How to connect the router to the network cable, how to connect the broadband network cable to the ro

Prepare two network cables (the first one you have ready, which is the one that goes through the "modem").

The second is to buy a network cable sent by the router, if you don't send it, you have to make a network cable with crystal heads at both ends. ）

1.Change the local connection to automatically obtain the IP address.

2.The network cable from the "modem" (modem) is connected to the "wan" port on the router, and the router's ports 1, 2, 3, and 4 are connected to the network cable port behind the computer host.

3.Open the browser and enter the password and username of the router are admin

4.Go to the router settings screen, select the PPPoE (ADSL virtual dialing) method, enter your home account and password, and confirm.

5.Then set the SSID, encryption method, and password. Save, restart.

6.In the end, the setup is considered successful.

There should be a manual for routing! There are quite a few steps to do this.

1. First let the router face the external network, first of all, what type of Internet access is your network, ADSL dial-up, DHCP automatic acquisition, fixed IP, etc. However, it is generally adsl dial-up, and if you have a network card at home, it is generally dial-up, and there is an account number and password on the card, and you can enter it first to connect the router to the Internet.

If you don't understand, it's best to find someone who knows a little bit about the Internet to help you get it.

See if the router is set up, see the wireless signal in the WLAN of the mobile phone, connect it and enter the password.

You can connect the broadband network cable directly to the computer or connect the broadband to the router and then connect the computer through the router, and you can connect to the Internet with the corresponding settings, specifically taking the broadband direct connection to the computer as an example. Here's how to set up the connection

1. Connect the broadband network cable directly to the computer, then click Start in the lower left corner of the computer, and select the control panel to enter.

2. Click Network & Sharing Center in the open control panel interface to enter.

3. Click Set up a new connection or network entry in the Network & Sharing Center interface that appears.

4. In the dialog box that appears, select Connect to the Internet and click Next.

5. After the page jumps, select Create a new connection, you can see that the connection method is PPPoE, click Next.

6. In the interface that appears, you can see the connection method of broadband dialing, click to enter.

7. After the page jumps, enter the Internet access and password provided by the network service provider and click Connect.

8. At this time, you can see that the computer is dialing up to connect to the network.

9. After waiting for a while, you can see the prompt that the network connection is successful that pops up on the page, and click Connect Now to use the network.

10. At this time, you can see the sign of broadband network connection in the lower right corner of the computer, that is, the dial-up Internet access has been completed through the computer.

Method (1).

1. Hardware connection: Connect any network port of the optical modem with the WLAN port of the wireless router with a network cable, and if other computers in the LAN need to access the Internet through wire, you can connect the network of the computer to the LAN port of the wireless router through the network cable.

2. Re-set the IP address of the router. Open a browser on the computer connected to the router, enter the control address on the router side and press enter, find "Network Settings" and "LAN Port Settings, Reset the IP of the Router" in the page that opens, and then click "Save" to complete the IP address setting of the router.

3. Find "Network Settings" and "WAN Port Settings" in the page that opens, reset the "WAN Port Connection Type" of the router to "PPPoE" mode, then enter the Internet account and password, check the "Dial on Demand" mode, and click "Save" to complete the WAN settings of the router.

4. In the page that opens, find "DHCP Server" and "DHCP Service", select Enable DHCP Server, and set the address at the beginning of the address pool to ", and set the address at the end of the address pool to "and click "Save" to complete the DHCP setting of the router.

5. Finally configure each device connected to the wireless router. You can configure the IP address acquisition method to be obtained automatically.

Method (2) 1, firstly, the network cable on the modem (modem) end and the WAN interface on the router (this interface is usually different in color or position from several other interfaces with the same appearance) as shown in the figure

Note: For example, some community broadband and other network cables directly enter the home without modem connection network connection mode, and directly connect this network cable to the WAN interface.

2. Prepare another network cable to connect to any of the 4 LAN ports (the yellow interface in the figure below), and connect the other end to the computer network port. (Skip if using wireless).

3. Connect the modem and the power cord of the router, turn on the switch (some brand devices will start automatically after connection, no switch), and the hardware connection of the above router will be completed.

Now is the age of network information, and our lives are inseparable from the Internet. The network cable and router are one of the connection devices of the network, if the network cable is not connected, the network will not be able to connect to the network, so how to connect the network cable to the router? Let's take a look at the relevant knowledge.

1. How to connect the network cable to the router.

First, enter the address of the router management page in the address bar of the browser, enter the user name and password, and log in to the settings interface; See the settings interface of the router, click the wizard on the left, select Next on the right interface, select the Internet access method, and fill in the broadband account and password; Then set the SSID name and select WPA-PSK WPA2-PSK to set the PSK password. Click Finish and restart to try it, if the WAN port shows that it is connected, it proves that the connection is successful.

Second, how to connect the network cable at home.

1. First of all, prepare the tools, choose the appropriate network cable according to personal needs, with a crystal head, a crimping caliper, and a network cable connection tester.

2. Peel off the skin at both ends of the network cable with the crimping caliper, and then smooth the wire core according to the standard order. Arrange the cores in order, place them at the crimping pliers, cut the cores in the network cable flat, and pay attention to leaving a certain core length.

3. Put the prepared double talk filial piety stranded wire in the RJ45 crystal head, and pay attention to the balance of strength in the process of placement until the end. Then check that the 8 cores are completely neatly arranged in the crystal head.

4. Place the crystal head and press it hard, and then pull it out.

5. In this way, the network cable on one side is connected, and then the other end can be completed in the same way. After the two ends are installed, test whether the light is on, if the light is not on, it means that there is a problem with the core connection and you need to re-operate.

Conclusion of the article: The relevant knowledge of how to connect the router with a network cable will be introduced to you here, I hope it will be helpful to you. If you want to know more about related knowledge, please continue to pay attention to Qeeka Home Information Pingbi Reputation Desk, and more exciting content will be presented to you in the future.

Enter the area and get the decoration for free**].

In our daily life, many people will install various different types of routers in their homes, so how do the routers connect to the network cable? Today I will tell you how to connect the network cable to the router, I hope it can help you, interested friends can follow to learn about it. 1. How to connect the network cable to the router 1. If the network cable is connected to the router, one end of the network cable is connected to the optical modem first, and then the other end is connected to the WAN port of the router.

2. If the network cable is connected to the computer, then we first connect one end of the network cable with the computer's equipment, and the other end with the LAN port of the router. 3. If the user can't access the Internet normally after connecting to wifi, generally only need to restart the router to solve the problem. 4. If Zhaoye wants to reset or change the router password, you can log in to the relevant settings and press and hold the reset button behind the router to reset the router, and after the password, we can log in according to the row behind the router**, and the initial password setting can be shouted after logging in.

2. Precautions for using routers 1. When we use the router, it is best to restart the router twice a week, and a router is in a closed state for a long time, which is likely to damage the signal light of the router. 2. The router is sometimes a hardware device that connects two or more networks, so when we buy a router, it is best to buy some better brands and well-known routers, and burn them together to extend the life of the router and do not need to replace the router frequently. The above is a summary of the relevant content and information about how to connect the network cable to the router, I hope it can help you, if you have other questions, you can leave a message below the platform, and you will solve the problem in time.

Finally, if you have any questions about home furnishing or home decoration, you can pay more attention to Qeeka Home.

Do the math how much it will cost you to renovate your home

The steps to connect the network cable to the router are as follows:1Confirm that both the router and the network cable are turned off.

2.Plug one end into the WAN port of the router, which is usually located on the back of the router with a port labeled "WAN". If your router does not have a WAN port, you can choose any of the LAN ports, which are usually marked with numbers such as "LAN" or .

3.Plug the other end into the network port of your computer, network device, or broadband modem. If you want to connect multiple devices, you need to use a switch or network hub to assign network cables to multiple flushing devices.

4.Next, connect your router to your broadband modem. Use another network cable to connect the broadband modem to the WAN port of the router.

This will enable the router to receive an internet signal. 5.Finally, turn on your router and broadband modem and wait for them to boot up.

This may take a few minutes. Once booted up, your device is ready to connect to the internet through your router. It is important to note that before connecting your router to the network cable, you need to make sure that your ISP has provided you with Internet service and that you have installed a broadband modem.

Summary. 1. First of all, plug one end of the network cable into the LAN port of the router (usually yellow), and the other end into the network interface of the computer (usually blue).

Pro, the network cable and router connection method is as follows:

1. First of all, plug one end of the network cable into the LAN port of the router (usually yellow), and the other end into the network interface of the computer (usually blue).

2. Check whether the power supply of the router has been plugged in and confirm that the router has been turned on.

3. Open the computer group and enter the network to set up the collapse and balance interface. In the network settings, find the "Ethernet" option, click on "Settings", and select "Automatically get IP address".

4. Let the loser confirm that the network connection has been established. You can log in and set up your router by opening the Browse Adjuster and entering the default for your router.

The above is a general way to connect a network cable and a router, and the specific operation may vary depending on the brand and model.