Why does my mouse suddenly fail?

If it is an optical mouse, first see if the contact surface between the laser and the desktop is not easy to reflect, such as glass or plastic surface, it is recommended to use a mouse pad, if it is a rolling ball mouse, open the rolling ball groove below, see if there is a lot of dirt inside, clean it up with tweezers and it should be fine. If it's not one of these problems, it may be a hardware or software problem, as the first floor said, brush the BIOS and see if there is a problem with the interface.

There's a problem with the socket of that mouse.

If it's sure it's broken, just buy one.

This is a problem with the mouse, it is recommended to get a new mouse! The problem can be solved, I have also encountered such a problem, change the mouse everything OK!

I've also had this situation, maybe a temporary functional glitch, and it will be fine after a while.

If you are sure that your mouse is fine, and there has been no such situation before, it is recommended to detach the mouse from somewhere else and try it on your own machine, if it is still the same, refresh the BIOS

The solution to the computer mouse is always out of order.

Reason 1: The mouse pad is uneven.

Solution: Lay out the mouse pad.

When encountering the mouse movement, first check whether the mouse pad is flat. If it is not flattened, it will cause the mouse to move, clean the mouse pad.

Reason 2: The mouse gets into the dust.

Solution: Clean the gray layer in the mouse.

There are gaps in the rolling beads of the mouse, which is easy to enter the ash layer, and if the rolling beads are stuck, it will cause the mouse to move, so you can disassemble the mouse and clean up the lower ash layer.

Reason 3: Something is pressing down on the keyboard or something has fallen into the keys of the keyboard.

Solution: Clean up the keyboard to ensure that the keyboard keys are used normally.

If something presses against the laptop's touchpad or presses down the keys on the keyboard, or something gets stuck in the keys, it will cause the mouse to move.

Reason 3: There are Trojan horses or viruses.

Solution: Use antivirus software to clean up the Trojan and antivirus.

If there is a Trojan horse or virus in the computer, the mouse may be messing around, you can use antivirus software to clean up the Trojan horse and virus.

Reason 5: Whether it is remotely controlled.

Workaround: Turn off remote control.

Sometimes you may choose to allow to be controlled when using remote to solve problems, but forget to end remote control, such as using remote control in QQ, so you can check whether there is a situation where remote is turned on when the mouse is moving.

Reason 6: The mouse driver conflicts with the system.

Solution: Remove the tick from the quick mouse initialization.

Sometimes there may be a conflict with the system, so select Control Panel, find the mouse, and uncheck it before the quick initialization.

Your mouse is an optical mouse, the optical mouse will fail on the mouse pad of some materials, or because of the hot weather, the sweat on the hands on the desktop, the optical mouse will also fail.

1. Reason 1, the cable core is broken, the solution, disassemble the mouse, unplug the cable cable plug from the circuit board, cut the core loss wire by 5 cm according to the position of the broken wire, and then reconnect the mouse core.

2. Reason 2, poor key contact, solution, disassemble the mouse, use an electric soldering iron to remove the left middle button of the mouse, and weld the removed middle button to the left button position.

3. Reason 3, the optical system is dirty, the solution, disassemble the mouse, use anhydrous alcohol to scrub the surface of the light-emitting tube, lens, reflector, and photosensitive tube. The god of the blue.

1. Cause and collapse, the cable core is broken, the solution, disassemble the mouse, unplug the cable cable plug from the circuit board, cut the core wire by 5 cm according to the position of the broken wire, and then reconnect the mouse core.

2. Reason 2, poor key contact, solution, disassemble the mouse, use an electric soldering iron to remove the left middle button of the mouse, and weld the removed middle button to the left button position;

3. Reason 3, the optical system is dirty, the solution, disassemble the mouse, use anhydrous alcohol to scrub the surface of the light-emitting tube, the transparent round mirror and the reflector, and the photosensitive tube.

Landlord,I'm also in your situation.,If you can use it after changing the mouse.,Please tell me.,I'll solve this problem.。 I've been learning to draw SOLIDWORKS these days, and I don't want to be able to use ...... while drawingI hope the landlord will do me a favor! Thank you.

o( o The question is simple. The mouse is too rubbish (it should have been given when I bought the computer, right?) I bought a 20 dollar garbage mouse last time and it's the same situation as you.

Use it and use it all of a sudden to card it and pull out the U disk like a jump and then it's good again. I was depressed when I played Warcraft... Always give me a card.。。。

Give me a chain at a critical moment!! Later, I changed it directly and bought a good !! It is recommended that you also go and buy a similar one.

It's comfortable to use, or go to the computer seller and let him change it for you...

This is called "mouse power failure" and it may be a problem with the host interface, and the main reason is the mouse itself. Let's change it.

Eighty percent is a system problem, it is recommended to redo the system If you have patience, let me tell you the method I often use to clean up my computer:

First of all: use 360 Trojan to kill After completing the cleanup, use the 360 first aid kit to scan: use the malware cleaner and Windows cleanup assistant software to effectively clean up the plug-in and fix system problems.

Finally:Use Windows Optimizer to clean the disk thoroughly once.,And then you can use antivirus software to kill all the viruses If it doesn't work, you can only redo the system.。。。 I do this a lot.

Mouse Problem: Change a mouse.

The shrapnel inside is broken, the elasticity is not enough, and it can't be restored to the original state in time after you click it, so it is recommended to replace it again.

Maybe you don't take too much care of your mouse, and you use it too hard, so you can only replace it with another one.

It's broken, buy another one.