17 strings of ant protection board parameter settings

Hello, the method of setting up the ant Xingneng protection board is as follows:

180 mA, Reference voltage: , Current Sensing Range: 440 A, Starting Current:

25a4, after selecting the data, the result will appear, and the setting is successful.

Protection Plate Calibration:

1.Single voltage calibration: You can change the cell voltage value by adjusting the "system reference voltage" (the default left and right), and slowly increasing and decreasing the amplitude until it is accurate!

2.Total voltage calibration: You can change the total voltage by adjusting the "parameter of converting the total voltage AD value to the actual voltage" (about 3330 by default), and slowly adjust the size of this value until it is accurate!

3.Current calibration: This can be done by adjusting the "Current Sensor."

range", slowly adjust the size of this value, and you can change the current until it is accurate!

Note: Please do not change the "Power Starting Current" item in the parameter settings, too much may cause the discharge MOS tube to be burned.

Hello, according to what I have learned, the parameter setting of the 17 strings of ant protection board includes the following steps:

2.Open a new window, find the settings, and select Jump.

3.According to the actual situation, determine the magnitude of the relevant object, such as the equalization current, reference voltage, current sensing range, starting current, etc.

4.Once you're set up, click Save.

The above are the parameter setting steps of the 17 strings of ant protection boards, I hope it can help you.

The setting of the ant protection board mainly includes the following steps:

1.First, identify the appliances or equipment that need to be protected. Install the ant protection board on the power cord of the appliance or equipment.

2.Make sure the ant protection board is well connected with the power cord. Wiring with the right tools to ensure good contact and no loose or poor contact.

3.Place the ant protection plate high above the ground. This reduces the likelihood of small insects such as ants getting inside the device. It is recommended to place the ant protection plate 5-10 cm above the ground.

4.Regularly check the working status of the ant protection board. If ants or other insects are found, clean them up and take necessary measures, such as using insect repellent spray or sticky insect paper.

For the setup of the ant protection board, the reasons are as follows:

1.Prevent insects such as ants from entering the inside of the device. Small insects such as ants may enter the interior of electrical appliances or equipment, causing safety hazards such as short circuits, leakage, and even damage to equipment.

The ant protection board can effectively prevent the entry of these insects and protect the normal operation of the equipment.

2.Protect the life and performance of your equipment. When insects such as ants enter the inside of the device, they may leave a corrosive substance on the circuit board, causing a short circuit or damage to the circuit.

The setting of the ant protection board can reduce this risk, prolong the life of the equipment and maintain good performance.

Extended content: In addition to setting up an ant protection board, there are some other ways to prevent ants from invading the device:

1.Maintain a clean environment. Keep the living environment clean, avoid the accumulation of food scraps and garbage, and reduce the chance of ants breeding and entering.

2.Seal food and storage containers. Keep the food tightly sealed in a container to avoid the smell from the food attracting ants.

3.Find and block the path for ants to enter. Carefully observe the ants' movements, find their path into the room, and then seal them, such as using sealants or ant blockers.

To sum up, the wild ambush of the ant protection board can effectively prevent ants and other insects from entering the equipment and protect the safety and performance of the equipment. In addition, the risk of ant infestation can be further reduced by maintaining a clean environment and taking other precautions.

The setting of the ant protection board can be carried out by following the following steps:

Step 1: First, identify the area that needs ant protection and clean up the area. Make sure there are no ants or other insects present.

Step 2: Place the ant protection board around the area that needs to be protected, such as a garden, farmland, or around a building. The protective plate should completely cover the area that needs to be protected.

Step 3: Make sure that the ant protection plate fits snugly against the ground and there are no gaps. Fixtures, such as clips or nails, can be used to secure the protective plate to the ground to ensure security.

Reason explanation: The main purpose of the ant protection board is to prevent the ant's cross-field behavior. When ants are looking for food or resources, they often form a cross-field phenomenon, that is, after an ant finds food, it will release a chemical called pheromones, which attracts other ants to follow, thus forming a long line of ants.

This skewering behavior can cause a large number of ants to congregate in a specific area, causing trouble and damage to farmland, gardens, or buildings. Leather sold.

The setting of the ant protection board can effectively break the string field behavior of ants. The material of the protective plate is usually impermeable, which prevents the spread of pheromones released by the ants, thus preventing the aggregation of ants. In addition, the setting of the protective plate can also provide a physical barrier for the ants to directly enter the area that needs to be protected.

Extended content: In addition to setting up a clever ant protection board, other measures can be taken to control the ant's cross-field behavior. For example, ant agents such as formic acid and ant esters can be used for ant treatment.

In addition, keeping the environment clean and dry, fixing water leaks, removing food debris, etc., can also reduce the attractiveness of ants, thereby reducing the incidence of string fields.

The setting method used by the ant protection board is to install the ant protection board on the wire and cable to prevent the ants from crawling which bend wheel and cause the string wire to fail. The steps are as follows:

2.Clean the installation position: Before installation, the installation position needs to be cleaned to ensure the adhesion effect of the ant protection board. Can be wiped with detergent and kept dry.

3.Paste the ant protection board: Stick the ant protection board to the wires and cables to ensure a firm fit. The appropriate length and width can be selected as needed, ensuring that the area where ants often crawl is covered.

4.Regular inspection and replacement: Ant protection plates usually have a certain service life and need to be inspected and replaced regularly to guarantee their effectiveness.

Setting up ant protection boards in this way can play a role in preventing ants from crawling, preventing ants from building nests on wires and cables, and reducing string failures caused by ants. Ant protection plates usually use a sticky material that sticks to the ants and stops them from continuing to crawl. At the same time, the ant protection board can also prevent ants from gnawing on the insulation layer of wires and cables, thereby prolonging the service life of wires and cables.

In addition, other measures can be taken to further prevent ants from crawling, such as keeping the house clean, eliminating food**, blocking possible entrances, etc. A combination of methods can better protect wires and cables from ants and damage.

The setting of the ant protection board can be carried out by following the following steps:

1.First, identify where you need to set up an ant protection board, usually at the interface of a wire or cable.

2.Fix the ant protection plate on the outside of the wire or cable, making sure it is in close contact with the wire or cable.

3.Make sure that the connecting end of the ant protection board is connected with the ground wire or ground wire to ensure good grounding.

4.Multiple ant protection plates can be set up as needed to cover a larger area.

The ant protection board is set up for the following reasons and extended contents:

1.Prevent ant invasion: The main function of the ant protection board is to prevent ants from entering the wires or cables.

Ants may enter through the interface of the wire, causing damage or short circuiting the wire. By setting up the ant protection board, it can effectively stop the invasion of ants and protect the normal operation of the wire.

2.Protect the safety of wires: If ants get into wires or cables, they may cause safety problems such as short circuits, leakage, and even fires. The setting of the ant protection jujube prototype can effectively prevent this from happening and protect the safe operation of the wire.

3.Improve the life of the wire: Ants getting into the wire or cable may cause damage to the wire, which can shorten the life of the wire. The setting of the ant protection board can reduce the corrosion and damage of ants to the wire, and prolong the service life of the wire.

4.Maintain wire stability: Ant activity in wires or cables may cause loose or poor contact of wires, which can affect the stability and performance of wires. The setting of the ant protection board can effectively maintain the stability of the stool and protect the wires and ensure the normal operation of the wires.

To sum up, the setting of the ant protection board plays an important role in preventing ant intrusion, protecting the safety of the wire, prolonging the service life of the wire, and maintaining the stability of the wire. Depending on the specific situation, the ant protection plate can be set up as needed and ensure that it is properly connected and grounded to achieve the best results.

The setting of the ant protection lead starvation plate drop string can be done by the following steps:

1.First, determine where you need to set up the ant protection board. Typically, these locations can be connection points for cables or wires, grounding devices, etc.

2.Install the ant protection plate at the target location. Make sure it is securely connected to other equipment or components and has good electrical contact with the ground or other grounding devices.

3.Confirm the electrical conductivity of the ant protection board. This is because the ant protection board needs to be able to effectively direct electrical current into the ground to prevent ants from entering the device through cables or cables.

4.For larger devices or systems, it may be necessary to set up multiple ant protection plates to ensure full protection. These protective plates should be distributed around critical connection points to provide better protection.

The ant protection board is set up to prevent ants or other small insects from entering the equipment through cables or cables and causing problems such as short circuits, malfunctions, etc. Ants usually like to seek out humid environments, and their body fluids are electrically conductive, so when ants enter the inside of the device, it can cause a short circuit in the circuit or even cause serious consequences such as fire.

Ant protection plates effectively prevent ants from entering the interior of the device by providing a conductive path that guides ants from the cable or cable underground. These protective plates are usually made of electrically conductive materials, such as copper or aluminum, to ensure good electrical conductivity. In addition, the setting of the ant protection plate also prevents ants from building nests inside the equipment, which reduces the cost of maintenance and repair.

It is important to note that the settings of the ant protection board should be adjusted according to the specific equipment and environmental conditions. Different equipment may require different types and specifications of protective plates, while different environmental conditions may require additional protective measures, such as waterproofing, corrosion protection, etc. Therefore, it is recommended to consult a professional or follow the relevant safety standards and regulations when setting up the ant protection board to ensure the best protection effect and safety.

The setting method used for the string lowering of the ant protection board is as follows: First, place the ant protection board in the position of the circuit series connection to ensure the correct connection. Then, according to the actual situation, select the appropriate string reduction value, usually 10db or 20db, and insert it into the corresponding socket on the ant protection board.

Finally, check that all connections are secure to ensure that the circuit is running stably.

The reason for this is to protect the bridge circuit from excessive crosstalk. In telecommunication transmission, the series of circuits in series causes crosstalk of signals, that is, signals between adjacent circuits interfere with each other. As a kind of crosstalk suppressor, the ant protection board can reduce or eliminate crosstalk interference, improve the transmission quality and stability of the circuit.

The selection of the value of the ant protection board should be carried out according to the specific situation. Generally speaking, if the crosstalk interference is strong, you can choose a higher destringation value, such as 20dB, to better suppress the interference; If the crosstalk interference is weak, you can choose a lower string reduction value, such as 10dB, to maintain the original strength of the signal. In addition, factors such as the characteristics and requirements of the circuit, as well as the compatibility of the equipment, need to be considered.

In practical application, the reasonableness of the string reduction setting of the ant protection board has a great impact on the performance and stability of the circuit. Therefore, it is recommended to set it according to the actual situation and professional guidance to ensure the normal operation of the circuit and the stability of the signal quality.

For the setting of the ant protection board, you can follow the following steps:

1.First, identify the areas that need to be protected, such as wires, cables, etc. indoors.

2.Fix the ant protection plate over the area that needs to be protected. It can be fixed with glue, screws, etc.

3.Make sure there are no gaps between the ant protection plate and the ground or wall to prevent ants from penetrating.

4.Applying anti-ant glue to the ant protection board can effectively stop the crawling of ants.

The purpose of setting up an ant protection plate is to prevent ants from entering a specific area for the following reasons:

First of all, ants may cause damage to wires, cables, etc. They often bite off the insulation of wires, resulting in short circuits in wires or even fires. Therefore, by setting up an ant protection board, it can effectively prevent ants from coming into contact with these wires and cables and protect the safety of electrical equipment.

Second, ants may enter the food storage area and contaminate the food pants. Ants will seek out food and bring it back to the nest, which can cause food to be contaminated with formic acid and bacteria. By setting up ant protection plates, ants can be prevented from entering the food storage area and the hygiene and safety of food can be maintained.

In addition, ants may also cause some damage to the building structure. Ants build nests in walls, floors, etc., which can lead to problems such as cracked walls, loose floors, etc. By setting up ant protection panels, ants can be prevented from entering the building structure and damage to the building can be reduced.

Extended content: In addition to setting up ant protection panels, there are other ways to prevent ant ingress, such as keeping the house clean, fixing water leaks, and cleaning up garbage regularly. In addition, regularly check the status of the ant protection board, and repair and adjust it in time if there is damage or ants bypassing the protection board to ensure that the protection effect is lasting and reliable.