How to open the self locking valve of the gas meter? How to open the gas meter valve

Here's how:1. Open the plug valve by hand, and the direction of the handle needs to be parallel to the direction of the pipeline.

2. Secondly, gently pull the lifting twist up, and it should be pulled to the position of the first-gear switch.

3. Then you can use the gas normally. In the process of opening the gas self-closing valve, it must not be too forceful, otherwise it is easy to cause the lifting torque to be pulled to the position of the second gear switch, resulting in overpressure, so that the gas self-closing valve will be automatically closed, and the gas can not be used continuously. If it is found that the lifting torsion cannot be pulled up, it means that the gas self-closing valve has underpressure, and then it is necessary to find the cause and then take appropriate measures to deal with it.

The battery level of the device may be too low, at this time the valve can be opened by replacing the battery with a new one.

The natural gas meter is in an underpressure state, and you need to contact after-sales service at this time.

If the hardware of the natural gas metering valve is faulty, it is recommended to contact the natural gas operator for repair.

Gas metersThe opening method when the valve is closed.

The natural gas meter shows the specific method of opening the shut-off valve:

1. Long-term no gas: If the valve is closed due to long-term gas use, you can take out the battery in the gas meter, wait about 10 minutes and then install the battery back, and the automatic valve of the gas meter can be opened.

2. Insufficient gas battery: The valve is closed due to insufficient power, and the valve can be opened by hand after replacing the gas meter battery.

3. The gas meter balance is insufficient: If the gas meter is insufficient and the gas valve is closed, you can buy natural gas by offline recharge, and then insert the gas card into the gas meter card slot, and the gas meter valve can be opened.

When opening the gas meter valve, you need to ensure that all gas appliances have been closed. Then, locate the gas meter valve, which is usually located above the gas pipeline, and firmly rotate the valve to a counterclockwise direction until it is fully opened. After opening the gas meter valve, you can open the valve of each gas appliance one by one.

It should be noted that if there is a gas leak in the potato mess, it is necessary to close the gas meter valve immediately and notify the gas company in time for treatment. In order to ensure your safety, please be sure to follow the relevant operating regulations.

Press the solenoid key to open the valve. After installing the battery in the gas meter, you can hear the sound of the gear rolling inside by simply inserting the card, and the word "valve opening" will be displayed on the electronic display. Of course, if the battery of the gas meter is out of power or the gas is in arrears, the solenoid valve will actively cut off the gas source, thus displaying the word "close valve".

1.Which key to press the gas meter to open the valve.

2.The valve can be opened by pressing the solenoid key.

3.Install the battery in the gas meter first, and you can hear the sound of the gear rolling inside by simply inserting the card.

4.At this time, the electronic display of the gas meter will display the words "open the valve".

Hello, I'm glad to answer for you, dear, the opening method of the gas meter self-locking valve is as follows: 1. Long-term unused gas line simple model: long-term no gas use leads to command and close the valve, you can take out the battery in the gas meter, wait about 10 minutes or so and then install the battery back, and the automatic valve of the gas meter can be opened.

2. Insufficient gas battery: The valve is closed due to insufficient power, and the valve can be opened after replacing the gas meter battery. 3. The balance of the gas meter is insufficient

If the gas valve is closed due to insufficient gas meter balance, you can purchase natural gas by offline recharge, and then insert the gas card into the gas meter card slot, and the gas meter valve can be opened.

Hello!The steps to open the gas Kaishen meter self-locking valve are as follows:1

First of all, you need to find the self-locking valve on the gas meter, which is usually located on the front of the gas meter and has a small handle;2.Then you need to pull the handle up, and the direction of pulling up is to pull it towards yourself, that is, to pull it in the direction of yourself;3.Finally, you need to pull the handle to the maximum so that the opening of the self-locking valve can be completedIn addition to the above steps, you can also check whether there is any leakage or damage to the gas meter before opening the self-locking valve Zhaopai door, so as not to cause potential safety hazards.

Gas meter valve opening method: unscrew 90 degrees.

When we use natural gas, we have a valve, if it is in a horizontal state with the pipe beam, it means that the gas valve is open. But if it is vertical, it means that the valve is closed. If it needs to be opened, we only need to open its valve, generally it is a round one, as long as it is unscrewed 90 degrees.

Take a look at your gas meter valves, some may only need to be dialed halfway, and some may have to be dialed all of them. In the handle position of the gas valve, you will see that it has the relevant logo and can be rotated a little. If there is no effect on the rotation, you can ask a professional to repair it.

Proper use of natural gas methods

When using it at ordinary times, it should be noted that gas pipelines also have a certain shelf life, and generally speaking, they should be replaced once every two years, and according to national regulations, the service life cannot exceed two years.

IC card gas meter needs to use batteries, so when using it, we should pay attention to the fact that once the power is low, we must replace the battery in time and prepare four or five batteries. Some gas meters will also give a warning of insufficient power, so you need to pay attention to it when using it.

When using gas for cooking, it is best to open a slit in the kitchen window, which is also conducive to air circulation, and in case of gas leakage, it can also avoid some accidents. After cooking, we should get into the habit of making a good noise, close the valve of the gas stove, and then close the valve of the pipe.

When using IC card gas meter, it is necessary to pay attention to the installation location, and the surrounding area should not be too humid to avoid magnetic fields around, otherwise it will also affect the service life of the gas card.

1.Turn on the power switch on the natural gas meter and check if the power supply is available (if the state width is not available, check the power supply problem). 2.

Check the safety lock on the valve. If there is a safety lock, use the key to unlock it so that the valve can be rotated open. 3.

Locate the valve rotation regulator, switch its adjustment path to the "open" position according to the signs, and if it cannot be operated, check the valve and the internal mechanical adjustment part. 4.Check the natural gas handle to confirm that there is no obvious abnormality, and then rotate the handle to the fully open position with slight force.

5.Confirm safety and turn off the power. In addition, if the valve fails to open, it may be necessary to check the thickness of the gas meter and pipeline.

After confirming that there is no blockage, the pipe can be cleaned by gasket or wire winding, small hammer strike, etc., so that the valve can open normally. In addition, regular maintenance of the valve is also required to maintain good lubrication and surface treatment of the critical parts that can function properly.