The charging of the ant protection board fails to be turned on, and the Bluetooth light of the ant p

Here's how to fix it:

1. Add a parallel equalization circuit to each single battery to achieve the shunt effect, when a battery is fully charged first, the equalization device can prevent it from overcharging and convert excess energy into heat energy, and continue to charge the unfilled battery.

2. Take the voltage parameters of each battery as the equalization object, so that the voltage of each battery is restored to the same, and when the equalization is charged, the capacitor is alternately connected with the adjacent two batteries through the control switch, accepts the charging of the high-voltage battery, and then discharges to the low-voltage battery.

Summary. Activation process 1: The lithium battery you just used generally has residual power, so don't charge it at this time. Put the battery into the product and use it normally until the battery level is low enough to turn on at all.

Activation process 2: the first charge, it is best to use the original charger to charge, and it is better to turn off the charge, many people do not turn off the charge for the convenience of use, which is not conducive to activating the lithium battery capacity. And remind everyone that it should be charged continuously for more than 12 hours and less than 15 hours.

If the prompt is fully charged, unplug it and keep it charged!

Activation process 3: After the first full charge, if it is used normally until it cannot be turned on. You can press Process 2 again to continue the operation!

Activation process four: full discharge, full charge (i.e., repeat process two and process three) repeat three times. At this time, the battery is successfully activated and can reach the best capacity state.

The Bluetooth light of the ant protection board is on, and it cannot be connected.

Dear, hello, Bluetooth connection may not be the following situations: 1 Your phone has a recognition function in the Bluetooth settings Close off and see 2 The connection of the first finger error may be insufficient memory 3 If you are not a copycat machine to dismantle the blind Bluetooth transmission mode error 4 can be equipped with a virus that needs to be flashed. 5. Someone else's password has been set.

Why can't the ant protection board be connected?

Reset the parameters. 1. The ant protection board is directly on the new mobile phone desktop with the high finger accidentally high, and click the ant protection board app to enter. 2. At this time, to open the window of the new wide configuration, you need to find the parameter settings and select Jump.

The main thing is that Bluetooth can't be connected to lithium batteries.

The protective plate can only be linked when it is activated, and you can unscrew the throttle or something.

It's useless to screw it. That reactivates the protection plate.

How to activate. Activation process 1: The lithium battery you just used generally has residual power, so don't charge it at this time.

Put the battery in the product and never return to normal use until the battery level is too low to turn on at all. Activation process 2: the first charge, it is best to use the original charger to charge, and it is better to turn off the charge, many people do not turn off the charge for the convenience of use, which is not conducive to activating the lithium battery capacity.

And remind everyone that it should be charged continuously for more than 12 hours and less than 15 hours. If the prompt is fully charged, unplug it and keep it charged! And pants hunger activation process three:

After the first full charge, if it is used normally, it will be turned on without pure calling. You can press Process 2 again to continue the operation! Activation Process Four:

Fully discharged, fully charged (i.e., repeat process two and process three) repeat three times. At this time, the battery is successfully activated and can reach the best capacity state.

If you don't connect, there is no impact.

Kiss! The resistance discharge on the protection board will heat up, affected by heat dissipation, the size of the protection board, and will not be used to target the resistance with high power, so the balance current is very small, and the discharge is a pure power consumption behavior. It's better to have time to fix it.

Summary. On your phone, tap on the Ant Protection app and enter. Open a new window, find the parameter settings, and select Jump to the next step, no problem, and continue to determine the magnitude of the related object according to the actual situation.

For example, the equalization current size: 180 mA, the reference voltage: , the current sensing range:

440A, starting current: 25A. Once the data has been selected, the result will appear and the setup will be successful.

On your phone, click on the Ant Protection app and enter. Open a new window, find the parameter Set Spring Sell Settings, and select Jump to the next step, no problem, and continue to determine the size of the relevant object according to the actual situation. For example, the size of the equalization current:

180 mA, Reference Voltage: , Current Sensing Range: 440A, Starting Current:

25a。Once the data has been selected, the result will appear and the setup will be successful.

1.Single voltage calibration: You can change the cell voltage value by adjusting the "system reference voltage" (default left and right), and slowly increase and decrease the amplitude until it is accurate!

2.Total voltage calibration: You can change the total voltage by adjusting the "parameter of converting the total voltage AD value to the actual voltage" (the default is about 3330 or so), and slowly adjust the size of the rotten value, until it is accurate!

3.Current calibration: You can adjust the "current sensor range" and slowly adjust the magnitude of this value to change the current until it is accurate!

What is the reason why the total voltage charge is not 100%.

Pro, because the battery is with potential when the protection board acts, the larger the charging current, the higher the battery potential, the greater the battery voltage will fall after the protection of the protection board, and the charge may not be enough. On the contrary, the charging current is small, the battery potential is not too large, and the voltage drop after the action of the protection board is not too loud, and the noise is too large, so the shield may have been overcharged.

Summary. We'll be happy to answer for you.

We'll be happy to answer for you.

Dear, hello, Bluetooth connection may not be the following situations: 1 Your phone has a recognition function in the Bluetooth settings Close off and see 2 The connection of the first finger error may be insufficient memory 3 If you are not a copycat machine to dismantle the blind Bluetooth transmission mode error 4 can be equipped with a virus that needs to be flashed. 5. Someone else's password has been set.

Ask about custom messages].