can directly replace it with a new one.

In fact, there are many reasons why mechanical watches do not go, such as: bumps, movement gear misalignment, magnetization of the watch, shelving for a long time, sludge drying, etc., generally divided into two kinds, the first is because of insufficient kinetic energy. The second is due to a malfunction of the mechanical watch.

The kinetic energy is insufficient, and the automatic watch uses the movement of the arm to complete the winding. If the watch is left for too long or the amount of arm movement is less every day, the mainspring energy of the watch will be due to insufficient winding, and it is easy to produce inaccurate timing or night stopping.

Our mechanical watches often have the situation that the time is not accurate, and most people wonder if the mechanical watch is broken. There are many reasons why a mechanical watch can be parked, but there are several main reasons.

1. Insufficient kinetic energy: The watch is not winded enough, and the kinetic energy is insufficient. In particular, automatic watches require more arm movement, and the winding efficiency is very low. If you usually exercise a little bit, you can wind it manually, which can ensure enough kinetic energy.

2. Gear failure: Gear train failure such as deviation wheel and center wheel failure will lead to the condition of stealing stop of the watch. These situations are often not easy to detect and require disassembly, careful inspection and testing to find out the problem and solve the problem.

3. Lack of maintenance: mechanical watches should be maintained every 2-3 years or so. If it is not maintained for a long time, a large amount of oil sludge will be generated inside. Friction between gears increases, causing slippage.

There will be after-sales ** on your warranty link, call after-sales ** to inquire about the after-sales address.

Reason for watch stealing:

1. If the watch is placed for too long or the daily arm activity does not meet the requirements of the watch winding, the watch will cause the mainspring to be insufficient due to winding, which will cause the watch to be unstable or stop when not worn at night.

2. Accidentally knocking or falling on the watch in daily use will also lead to the theft of the mechanical watch.

3. The failure of the hairspring is also one of the reasons for the stealing of the mechanical watch when it is running normally.

The power of the table is insufficient.

An automatic watch only needs to be wound by moving your arm, but if you don't exercise much, or if you don't wear your watch for too long, the watch may not be able to run out of time or stop due to lack of power. Of course, you don't have to throw your arms as a hula hoop in order to wind your watch, just move normally.

Wearing time is too short.

If it's really caused by too little exercise, don't worry, just take off your watch and shake it horizontally for about 2 minutes before going to bed, and of course you can also shake it for 4 minutes, because then it can walk longer. If your watch can be wound, you can also wind it clockwise. In order for your watch to last longer, it is recommended to have him wear it on your wrist for at least 6 to 8 hours a day.

Hairspring failure. If neither of the above two reasons is the case, it may be the cause of the hairspring. If you exercise too much, the clockwork will be tighter. If it is really a lack of power caused by the winding, usually between 9 and 12 o'clock in the evening, the "calendar function table" at this time his needle wheel began to drive the calendar wheel, the load is large, the watch is tired, at this time if the power is insufficient and no one pushes it, it is easy to stop.

During this time, don't reverse the dial, many mechanical watches have a plastic calendar wheel, and if you are not careful, you will break the gear, if you break the tooth, it will be stuck at this time every day, or it will no longer jump until a fixed date. That's why the mechanical watch stopped.

Bump failure. The parts of the watch are very delicate and small, if you are careless and accidentally bump into it, or if you are healthy and bump into it. This can easily cause the movement parts to fall off or break directly.

All automatic watches must be worn or wound regularly in order to function properly. If the mechanism stops working for a long time, it will cause the watch to deteriorate for a long time. Generally speaking, the power reserve of a large three-hand watch is probably no more than 38 hours, which means that if you do not wear the watch for more than 45 hours, the watch will eventually stop due to the exhaustion of the mainspring.

Reason for stopping:

The more common reason may be the lack of kinetic energy, automatic mechanical watches do not need to be manually wound, but to keep the mechanical watch on the hand to wear at least 8 hours of time, because the automatic mechanical watch uses the arbitrary swing of the rotor to wind up, and the rotor swings with the movement of the arm, so if the mechanical watch needs to be worn on the hand often.

But if you often wear it on your hand and don't walk, it may also be a lack of kinetic energy, and then we need to manually wind it.

After the above methods, the machine is not gone, here we can rule out the reason for the lack of kinetic energy of the mechanical watch, it should be the failure of the mechanical watch, if you are not a watch professional, it is best not to disassemble it rashly, please send it to a professional watch repairer for repair.

If a mechanical self-winding watch has not been worn for a while, its power reserve (42-48 hours, depending on the watch model) will be depleted and the watch will come to a standstill. To restart the watch, you need to wind it manually, loosen the crown (depending on the watch style) and turn the crown 30-40 times if necessary. This will allow for a sufficient power reserve to return to normal function.

A non-automatic watch must be wound every day until you feel the resistance of the crown, at which point your watch is fully wound. Be careful not to twist the crown of your hand-wound watch too hard to avoid damaging the mechanism.

If there is a problem with the watch, I recommend going directly to the watch after-sales center. After-sales is not only more professional technicians, but also the instruments are imported, more precise, and **also very transparent, will not be messy**. When not to go to a regular after-sales center.

Otherwise, if you are trapped, you can only blame yourself.

What to do if the mechanical watch is gone, how to wind the mechanical watch.

Watch suspension: Anyone who knows a little about mechanical watches knows that fully automatic mechanical watches are wound entirely by the swing of the arm.

Therefore, if the watch is left for too long or the amount of arm activity does not meet the requirements of the watch winding every day, the watch will cause the mainspring to be winding and the potential energy is insufficient, which will cause the watch to be unstable or stop when it is not worn at night.

If this happens, we can manually do an arc movement before the watch is placed. Or use the manual winding function to wind the watch. This keeps the watch with enough kinetic energy storage to keep it running until the next day.

Chopard's watch is relatively thin, broken, first of all, afraid that the glass ballast will run into the movement, damage the movement, the watch must be cleaned and maintained, cleaning and maintaining the watch is a high-tech job, not the general maintenance master can repair, there are many kinds of glass, such as: crystal glass, sapphire glass, tempered glass, watch glass, plexiglass, many kinds of materials, like Chopard this kind of watch, with a sapphire glass on it, I hope my answer is helpful to you!

Do not immerse this watch in water. In general, for watches with depth, the water resistance is directly proportional to the depth of the depth. There are many ways to make a watch waterproof. By adding a rubber gasket to the back cover of the watch, all watches can be waterproof.

Chopard watch aftermarket.

There are many reasons for the watch to stop secretly, but in addition to malfunctions, there are also problems with wearing habits that lead to insufficient power and stop-and-go. There are also yes, first of all, make sure that you have enough time to wear it every day, see if this situation will happen, and don't take it off and put it on the table as soon as you get to the office or when you get home.

If you ensure at least 7-8 hours of wearing time every day, there will still be a sneak stop, then it may be because the watch needs to be washed, of course, the watch you just bought generally does not say that you need to maintain the oil immediately, but it is possible that the watch you bought is in the counter for a long time, and some of the watches that are pressed in stock may be placed in the counter for a long time, if the counter has not been sold, put the watch for several years, because the internal lubricating oil is naturally aging, it is also necessary to wash the oil, Of course, this situation is very rare, because after all, it will not go away if you put it there, but it will not age so quickly if you put the lubricating oil.

Stop, there may be the following reasons:

1. See if the crown is pulled out, the crown is pulled out, and the watch stops.

2. Whether the second hand touches the glass, there will be a circle mark on the glass.

3. Whether the three watch hands are not well balanced, causing contact and causing stopping.

4. Whether the battery is exhausted or not, it generally needs to be replaced in 1-2 years.

If the watch needs to be repaired or maintained, or other needs, it is best to go to after-sales, which not only has a more professional technician and better service, but also its instruments will be more precise. ** It will not be reported like other places, there are standards. The after-sales service is on the seventh floor of Tower A on the side of Wanling Hui.

If the back cover is opened in a non-designated place, it will not be eligible for the warranty.