How to prevent the paint of the tombstone from falling off, and what are the skills of painting the

1.When choosing a tombstone, try to choose a tombstone with good quality and a thick paint layer.

2.Keep the tombstone dry and clean to avoid damage to the paint layer caused by moisture and dirt.

3.Regular maintenance and upkeep of the tombstone, including cleaning, waxing, etc., can effectively prevent the paint layer from peeling off.

4.If you find that the paint on the tombstone is peeling off, you can repair it in time to avoid the problem from expanding.

In general, in order to prevent the tombstone paint from falling off, it is necessary to pay attention to maintenance and maintenance, and try to avoid using too sharp tools or chemical agents to contact the surface of the tombstone, so as not to cause damage to the paint layer. If the problem is more serious, you can consider asking a professional maintenance personnel to fix it.

Reasons for the word paint to fall off:

1. The lower surface is polluted by wax, grease, silicone, oil, release agent, water, rust or soapy water.

2. No surface treatment agent is used on the substrate surface, or the type of treatment agent used is incorrect.

3. The substrate surface adhesion is insufficient.

4. When painting, the surface temperature of the substrate is too high or too low.

5. The method of spraying the primer is improper, and the primer is not fully dried.

6. The viscosity of the paint is not appropriate, the type of thinner material used is not right or the quality is too poor, and the pressure of the compressed air is too high.

7. The paint film is too thick.

8. There is internal stress between two adjacent layers of paint film.

It's time for Qingming. Remove the original paint with a cleaning ball, and then go to buy special paint for the car, put some thinner water on it, so that the paint is not too viscous, and apply it with a brush, and try not to be too viscous. Wait until it is dry and apply it again, this will prolong the time for the paint to come off, and it is impossible for you to keep the paint from coming off.

Besides, Qingming is a day of tomb sweeping, what is tomb sweeping? Isn't it okay for you to just go to the tombstone and look at it?

Sprinkle your own essence every day to ensure that it will not be damaged for 10,000 years.

1. The surface of the stele is polished with a motor cloth wheel.

2. Writing or printing on the stele.

3. Chisel and engrave stone inscriptions.

4. The side of the stone tablet inscription is coated with hot melt paraffin.

5. Directly apply the gold pigment to the concave word (the color pigment can be adjusted by itself, and the formula is: epoxy polyester gold powder curing agent.

6. Use a shovel to remove the residual pigment around the word because there are stone errors around the word, so the pigment will not stick to the stone, and there will be no shovel.

Hello, 1, do a good job of protection black stone is susceptible to dust, pigment and other substances pollution, should do a good job of protection 2, grinding optimization to do a good job of black stone grinding optimization stage 150 or 200, need to continue to cross grinding more than 3 times, the more times the more uniform, the clearer the background color of the stone will be. 3. Prevent scratches During construction, prevent the sand or hard objects brought by external factors from scratching the ground. Clean up the mud on the site and the mud of the machine itself in time to prevent the debris from scratching the ground, and keep the ground clean at a high level.

Prevent scratches on the grinding disc with coarse grains. Solution: When grinding, if it is found that there are protruding particles on the grinding disc, use a needle or blade to remove it.

The surface treatment of stone is an important form of stone treatment, so what is the specific situation? 1) The ground should be thoroughly cleaned and kept clean before crystal plane treatment. 2) Choose a heavier crystal surface processing machine, such as Weiba brand AN17SC or VF17HD, the weight of the general floor brusher is not suitable for this work.

The weight, power and speed of the machine, as well as the right amount of chemicals, are essential to achieve good results.

Summary. With ink and rice paper, you can distinguish and see the inscription clearly; Prepare ink, rice paper, plates, brushes, cloth bags and other materials and tools, first brush the mud and dust of the stele clean, pour the ink into the plate, use a tied cloth bag, dip the ink evenly on the tablet surface, and then cover the rice paper flat, and then print it out word by word with a cloth bag; If the stele is too large or unfamiliar, it can be done partially.

Hello, is there any way to restore the old tombstone's handwriting falling off?

Ability to restore previous textual content.

With ink and rice paper, you can distinguish and see the inscription clearly; Prepare ink, rice paper, plates, Mao Hongzhao brushes, cloth bags and other materials and tools, first brush the mud and dust of the stele clean, pour the ink into the plate, use a tied cloth bag, dip ink evenly on the tablet surface, and then cover the rice paper to cover it flat, and then use the cloth bag to print it out word by word; The stele is too large or Li Dan is not familiar with it, so it can be completed partially.

Can this kind of thing be extended?

You can try to see if it's a little harder.

Often cemeteries are stocked with brushes and paints for use. Just draw it yourself. For your own cemetery, you need to bring your own red and black paint (some tablets have gold characters, you need to use gold powder paint, and the paint is best anti-rust paint) and brushes and rags.

Before tracing, worship the ancestors, show respect, and then clean the grooves of the words, wipe them dry, and carefully trace the words on the stele, if you accidentally trace them, wipe them off with a rag. <

Often cemeteries are stocked with brushes and paints for use. Just draw it yourself. In the cemetery with a wide wheel, you need to bring red and black paint (some tablets have gold characters, you need to use gold powder paint, and the paint is best anti-rust paint) and brushes and rags.

Before tracing, worship the ancestors, show respect, and then clean the grooves of the words, wipe them dry, and carefully trace the words on the stele, if you accidentally trace them, wipe them off with a rag.

Traditionally, red is used to represent the living, black to represent the dead, and surnames are all red, because a family's surname has always existed and been passed down. If you see a person's surname and first name on the tombstone, it means that he is the living. Usually, they are all elderly people who have reached the age of 80, and such a cemetery is called a longevity cave, which can add blessings and longevity.