What kind of cement is used to make toilet waterproofing with Laurel, and what is its proportion?

Its ratio should be between 7:1 and 10:1, which is relatively normal, and the efficiency can achieve a very good effect.

It depends on the specific situation, under normal circumstances, its ratio should be about 1:10, this situation is relatively normal, relatively speaking, it is better.

Use instant cement for waterproofing, it's too two, that's not good, don't do stupid things, at least you have to use full-effect waterproof coatings. Or it is a mortar waterproof material. Don't try to be cheap, if you leak it in the future, you will be dumbfounded.

However, if you make the cement for bathroom seepage, it is not the reason for the cement, but because your protective net is related to your waterproof product, and if the box is horizontal, it is not a big update.

To do the famous waterproofing, you need to go to the building materials market to buy a professional waterproof material is cement mortar.

When decorating the house, the bathroom must be as waterproof and leak-proof as possible, because it is responsible for the downstairs and responsible for itself, so as not to renovate it after living in the future.

Well, what is the proportion of cement produced by Laurel to make the bathroom waterproofing? This is a professional, you ask to do waterproofing, they will definitely know what the ratio is.

Remember, I think you can make a setting according to his general ratio, which is generally fine.

If you want to make the bathroom waterproof, I recommend that you use cow felt better.

Generally, this decoration master will mix it for you, so don't worry too much.

There is a certain percentage of poor waterproof cement used for the toilet with old Lyle, and they have regulations.

Use. Lauler makes the cement of the old metasequoia in the bathroom, and its proportion is regulated.

If the waterproofing of the bathroom requires some special coating, these proportions are difficult to determine.

Actually, I think this is generally a 1:2 ratio.

What are the risks of employing people to work in the bathroom? He didn't even see what the rate was, and I went directly to the Yuping player according to their odds.

Just check your local cement, as for the ratio, you have to read its instructions.

The configuration of waterproof cement mortar for toilets is as follows:

Cement, 100 kg (2 bags);

Medium sand, 200 kg ;

Polymer waterproofing fluid, 4 kg (4% of cement);

Mixing requirements: accurate proportion, stirring evenly, sand sifting, thin and appropriate.

Not less than 1:1, but also mixed with waterproofing agent.

What waterproofing material do you use?

It depends on what kind of bricks are used, all tiles are made of 1:2 cement mortar and glued through the rows of tiles. Half tiles can be made with 1:2 cement mortar.

The dosage of waterproofing agent in waterproofing mortar: If the stock solution of waterproofing agent (1::50) of highly concentrated cement mortar is used, 1% of the weight of cement can be used.

That is, 1 bag of cement with 1 bottle of waterproof stock solution. Dilute into a water repellent before use. Dilution Method:

After adding 50 kg of water to 1 bottle (bottle), simply stir it, and use it instead of water to stir cement mortar. Cement to sand ratio: weight ratio) works best, with 1:

A ratio of 3 is also OK. If the waterproofing agent (diluent) is used directly, the common ratio is: cement:

Sand: waterproofing agent = ratio is sufficient.

The amount of waterproof mortar mixed with waterproofing agent is determined by the product, because there are many varieties of waterproofing agent, even if the concentration and production technology level of the same waterproofing agent are not the same, the dosage is not the same. Therefore, there should be a ratio in the product description of each manufacturer.

If you want to send it for inspection, the testing unit requires you to give the ratio of cement mortar, the amount of waterproofing agent, and the water-cement ratio before you can do the test. There is no specification for the dosage, but the performance of the waterproof mortar after being mixed with waterproofing agent is tested according to the requirements of JC 474 (2008) "Mortar and Concrete Waterproofing Agent".

You see that's how we do it.

Chisel the cement used for waterproofing.

Leakage prevention can be achieved by using a specially cemented rain shield.

Find the cracks of water leakage, and use the characteristics of Tianyudun sticky cement to achieve leakage, because Tianyudun is a kind of cement glue, which can stick to the cement and never detach, with elasticity and ultraviolet resistance, which is the best choice for you to repair the building and prevent leakage.

You will see how many people have been fooled.

Ground plastering cement mortar waterproof layer process:

1) Clean the base layer: clean the loose concrete, mortar, etc. on the cushion, and remove the bulging bulge.

2) Brush cement slurry: the mix ratio is cement waterproof oil = 1 weight ratio), add an appropriate amount of water to mix into a porridge shape, spread it on the ground, and sweep it evenly with a broom.

3) Plastering the bottom layer mortar: the bottom layer is made of 1 3 cement mortar, mixed with waterproof powder of 3% 5% of the cement weight. The mixed mortar is poured on the ground, scraped flat with a ruler, the wooden trowel is smooth, and the iron trowel is pressed again.

4) Brush cement slurry: brush cement slurry after 1 day interval at room temperature, and add an appropriate amount of water to cement waterproof oil = 1 weight ratio.

5) Plastering surface layer mortar: After brushing the cement slurry, then wipe the surface layer mortar, mix ratio and practice with the bottom layer.

6) Brush cement slurry: brush the last plain slurry (not too thin to meet the requirements of wear resistance) after the initial setting of the surface layer mortar, and the mix ratio is cement waterproof oil = 1 weight ratio), add an appropriate amount of water to make it closely combined with the surface layer mortar, and calender and compact.

7) Curing: After the ground has a certain strength, the surface is covered with sacks or straw bags often watered and wet, and the curing time depends on the temperature conditions, generally 7d, and the slag Portland cement should not be less than 14d, and shall not be subject to hydrostatic pressure during this period. The ambient temperature should not be lower than +5 in winter.

For reference: 10 cm is quite a wide slot. Clean the groove first, do waterproof three times, and then dry thoroughly, if possible, do a waterproof test, and then use cement and sand, and pave new floor tiles.

2 to 1, 2 bags of yellow sand (in the sand) around the cement, first make up, in the waterproofing, it is best to knock off 2 slotted tiles, so that the waterproof area covers a wide area, it is useful, and the tiles are re-bought 2 stickers. That's it.

To do waterproof first, now there is a good waterproof coating, it is very simple to use, open it and apply it directly, and the building materials store will ask for a small package. Cement and sand 1:2 will do.

You can get 2 experience points, and you can be selected as satisfied with 10 cm, which is a fairly wide slot. Clean the groove first, do waterproofing three times, and then dry it thoroughly, if possible, do the waterproof test, and then use cement and sand, 1:, pave new floor tiles, you can increase experience and wealth at the same time.

10 centimeters, it is a fairly wide groove. Clean the groove first, do waterproof three times, and then dry thoroughly, if possible, do a waterproof test, and then use cement and sand, 1:, pave new floor tiles, you can.

Clean the ditch, mix the waterproof agent with water and cement mortar to paste the tiles, and reduce the amount of water by half according to the instructions. It's easy to do and it's very reliable. Do other waterproofing is unreliable.

10 cm, which is equivalent to a water leak.

Clean the groove first, do waterproofing three times, wait for drying, do a waterproof test if possible, and then use cement and sand, pave new floor tiles, and you're done.

If you are a new house, don't ask, go directly to the developer If you have lived in an old house for a long time, first, you have to dig up the ground backfill part Find the real leakage If you can't find it, you can do a layer of base waterproofing (with asphalt or polypropylene waterproofing) on the backfilled ground Tile If you don't want to be so troublesome, you are in the cracked place Use cement to add cement mortar to repair The specific proportion is not clear Just a little cement Gaza Add water to mix Ensure that the cement is wrapped in sand Don't be too thin Repair the crack in the waterproof Pure hand play Thank you!

Do waterproofing first, and then use cement and sand to make up for it, preferably in a two-to-one ratio.

The ratio of cement to sand is 1 part cement and 3 parts sand. It is best to do it twice waterproof.

It's 10 centimeters long, and if it's 10 centimeters wide, there's no need to make up for it. Under normal circumstances, the surface needs to be cleaned completely. Clean up the original muddy soil.

It is also necessary to remove the surface layer of the mixed soil, and then do waterproof gs or general waterproof materials, do it several times, and then test the water. If it is not leaked, it can be restored with cement and hope to be used.

How deep are you in the groove here, are there any cracks on the structural plate, have you dealt with it, what is the original waterproof method? More information, better advice, free professional technical consultation on concrete waterproof leakage water repair, exempt from repairing today, leaking tomorrow; Repair every year, the trouble of leaking every year.

So why is the water leaking, at least where there are gaps, it is leaking! Before laying bricks, there is no waterproofing, and what is the structure, the waterproofing of many bathrooms is not the same, like our side is a caisson, you have to describe clearly in order to have targeted suggestions.

The 10 cm trough does not use much material, and it is best to fill the store directly without leakage to ensure that there is no leakage.

Toilet waterproof building materials:

1. Pour reinforced concrete floor slabs.

Second, 1:3 cement mortar to find the slope layer, the thinnest part of the 20mm thick, slope to the floor drain, a smoothing.

3. Leibangshi acrylic polymer cement-based waterproof slurry.

Fourth, 30mm thick dry hard cement mortar bonding layer.

There is more moisture in the bathroom, so it is necessary to pay attention to the waterproof treatment during the decoration process, and the waterproof must be in place to avoid the problem of water leakage, and the later maintenance is more troublesome. Secondly, the choice of waterproof coating for the bathroom is also very important, what materials are used for waterproofing in the bathroom? It can be mainly divided into the following types:

1.Cement mortar waterproof materials Cement mortar waterproof materials are common toilet coatings, which should be matched with cement mortar in a certain proportion to form a uniform liquid. When batching, use a stirrer to stir, and slowly add powder for mixing and stirring while stirring (you can add an appropriate amount of water to adjust the viscosity, but it is best to add water before adding powder), and fully stir and disperse to achieve uniform no powder ball, no precipitation, and the prepared material should be used up within 2-3 hours.

2.Polymer polymer waterproof material Polymer polymer waterproof material is composed of a variety of water-based polymers, and then mixed with various additives of high-quality cement, the flexibility of the polymer and the rigidity of the cement are integrated, making it excellent in impermeability and stability. Its advantages are convenient construction, low cost, cost-saving and non-toxic and environmentally friendly.

3.Acrylic toilet waterproof material The biggest advantage of acrylic waterproof coating is that when the paint is applied, the coating will form a conjunctiva, which has strong elasticity and ductility, which is very suitable for use as a toilet waterproof.

And it can be constructed on the wet base layer, with high bond strength, firm combination with the base layer and the outer protective decorative layer, green and environmental protection, no pollution and no peculiar smell. The above three kinds of bathroom waterproof coatings are used more, and the effect is also very good, and it is one of the preferred materials for family bathroom decoration. When carrying out waterproof construction, it is necessary to follow the specific steps, first of all, to level the floor, first use cement mortar to level the ground (especially the house that is re-decorated), and then do waterproof treatment.

Secondly, it is necessary to do a good job in the waterproofing treatment of key parts, and the joints between the wall and the ground, as well as the joints between the water pipes and the ground, are the most prone to water leakage, so the waterproofing of these places must be done meticulously and not sloppily.

First of all, the bathroom is not only small in area and there are many pipes, and more than 80% of the water leakage problems are concentrated in the yin and yang corners, pipes, sanitary ware, and floor drains, so these places need to be paid special attention to when doing waterproofing.

As for the tools needed to do waterproofing, there are generally electric mixers, stiff brushes, scrapers, etc., although it seems that there are not many tools, but it is not recommended that people who have no experience in building construction do it by themselves, because such as the proportion of mixing, the thickness of the brush, the height, etc., still need special attention.

Acrylics.

Water-soluble waterproof material, colorless and odorless, with good elasticity and ductility after conjunctiva, ** more expensive, around 350 yuan.

Cement mortar.

As one of the emerging toilet waterproof materials, cement mortar is currently a very popular bathroom waterproof material. This material is a special adhesive that is used by mixing fine cement and sand ash dust.

Polymers, polymers.

Referred to as JS coating, it has good ductility and elasticity, colorless and odorless, and has good environmental protection. However, at present, this kind of material is relatively high, and the overall price is more than 300 yuan.

Choose according to your needs, and here is an introduction to some common materials.

1. Polyurethane waterproof coatings.

Polyurethane waterproof coating is the most common type of waterproof coating on the market, which is a one-component polyurethane waterproof coating made of isocyanate-based prepolymer formed by addition polymerization reaction of isocyanate and polyether, and mixed with various additives.

2. One-component polyurethane waterproof coating.

The waterproof coating is a reactive flexible waterproof coating, which has good physical properties, strong adhesion, and curing at room temperature and humidity.

3. Non-tar polyurethane waterproof coating.

The waterproof coating is a two-component material, using water as the chain extender, which avoids the toxicity of the amine chain extender, and forms a rubber waterproof layer with elasticity and no joints after curing.

4. Acrylic waterproof coating.

The waterproof coating is made of pure acrylate copolymer or pure propionate emulsion, adding an appropriate amount of high-quality fillers and additives, and is a synthetic resin one-component waterproof coating.