Sweater double thread needle collection method, sweater double thread needle lifting method

The double-threaded needle of the sweater is the two-needle upper needle and the second needle-down, the double-threaded needle collection method, if the rod needle is the upper needle, the needle is closed by the needle method; If the needle is on the needle, use the needle method to close the needle.

1. The first needle is directly knitted on the edge, and the left rod needle is now the next needle, so use the upper needle method to weave, first withdraw the coil on the right, and hang the thread on the needle from the back and then pass through the coil.

2. The needle is closed by the method of the needle, and the needle is knitted.

3. Now there are two coils on the right rod needle, the first coil is set on the second coil, and the needle collection method of the lower needle is completed on the left rod needle.

4. Now the upper needle on the left rod needle is the upper needle, you should use the method of the lower needle to collect the needle, first withdraw the coil on the right rod, wrap the wire around the bottom of the rod needle from behind, and then put the coil on the rod needle.

5. Knit a needle and put the first coil on the right rod needle in the second coil.

6. Note that there is still a needle on the left rod needle.

7. Swap the position of the upper needle and the lower needle on the left rod needle, then the first needle on the left rod needle becomes the lower needle, and press the needle to continue to collect the needle.

The fabric with the needle folded is not only smooth but also elastic.

For double-thread take-up, the coil is threaded first, and then the wire is looped around the rod needle from behind.

When the two needles are closed, after the first needle is closed, the second upper needle and the lower needle are reversed and then the needle is closed.

The method of starting the sweater double thread is as follows:

Tools and raw materials: ring needles, rod needles.

<>4. Then turn over the surface and weave the needle or the remaining needle, and then turn over and weave a row of needles, a total of 3 rows. (The first row is knitted with needles, the second row is knitted with needles on the reverse side, and the third row is knitted with needles on the front)

<>6. Next, pick two coils on the rod needle, and then pick down two coils on the ring needle; Just cross it and repeat it. Pick all the coils on the rod pins. As shown in Fig

<> precautions: 1. After winding the wool on the rod needle and the ring needle, knit the needle on the front and knit 3 rows on the needle on the reverse.

2. When picking the needle, pick two needles above and two needles below.

Double thread is a commonly used mechanical connection method, which has the advantages of strong bearing capacity and fastening connection, and is widely used in machinery manufacturing, construction engineering and other fields. When making a double-threaded connection, the needle retraction is a very important step, and the following describes the method of retracting the double thread.

Selection of the needle receiving material.

Double-threaded take-up is usually made of spring steel wire or stainless steel wire. Spring steel wire has the advantages of high strength, good toughness, wear resistance, etc., but its elasticity is limited and easy to deform, so you need to pay attention not to overstretch it when using. Stainless steel wire has the characteristics of corrosion resistance and high temperature resistance, but its hardness is low, and it needs to be selected according to the need.

The method of needle receiving.

1) Single-sided needle closing method: wrap the spring steel wire or stainless steel wire around one side of the twisted thread, then push it into the twisted thread of this cover, pull it out from the other side, and finally cut off the two ends to make it in the same direction as the thread, so as to ensure that the connection of the thread is not affected after the needle is closed.

2) Double-sided needle closing method: wrap the spring steel wire or stainless steel wire around both sides of the twisted thread, Youxun pushes it into the thread, then pulls it out from both sides, and finally cuts off the two ends to make it in the same direction as the thread, so as to ensure that the connection of the thread is not affected after the needle is closed.

Whether it is a unilateral or bilateral needle collection method, the following points need to be noted:

1) The length of the take-up needle should be slightly larger than the length of the thread to ensure the tightness of the threaded connection.

2) The diameter of the needle should be slightly smaller than the inner diameter of the twisted thread to ensure that the connection of the thread will not be affected after the needle is closed.

3) When retracting the needle, care should be taken not to overstretch it to avoid deformation of the spring steel wire or stainless steel wire, which will affect the connection of the thread.

In short, the double thread needle collection method needs to pay attention to the selection of materials and the method of needle collection, and the length and diameter of the needle collection also need to be selected according to the actual situation to ensure the tightness and stability of the threaded connection.

The double-thread hand stitch is as follows:

1. Sew with a needle, close the edge and put it on the right, insert it from behind the first needle, and pull it forward from the second needle.

2. Fold back one pin, insert the pin from the front, skip the second pin, and then pull the needle forward from the third pin; Insert the pin from the front of the two pins and skip it.

3 or 4 needles, pull forward from 5 needles.

3. Fold back the three needles, insert the needle from behind, and then pull it out from the front of the four needles to the back.

4. The needle is inserted from the front five needles, and then pulled forward by the back six needles; Insert the pin from behind the four pins and skip it.

Five, five stitches, and then by.

The front of the seven and six needles is pulled backwards.

5. The same should be used in the order of face needle and face needle, inner needle and inner needle, one needle is inserted twice and the edge is closed. Effect mixing.