If the network cable is not enabled, you can plug in the router

There are 2 ways to use a mobile phone to set up a wireless router to surf the Internet, one is to set up the parameters through someone else's computer, and the second is to use the mobile phone to complete the settings yourself, the following is the specific operation method:

1. First of all, we plug in the power supply of the router, and then connect the network cable to the card slot of the WAN, at this time, the WAN light on the router layout will flash, which proves that there is a signal source.

3. Click Connect.

4. Because the wireless network is not encrypted, you can see that it is connected. Now it's time for how to set up a router to surf the Internet.

5. Open the browser of the mobile phone, it is best to use the browser of the mainstream point, enter the IP address of the router in the address bar, this address can be seen on the back of the router, click to enter.

6. Then enter the router username and router login password in the router login box, and click OK. (The username and password can also be found on the back of the router, if you don't have one, you can read the manual).

7. The next step is to set the parameters for the router to connect to the network

1) Select the access type and check PPPoE.

2) Enter the broadband and broadband password given to you by the broadband provider;

3) In the wireless encryption status, check Encryption, fill in the wireless password by yourself, and click Save to take effect.

The router will reboot for the settings to take effect. And the wireless connection of the phone will be disconnected because the connection password is incorrect.

In the settings and WLAN settings of the mobile phone, reset the connection password, and you can connect to the Internet normally.

Yes, but can it be used?

Possible reasons why the wireless router cannot connect to the network: The port cable is looseSolution: Reconnect the wireless router WAN port network cable.

2.Dialing Exception Solution: Check whether the dial-up account password is correct, and change it if it is incorrect.

If correct, consult the network provider to remotely monitor whether the line is working and whether the broadband account is in arrears or expired. Extension: How to configure a wireless router:

1.Connect the wireless router to a higher-level network device (e.g., modem, first-level router). Connect the WAN port of the router with the LAN port of the higher-level network device with a network cable, and the connection is successful when the WAN port light flashes on the router.

The first time you use the router, you generally don't need to enter the wifi password. 3.Go to the wireless gateway configuration page.

Open a browser, enter the IP address of the router gateway (usually, the default value is located on the nameplate on the back of the router) to enter the gateway configuration page. (The new route will generally pop up this interface automatically)4Set up a wireless router to access the Internet.

Go to the WAN port settings in Advanced settings. If the broadband service requires dial-up, select PPPoE dial-up, otherwise you can choose DHCP to get automatically. To dial up PPPoE, enter the broadband password, and select Automatic connection as the connection mode.

If DHCP is automatically obtained, you do not need to enter this field. 5.Set the wifi name and wifi password.

Go to Wireless Security in the Wireless Settings and select WPA2-PSK mode for Security Mode. Select AES for WPA encryption rule. Set up a wireless network key.

6.After the setting is completed, the router will automatically restart, please enter the new wifi password to connect, and you can access the network.

Wireless routers.

A plugged network cable is required.

Before configuring a wireless router, you must connect your PC to the wireless router with a network cable, and the other end of the network cable must be connected to the LAN port of the wireless router. After the physical connection is installed, in order to configure the wireless router, you must also know two parameters, one is the username of the wireless router.

and passwords; Another parameter is the management IP of the wireless router.

The default management IP of the wireless router is or other), the username and password are admin.

Normally, it is not plugged in to the network, but the router needs to be set up:

Here's how to do it: 1. You need to connect the router to the computer with a network cable;

2. Enter the IP address of the router on the computer, generally 3. Log in to the router interface, and the login password is lowercase admin;

4. Find the WAN option, select PPPoE in it, and then enter the broadband account number and password to confirm;

5. You can set the wireless network in the wireless network setting option, and enter the SSID is your wifi name, which is encrypted;

6. Click "Restart Router" in the system tools or other options, wait for a while to restart, and then you can surf the Internet.