What command to use to enter safe mode on the blue screen after the computer is turned on.

1 Press F8 to enter safe mode, the reason for the blue screen is: the computer is not intentionally installed with malware, or malicious programs are generated when surfing the Internet, it is recommended to use 360 Guard, Kingsoft Guardian and other software to clean up garbage, check and kill malware, it may be solved. It really doesn't work, reinstall and restore the system, you can solve the problems caused by the software.

2 If you can't enter the system, you can turn on the system after going to the system selection there press f8 to select the last correct configuration and security mode that works, and you may be able to enter the system.

3-point Start Menu Run Enter cmd and enter it at the Command Prompt.

for %1 in (%windir%\system32\*.dll) do s %1 and then Enter. Then let him run it and it should be solved.

4 Recently, the computer has been poisoned, unstable software has been installed, etc., it is recommended to take a full antivirus, uninstall the software that caused the problem, and reinstall another version, which may be solved. No more, it's OK to reinstall the system

5 If the memory module in the computer case is dusty, disassemble the case, remove the memory module, clean the memory gold finger, and reinstall it.

6. If the memory of the computer is bad for a long time, the parallel memory is bought, and the multiple memories are incompatible when used together, etc., it is recommended to replace the memory to solve the problem.

7 The computer has been used for a long time, the hard disk is broken, and the logical bad sectors can be repaired by repartitioning and installing the system, but it still doesn't work, then it's time to change the hard disk, and it can be solved by changing the hard disk.

The computer blue screen can't enter safe mode.

Disassemble the computer case, discharge the motherboard, remove the electronics in the motherboard for 10 minutes, and then put it back on.

TRL+ALT+DEL to enter the motherboard settings.

Restore the BIOS to its default state first and see if it resolves.

Then, boot press F8 for one last correct configuration attempt.

The computer boots up with a blue screen **stop): 0x000000ed, cannot enter the operating system. How to solve the blue screen** is 0x000000ed computer blue screen problem?

1. Left-click and double-click: Blue Screen Assistant (in the Rubik's Cube of the soft media) icon.

2. In the open BSOD Assistant dialog box, click: **Query, and then enter the last two digits of the blue screen**, such as: ED, click: Query.

3. In the Blue Screen Assistant window, you can see the cause of the failure: it is generally caused by an error on the disk. Check whether the hard disk connection is not in good contact or whether the hard disk cable does not meet the specifications.

If there is no problem with the hard drive cable, you can enter safe mode to fix the hard drive error.

4. Enter the safe mode to repair the hard disk: Restart the computer and press (i.e., press once, stop once, but fast) F8 to enter the safe mode with command prompt.

5. When the computer enters the safe mode with command prompt, click Start-Run and enter cmd, press Enter, open the Administrator Command Prompt window, enter the chkdsk r command, and press Enter.

6. If you can't open the administrator command prompt window according to the above method, click My Computer - C: Windows - System 32 - Right-click: and left-click in the right-click menu:

Run (a) as administrator, enter the chkdsk r command in the admin command prompt window that opens, and press enter.

8. Restart the computer and repair the hard disk. If the problem persists after the repair or an error is prompted during the repair, you should consider replacing the hard drive.

9. The above is: to solve the blue screen ** is the way to 0x000000ed the blue screen problem of the computer, and other blue screen ** can also be queried with the blue screen assistant to find out the cause of the fault and the solution.

The blue screen of a computer is caused by a hardware failure or a faulty hardware driver. In safe mode, some hardware drivers are not loaded and running properly, so there will be a blue screen.

Based on the blue screen**, you can search for workarounds.

Hello dear <> my answer is as follows, please be patient and take a look at the <>

When the computer is blue screen and enters safe mode, you can try the following to fix the problem:1Restart your computer

First, try restarting your computer. When there is a suspicion, restarting can fix the temporary problem of the celery shed and restore normal operation. 2.

Follow the prompts to select an earlier backup point to restore the system to that point in time. 3.Disable the driver that is causing the problem:

Sometimes, the blue screen error can be caused by a driver conflict. In Rest mode, you can try disabling recently installed drivers. Open"Device Manager", find the recently installed device drivers, and disable them.

Restart your PC and see if the problem is resolved. 4.Perform a virus scan:

The blue screen error can also be related to a malware or virus infection. In safe mode, use a reliable antivirus software to run a full scan to remove any viruses or malware. 5.

Update drivers and operating system: Make sure that your operating system and drivers are all up to date. In Safe Mode, you can access the manufacturer's official **,** and install the latest drivers and operating system updates.

Cause: There is an error in the partition table of the hard filial piety Zheng rough disk.

Workaround: Repartition the hard drive.

Here's how:

Make the U disk into an installer PE to start the U disk.

Insert the prepared installer PE boot USB flash drive into the blue screen computer, and set the computer to boot from the USB flash drive.

Start from the U disk, enter the main menu of the installer PE, select 03 or 08pe to enter the PE desktop to open the desktop Diskgenius partition management tool, select the hard disk you want to repartition, click the right button, and select Delete all partitions, as shown below:

Select the hard disk you want to repartition again, right-click, select the conversion partition table type to MBR format (if you want to install the ghsot system, choose this, but this is a non-UEFI start), if you want UEFI to install the system and UEFI to start, you can right-click again, select the conversion partition table type to GUID format (only the original version or the installed version of the system can be installed) as shown below, note that all the data on the hard disk will be lost during the conversion process, please pay attention to the backup.

After the conversion is completed, the hard disk is partitioned quickly, and the partition table is the partition of the MBR type, as shown in the following figure.

After the <> is divided, it will be connected to the automatic formatting, and then you can install the system, and then there will be no more blue screen phenomenon in the installation.