The gas stove at home will not stop when it rings

There may be several reasons why a home gas stove will keep ringing alarms:

The failure of the flame-out protection circuit causes false alarm, and the long beeping sound continues;

Accidental extinguishing of the gas causes the flame-out protection function to be activated;

The flame in the inner ring cannot burn the thermocouple, causing an alarm.

Solutions for the above situations:

When this situation is caused, the flame-out protection device should be replaced in time to ensure that the alarm is activated only when the flame is accidentally turned off;

In the use of gas stoves, try to avoid the overflow of soup and extinguish the fire, and at the same time, pay attention not to use it in a particularly windy environment;

When the flame in the inner ring of the gas stove is small and the induction needle cannot be burned, or the air pressure is too strong, the damper is improperly adjusted, and there is no fire in the middle and the induction needle cannot be burned, an alarm will be issued. This is the basic function of flame-out protection, and the alarm will automatically cut off the gas supply. At this time, it is necessary to adjust the sensor needle to the position where the fire can burn, and at the same time, the damper should be carefully adjusted to ensure that the flame in the middle burns normally.

Notes:The accidental flameout protection device is designed and installed for the safety of the user, so after the failure, do not remove it directly in order to save trouble, which will cause serious safety hazards.

Dear, the gas stove at home is always ringing, and it won't cut off the gas, so it is recommended to find some professional repairmen to repair it, otherwise there will definitely be problems after a long time

1. Check whether there is gas and whether the battery is electric.

If you don't pay attention to check in daily use, it is common to forget to buy gas, when you encounter a gas stove that can't catch fire, you should first check the spark when the gas stove is fired, whether the sound is low and weak, and the discharge frequency is obviously slower than before, if there is no power, please replace the battery in time.

2. Check the air intake of the damper.

Insufficient air intake or improper adjustment of the damper may cause yellow fire and red fire, check the damper under the gas stove, adjust the damper appropriately, and see if there is anything blocking it.

3. Check whether the ignition needle is contaminated.

If the gas stove is left for too long, the ignition needle can easily be soiled by the oil. Clean the ignition needle grease with a dry soft towel while the gas stove is cool, and then try to ignite it.

Is it not in use when there will be a ignition sound, check whether the knob is back, sometimes it will cause ignition all the time if it does not return, and there is the problem of ignition micro switch and connection line sticking, check the line to replace the ignition switch.

The failure of the flame-out protection circuit causes false alarm, and the long beeping sound continues; Accidental extinguishing of the gas causes the flame-out protection function to be activated; Step Reading Inner Ring Flame Unable to Burn the Thermocouple, Causing an Alarm.

The solution when the alarm sound of the gas stove is as follows: when the alarm sound of the gas stove appears for no reason, the fire power of the gas stove can be slightly reduced, so that the problem of the alarm sound of the gas stove can be solved.

Dangerous. Check whether the electronic ignition is broken in time. The coke on the surface of the gas stove was not cleaned in time. The switch button is not reset in time, just change the battery. If there is a short circuit, it needs to be repaired by a professional. <

1. The gas stove electric ignition is always non-stop, but the electronic ignition is broken.

2. Because the coke on the surface of the gas stove was not cleaned in time.

3. The switch button is not reset in time, just change the battery.

4. If there is a short circuit, a professional should repair it.

Check the safety of the gas stove:

1. Conventional methods.

Users generally use soap liquid to detect leaks. Mix soap or laundry detergent with water and apply it to the gas pipe, gas meter hose, and switch in turn. If the soap leaks, it will be blown out of the foam by the leaking gas, and when you see the foam increasing, it is a sign that there is a leak in that part.

After the leak is found, you can temporarily wrap the leak with adhesive tape and then notify the gas company to send someone to repair it.

2. Odorous inspection methods.

If you can smell the smell of gas but do not find the leakage after inspection, it may also be a leak in the underground pipes and equipment, and you should notify the gas company immediately for maintenance.

3. Sensory inspection method.

It can also be detected by seeing, hearing, touching, and smelling.

Sense of smell, household gas is mixed with odorant, and it will smell when it leaks.

Visually, the leakage of gas will cause the formation of foggy white smoke in the air.

Hearing, there will be a hissing sound.

Tactile sensation, the hand is close to the leakage of the hole, there will be a cool feeling.

1. The reason is that the electronic ignition of the gas stove has been damaged, and if it is caused by this reason, it is necessary to replace the new electronic ignition equipment. 2. It is also possible that the gas pipe is blocked or the gas pipe is bent or flattened, and it needs to be cleaned up. 3. Or because the gas stove battery is insufficient, if this situation causes the sound to need to be replaced with a new battery, you can re-ignite.

4. Another reason may be that the gas stove is short-circuited, and you need to find a professional maintenance personnel to deal with it. One situation may be that the gas stove electric lighter is broken, and it is okay to replace it with a new one, or it may be because the coke on the surface of the gas stove has not been cleaned in time, so we usually have to clean the gas stove regularly to maintain a clean cooking environment, and another reason may be because the switch button is not reset in time, just change the battery. It may be because of the gas stove leakage and the gas stove has a sound, we need to turn off the gas stove power, stop the gas stove to continue to operate, so that the gas stove dripping sound will also stop, or it may be because the gas stove's battery is insufficient, when the gas stove's battery is insufficient, the sound of the gas stove ignition will become subtle, and the frequency of the gas stove discharge sound will be significantly slowed down, if this happens, we can replace the new battery to solve the problem of the gas stove has sound.

Another reason is that the flame-out protection device of the gas stove will be ticking when it is activated. In modern society, the newly invented gas stove has a temperature measurement safety device, and we need to wait for the nozzle of the gas stove to reach a certain temperature before it can be stably burned. When we use the gas stove, we can put the pot on the pot first, then hit it, stop for a while and then let go, so that we can light the fire without dripping sound.

Summary. If there is a sound after ignition, it may be due to the following reasons: the battery is low, the ignition sound will be very small, and the frequency of the discharge sound will be much slower than usual, if this is the case, you need to replace the battery with a new one, and then re-ignite.

2.If the ignition sound is crisp and powerful, but there is no fire, it may be that the gas pipe is blocked, and you need to see if the pipe is bent or flattened, and then straighten it out before igniting. 3.

If the fire hole of the stove nozzle or fire cover is blocked, the gas cannot flow out, and it will not catch fire, so you need to remove the air and fire cover, and then use a thin wire or toothpick to dredge it, and then light it again. 4.When the nozzle reaches the corresponding temperature and the pot can be burned smoothly, in this case, you need to put the lid on the pot to ignite, and wait a few seconds to burn.

Hello, there are many reasons why the stove will sound after the gas is used up, for example, the damper may be too open, it may also be that the coal air tank in the gas stove is insufficient, and it may be that the nozzle grinding nozzle on the switch is damaged, or it may be his own quality problem, we have to judge according to our actual situation, and then choose the appropriate method to solve, I hope Xinchong can help everyone.

If there is a lead sound after ignition, it may be due to the following reasons: the battery is low, the ignition sound will be very small, and the frequency of the discharge sound will be much slower than usual, if this is the case, you need to replace the battery with a new one, and then re-ignite. 2.

If the ignition sound is crisp and powerful, but there is no fire, it may be that the gas pipe is blocked, and you need to see if the pipe is bent or flattened, and then straighten it out before igniting. 3.If the fire hole of the stove nozzle or fire cover is blocked, the gas cannot flow out, and it will not catch fire, so you need to remove the air and fire cover, and then use a thin wire or toothpick to dredge it, and then light it again.

4.When the fire nozzle reaches the corresponding temperature, and the pot can be put on smoothly burning, in this case, you need to put the lid on the pot to ignite, and wait a few seconds to burn.

As follows: 1One situation is that the gas stove electric ignition is always non-stop, and the electronic ignition is broken.

2.In the second case, the coke on the surface of the gas stove was not cleaned in time.

3.The three cases are that the switch button is not reset in time, and the battery can be replaced. The four cases should be short circuits, and professionals should repair them.

Please first check whether the white point needle has sparks, if there is no sparks, it means that the discharge needle is leaked and replaced, if there is a spark, it means that the discharge is normal, but the sparks are weak and can not be pointed.

The solution is to adjust the discharge needle backwards, that is, away from the stove, and see if the central fire is not oxygenous, and lower the damper from the stove. At a high altitude, just adjust the damper.

Research and development of gas stoves.

Historically, the first to develop a gas stove was the Frenchman Philippe Ruben, who on September 21, 1799 obtained a patent for a dual-purpose device for gas lighting and heating. The following year, Ruben was in a restaurant in Paris and paid for the equipment himself. Because the gas stove developed by Reuben at that time would emit an unpleasant odor, it was not popular at the beginning and was not promoted.

Despite this, he continued to research and improve this device with great enthusiasm. In 1804, on the day of Napoleon's coronation, Ruben was killed on a street in Paris, and the development of a gas stove was interrupted.

The world's first gas cooktop for stir-frying in the kitchen was invented in 1826 by James Schaff, assistant manager of the British Gas Company in Northampton. He installed the gas stove he invented in his kitchen and used it to cook meat. It is a vertical stove consisting of a hook suspended from the ceiling to hang the meat and a circle-shaped fire vent underneath.

There is no stove for pots.

The first to buy a gas stove was a bus hotel in Leamington, France. In 1834, the bus inn used a gas stove to cook dinner for 100 people, which was not only delicious, but also did not smell of gas, making it an ideal stove. In the summer of 1836, a factory of 35 workers was opened in Northampton, England, specializing in the production of gas stoves.

In 1852, the use of stoves that combined a gas burner and a stove into one began**. In 1915, gas stoves with thermostat control began to appear.

In 1855, the German chemist Bunsen invented a gas combustion device known as the "Bunsen burner", which is a device that contains oxygen and combustible gases to mix and burn to produce high temperatures. Less than a year after the advent of the "Bunsen burner", the British company of Hoddington Anton Smith invented the world's first gaseous fuel domestic heating device. Later, the gradual popularization of gas stoves and the source of coal gas were formed.

The gas stove is turned off, and the stove keeps ringing for the following reasons.

1. The compression spring of the switch is not elastic, or the elasticity is poor, and it cannot be returned to the original;

2. The high-voltage electronic igniter is broken;

3. The contact of the switch is broken and cannot be opened;

4. The solenoid valve is not opened, and the air source does not flow to the fire hole;

5. The thermocouple and the solenoid valve do not form a circuit circuit;

6. The flame-out protection device is damaged.

Here's how to buy a gas stove.

Point 1: Look at the firepower.

The size of the fire is an important performance indicator to measure the quality of a gas stove, if the fire power is not up to standard, there is no way to meet the needs of stir-frying. Here are 3 steps to help you determine how powerful your gas stove is.

Look at whether the heat flow is large. You can look at the brand's promotional leaflet or the brand logo of the bottom shell of the gas stove panel, and the heat flow of the current mainstream brands is from kilowatts to kilowatts;

Point 2: See if the cleaning is convenient.

Look at the panel material. At present, there are three main materials on the market, such as stainless steel, tempered glass, and ceramic, which are relatively easy to clean. The main thing about stainless steel is whether it has non-oil treatment, and if there is, it is more convenient to clean.

Usually the gas stove alarm function is through a thermal sensor to detect the heat source to work, when the gas stove is ignited after normal combustion, the thermal sensor detects the heat source, then it works normally, once the flame is extinguished or the sensor is broken, the heat of the flame can not be detected, it will alarm. It may also be that the voltage is unstable and there is not enough gas. Pay attention to the safety of gas stoves.