Tips for cleaning up blocked refrigerator water holes, how to clean blocked refrigerator drainage ho

It can be dredged by using a general network cable to pass into the sewer hole.

Fill it with a pump or straw.

Spray the ordinary agent and it will pass later.

1 4 Step by Step Reading.

First of all, adjust the temperature of the refrigerator to the middle gear, such as 7 numbers from 1 to 7 are set in the 4th gear, the refrigerator runs for 1 to 2 hours, and observe that all the ice in the refrigerator turns into water.

Take out the contents of the refrigerator, clean up the stagnant water in the refrigerator, especially the water at the drain hole, pour a cup of hot water into the drain hole and pour an appropriate amount, and repeat several times to melt the ice that may remain in the drain hole.

Turn off the power of the refrigerator, wear wire gloves, straighten the wire, and measure the height from the height of the drainage hole to the ground minus about 20 cm is about the length of the drainage hole to the outlet, so as not to insert the wire too long when dredging.

Bend the head of the wire slightly so that it can be smoothly inserted into the thin pipe under the drain hole (there is a slight slope under the drain hole), insert it slowly, if it is blocked, it can be inserted smoothly several times until it is easily inserted into the outlet, and the drain pipe can be finished by dragging it several times. Reset things and boot them up, and you're done.

If you know how to operate the machine, using a positioning cutting machine is faster and more accurate than manual cutting.

When the water outlet hole of the refrigerator is blocked, it often causes a large amount of water to accumulate in the refrigerator. To solve this problem, first unclog the clogged water outlet hole in the refrigerator. If you don't know, the water outlet hole of the fridge freezer and the drain hole of the fridge are both on the back.

Tools Ingredients: cotton swabs or chopsticks.

1.In the daily use of the refrigerator, when a large amount of water is often found on the bottom plate of the refrigerator fresh-keeping cabinet, it may be that the refrigerator outlet hole is blocked.

2.At this time, you can use a dry rag to absorb the stagnant water in the refrigerator first, so as not to get water everywhere in the next step.

3.Once the stagnant water has dried, you can find the outlet hole in the refrigerator. Generally, the water outlet hole of the refrigerator is in the crisper above the refrigerator. Open the crisper and you can find it at the back of the middle level inside.

4.As shown in the figure below, open the fresh-keeping cabinet of the refrigerator, and then remove the items in the middle of the fresh-keeping cabinet, and find that there is a water outlet hole behind it, and there is also a water guide tank at the location of the water outlet hole.

5.Wipe the inside of the sink first. If the water outlet is blocked, slowly use a cotton swab or chopsticks to get the blockage out, and then wipe the hole clean, so that the problem of the refrigerator water outlet blockage is solved.

6.The water outlet hole of the refrigerator should be checked frequently to avoid excessive clogging. After drilling under the hole, it will be troublesome to dredge; In addition, in order to reduce the situation that too much condensation and too much water in the refrigerator can cause mold and clog the water outlet hole, it is usually necessary to drain and empty the items with a lot of water before putting them in.

Always have standing water in the fridge? Clogged drain holes? The cleaning method can be learned as soon as you learn it, and you can easily master it in one minute

Refrigerator drain hole blockage dredging method:

1. Unplug the refrigerator and heat a pot of hot water.

2. Clean the refrigerator room and you can see the drainage holes.

3. Use a screwdriver to open the back cover of the refrigerator, there is a white plastic box in the compressor and a white drainage hole with a length of 1 cm.

4. Wrap the compressor with a plastic bag, seal the bag around the 1 corner below the drainage hole, and connect a basin under the hole.

5. Bend one end of the wire, poke it through the drainage hole in the refrigerator first, if the blockage is not serious, it will be cleared for a while. If it is not passable, the height of the plug can be determined, and then the length of the plug can be determined by poking through the drainage hole below. Unscrew the head of the pump, insert it into the drain hole of the refrigerator to pump in, and plug the gap with a rag, otherwise there will be water flowing out, wipe the water dry with a rag at any time.

Cool the hot water to about 50 degrees, pour it into the drain hole, wait for about 10 minutes, and then poke it with wire. Repeat the seventh step to absorb water, pour hot water in the eighth step, and poke the wire, and it will be pierced within 1 hour. Of course, after turning it on, you have to pour hot water about 3 times (3 cups), and finally screw the back cover, tidy up the refrigerator, and turn on the electricity.

Prevent the refrigerator drain hole from clogging:

Usually in the process of placing food in the refrigerator, we must pay attention to the food should not be placed too much, and at the same time, the food should not be placed next to the wall of the refrigerator, too much food in the refrigerator will not only increase the burden of the refrigerator work, will not help the circulation of air conditioning in the refrigerator, but also very easy to cause food residues to block the drainage hole of the refrigerator.

1. If the blockage of the drainage hole is not serious, you can simply use a thin iron wire. The diameter of the wire to 1 mm can be, too thick can not automatically carry the rock bend, too thin is easy to deform and forceless;

2. If the drainage hole is seriously blocked, you can turn off the power of the refrigerator first, open the door of the freezer and refrigerator room, pull out all the drawers in the freezer, increase the temperature of the box, and slowly dissolve the drain pipe.

3. You can use hot water to flush or blow the drainage hole with a hair dryer to determine the hidden knowledge;

4. Find a special maintenance personnel to deal with it.

1. If the blockage of the drainage hole is not serious, you can simply use a thin iron wire. The diameter of the wire to 1 mm can be, too thick can not automatically turn, too thin is easy to deform and forceless;

2. If the drainage hole is seriously blocked, you can first turn off the power of the refrigerator, open the door of the cold lift disturbance and refrigerator room, pull out all the drawers in the freezer room, increase the temperature of the box, and make the drain pipe slowly melt.

3. You can use hot water to rinse or blow the drainage hole with a hair dryer;

4. Find a special maintenance personnel to deal with it.

The refrigerator is one of the indispensable appliances in our family, in order to maintain the hygiene inside the refrigerator and reduce the growth of bacteria, there will be some water accumulation at the bottom of the refrigerator on a regular basis, so some drainage holes are designed inside the refrigerator to remove these stagnant water. However, if these drainage holes block Lutan, it will affect the use effect of the refrigerator and affect the service life of the refrigerator, so it is very necessary to clean it in time. The following is an introduction to how the water hole in the refrigerator is blocked and how to clean the water hole.

1. The reason for the blockage of the water hole in the refrigerator.

1. Food residues: After putting food into the refrigerator, it is easy to produce dirt and bacteria, and these residues gather into water droplets when they evaporate in the refrigerator to produce water vapor, and after a long time of accumulation, they will be stuck in the drainage hole for a long time, forming a blockage.

2. Dust accumulation is good: During the use of the refrigerator, due to the long-term non-cleaning, dust and debris will accumulate inside the refrigerator, which is also easy to cause the blockage of the drainage hole.

2. How to clean the stagnant holes.

1. Use a vacuum cleaner: First, use a vacuum cleaner to suck the dust around the water accumulation hole, which can avoid bringing dust and dirt into the pipe. And the vacuum cleaner can quickly suck up the debris enclosed in the drain hole.

2. Suck out with a straw: use a straw and gently pinch the upper part (or lower) of the refrigerator drainage hole, and then use the straw at the other end to suck out the dirt and water in the drainage hole, this method is simple and easy, and all the water in the stagnant hole can be drained.

3. Rinse with hot water: In addition, scrub the area around the drainage hole with warm water, which can not only remove dirt, but also kill the bacteria and other microorganisms in the drainage hole, and play a role in disinfection.

In conclusion, it is very important to regularly clean the water holes in the refrigerator and keep the refrigerator hygienic and in good operating condition. If the water holes are not cleaned for a long time, it will affect the service life of the refrigerator and will produce odors, affecting the health of the family. Therefore, it is usually recommended to clean it once a month to avoid blockages of stagnant holes as much as possible.

Here's how to clean it up:Tools Ingredients: round head wire, water.

1. Prepare the round head material.

Prepare a relatively stiff line pipe or iron wire, and make sure that the end of the drainage hole that needs to be protruded vertically into Yu Du Town is smooth.

2. Insert the drainage hole.

After the refrigerator is powered off, put the prepared materials into the drain hole.

3. Insert and take out.

After entering, poke the material to the end, then take out the gear, pour water to test it and reuse it.