What happened to the appearance of E2 in the electric ceramic stove?

Corresponds to your own electric ceramic stove.

brand, the corresponding question has different meanings. The E2 problems of different brands of electric ceramic stoves are as follows:

Galanz induction cooker.

The display E2 represents the power supply overvoltage (250 volts), and the Midea induction furnace E2 displays the main sensor short circuit, Combo.

The induction cooker E2 indicates an open or short circuit to the pan bottom sensor, Supor.

Induction cooker E2 indicates IGBT power tube overheating protection, and Pentium electric cooker E2 indicates short circuit of its main sensor.

Sanyo induction cooker shows E2, poor heat dissipation inside the machine, or internal temperature sensor.

Fault, you can look at the warranty card after finding the problem, whether it is within the warranty period, it is recommended to call ** to customer service, do not easily choose a small household appliance repair station.

Corresponding to your brand, it is different for the question. Here are a few examples.

Galanz Induction Cooker E2 means Power Overvoltage (250V) Midea Induction Cooker E2 means Short Circuit Main Sensor Bad.

Combo Induction Cooker E2 means Pot bottom sensor open circuit, short circuit Supor Induction Cooker E2 means IGBT power tube overheating protection.

The Pentium induction cooker E2 indicates a short circuit in the main sensor.

The Sanyo Induction Cooker E2 indicates that the internal heat dissipation of the machine is not smooth or the temperature sensor inside the machine is faulty.

Libang induction cooker fault** e2: The power supply voltage is too low. Two long and three piccolo sound alarms.

Ringing twice to turn into standby. (5 seconds interval).Midland induction cooker automatic protection error screen display**:

E---2 IGBT temperature sensor open circuit or undertemperature protection.

AUCMA induction cooker shows that the temperature of the E2 IGBT exceeds 85 and lasts for 3s before the internal temperature of the induction cooker cools down before turning it on.

Supor Induction Cooker Common Faults** E2 IGBT Power Tube Overheating ProtectionMidea Electronic Magnetic Cooker EP181 EP201 E02 Short Circuit (Main Sensor Bad).

Dear, I'm glad to answer for you: what is the fault of the electric ceramic stove that will show E3 when it is heated? Answer; The electric ceramic vertical elimination furnace will be heated and the E3 will be displayed as a fault, as follows

1. The temperature probe is damaged. 2. It is manifested as being unable to start when plugging in the electric knowledge source, no matter after pressing the open child lock key, and then pressing the power switch bridge, the display panel prompts: E3, accompanied by the sound of Didi flashing.

Due to the damage of the temperature probe, the system could not detect the temperature, so in order to protect other components, the starting power supply had to be disconnected, and the E3 system setting prompt was displayed, and the drip warning was delayed. Even if the power is plugged in and does not make any action, within three seconds, the system will automatically cut off all button functions and display a warning. 3, the exclusion method can only replace the temperature of the probe parts, this part of the parts is estimated to be inexpensive, whether the electrical appliances are under warranty or over-warranty, it is recommended that you contact the original manufacturer for maintenance, there is a certain guarantee in safety.

Hello, dear and happy, I am honored to answer for you. What is the fault of the electric ceramic stove display E5Answer: The failure of different brands of induction cooker is different.

1. Galanz C20--H8B fault**, E5-stove sensor short circuit. 2. Joyoung induction cooker failure**, E5 - ceramic plate temperature sensor is broken. 3. Libang induction cooker is faulty, E5-VCE is too high, and it is re-tested to start.

4. Meilian induction cooker macro section automatic protection error screen Shen Hall display**, E5 - cooktop temperature sensor short circuit or excessive temperature protection. E5 is one of them, the working voltage of the induction cooker is too low, the IGBT temperature is too high, the stove sensor is wrong, etc. After clarifying the cause of the appearance of E5, as long as the symptoms are correct, the induction cooker can be restored to normal.

First of all, we need to check the furnace surface temperature sensor of the induction cooker, if we find that there is a problem with the stove surface temperature sensor, we need to replace the stove surface temperature sensor of the same scale immediately, and start the induction cooker again after installation, and we will find that the induction cooker is working normally.

1. Water pressure problem

When the water pressure is too low, the water heater often fails to start properly. Of course, the water inlet of the water heater has a filter. Workaround: Just clean it up at this point.

2. Failure of water-gas linkage device

The failure of the water-gas linkage device generally includes the following two aspects: first, the tympanic membrane in the water-gas linkage valve is aging or damaged, and the micro switch cannot be pressed; Second, the micro switch is broken. Solution: Replace the switch directly.

3. Solenoid valve failure

This is a very common type of failure. Generally, there are two types of solenoid valve failures: damage and aging. For example, it can be ignited when it is ignited, but it will turn off immediately. If it's damaged, it's not possible at all. Solution: Replace the solenoid valve.

4. Power supply problems

The power supply problem, strictly speaking, is not a problem, as long as you pay attention to yourself, but it is a problem that can be easily overlooked. Solution: This one is very simple, just check whether the indicator light of the AC power plug is on.

e should be the abbreviation of error, that is, error, and it is not easy to display in Chinese; 5 is the fifth type, so it's not easy to repair......

1. Solenoid valve failure.

This is a very common kind of failure, usually the solenoid valve failure includes two kinds, damage and aging, such as when ignition, it can be ignited, but it will be extinguished immediately, and if it is damaged, it cannot be at all. Solution: Replace the solenoid valve.

2. Power supply problems.

The power supply problem, strictly speaking, is not a problem, as long as you pay attention to it, but it is a problem that people can easily ignore. Solution: This one is very simple, you just need to check whether the AC power plug indicator is on.

3. Water pressure problem.

When the water pressure is too low, the water heater often fails to start normally, of course, there will be a filter screen at the inlet of the water heater, and if the blocked water cannot flow normally, it will not be lit. Solution: At this time, just clean it up.

4. Failure of water-gas linkage device.

1. The tympanic membrane in the water-gas linkage valve is aging or damaged, and the micro switch cannot be pushed; Clause.

Second, the micro switch is broken. Solution: Replace the switch directly.

I repaired Joyoung's electric ceramic furnace showing that the E5 was faulty, and the reason was that the power tube temperature sensor on the board was open circuit.

The induction cooker will be shut down after heating for a while, and the fault will be displayed **e5, and novices can get it in minutes.

Generally, it is a temperature-related sensor failure, and the brand is different, and there will be a gap, look at the manual.

What does it mean when e2 appears in the electric ceramic furnace How to deal with your dear, the electric ceramic furnace shows that e2 represents the overvoltage of the power supply. Solution: 1. Install a special power cord and power socket.

Due to the high power of the induction cooker, the power cord and socket must be configured according to the power of the town. Generally, the copper core wire that can withstand 15A current should be selected, and the sockets, plugs, and switches used should also meet this requirement. Otherwise, the large current during the cautious and rough operation of the induction cooker wheel will cause the wires, sockets, etc. to burn and short-circuit.

I hope my answer is helpful to you, and finally I wish you good health and a happy mood again!

How to solve the induction cooker display e2:

1. If E2 is displayed after a break in work, it may be that the ambient temperature is too high, causing the internal temperature to be too high and the protection is shut down, or the air inlet and outlet are blocked, resulting in poor heat dissipation.

2. If E2 is displayed immediately after booting, it may be that the thermostat socket falls off, or there is a problem with some circuits of the thermostat due to the fact that the internal temperature ratio of the machine has not been reduced after the dry burning protection of the machine.

3. Most of the E2 faults include the problem of the circuit board, based on the consideration of electricity safety, it is recommended not to replace the components and repair them by themselves, and find after-sales or professional maintenance personnel to check and repair.

Precautions: 1. Place it flat. The table top where the induction cooker is placed should be flat, especially when eating liquid hand hot pot on the dining table. If the table top is uneven, so that one foot of the cooker hangs in the air, the gravity of the pot will force the stove to change forcibly when it is used.

2. Ensure that the pores are unobstructed. The induction cooker in work heats up as the pot heats up. Therefore, when placing an induction cooker in the kitchen, it should be ensured that there is no object blocking the inlet and exhaust holes of the furnace body.

It is only possible that the ambient temperature around is too high.

As soon as the electric ceramic furnace is turned on, E3 is displayed, what is the fault?

Dear, hello, I'm glad to answer for you, the electric ceramic stove will display e3 as soon as it is turned on, what is the fault? Answer: This is a very common kind of fault, usually electromagnetic rotten valve failure includes two kinds, damage and old hunger and noisy, such as when ignition, can be ignited, but immediately will go out, damage is not at all.

Solution: Replace the solenoid valve. Electric ceramic furnace fault comparison table E01 Open circuit (main sensor bad) E02 Short circuit (main sensor bad) E03 High temperature (main sensor bad) E04 Open circuit (heat sink sensor bad) E05 Short circuit (heat sink sensor bad) E06 High temperature (heat sink sensor bad) E07 Low voltage protection E08 High voltage protection E10 Dry burning protection E11 The main sensor is bad, and the electric ceramic furnace has an E3 fault, which is generally due to the voltage accepted by the electric ceramic furnace is too high. As a result, the heating wire or heating plate inside cannot work normally.

The E3 alarm is a kind of high voltage protection, and its purpose is to prevent the thermistor branch from opening and causing temperature runaway. Induction cooktops will only work properly if the voltage is between 175-285V. When the mains sampling circuit component fails or leaks, it will be detected by the CPU and an E3 alarm will be displayed.