How to connect the three wires on the Wuling light generator?

First of all, there are three wires on the generator;

Secondly, there are six screws in the rear of the generator, which is a straight line;

Then, there are two more threads for the rest, one of the two roots behind the generator (after starting the car, the engine idle speed will change a little) is the generator control (connected to it, the generator works), and the other is the indicator light of the instrument, which is connected to it (turn on the ignition, the indicator light is on, the engine is turned off, and the generator is normal).

Generator Introduction:

A generator is a mechanical device that converts other forms of energy into electricity, and it is powered by a turbine.

Steam turbines, diesel engines, or other power mechanical transmissions, water, air, fuel combustion, or nuclear fission energy are converted into mechanical energy.

to the generator, convert to generate electricity by the generator. Generators are widely used in industrial and agricultural production, national defense, science and technology and daily life. Generators come in many forms, but their working principle is based on electromagnetic induction and electromagnetic forces.

The law of the law. Therefore, the general principle of its construction is to generate electromagnetic power with magnetic circuits and circuits with appropriate conductive and conductive materials to generate electromagnetic power to achieve the purpose of energy conversion.

The generator is mainly composed of stator, rotor, end cover, brush, base and bearing.

The stator consists of a frame, a stator core, a wire-wrapped winding, and other structural parts that hold these parts in place.

The rotor consists of a rotor core, a rotor pole pole (with a magnetic choke, a magnetic pole winding), a slip ring, and a copper ring. collector ring), fan and shaft and other components.

The stator and rotor of the generator are connected and assembled through the bearing, the base and the end cover, so that the rotor can rotate in the stator, and a certain excitation current is introduced through the slip ring to make the rotor become a rotating magnetic field, and the stator coil is used to cut the magnetic field lines.

The movement, which generates an induced electric potential, passes through the terminals.

When it is drawn out and connected to the circuit, an electric current is generated. Because there is a break at the connection between the brush and the rotor, the rotor rotates in a certain direction and generates alternating current.

Therefore, in circuits such as home circuits, it is alternating current, referred to as alternating current.

The frequency of the output current of the Chinese grid is 50 Hz.

If you really don't understand, then tell you the easy way, there are 6 screws on the back of the generator, which is to fix the thicker wire (through the battery).

The remaining 2 are connected to one of the two behind the generator with 12 volts (the engine idle speed will change slightly after the starting car) is the generator control electricity (connect it to make the generator work).

The other is the indicator light of the instrument, connect it (turn on the ignition switch, the indicator light of the instrument is on, it goes off after starting the engine, and the generator is normal).

Summary. The installation method of Wuling Hongguang ignition coil is as follows:

1. Open the ignition coil cover on the top of the engine;

2. Use an inner pentagonal wrench to remove the ignition coil fixing screw;

3. Remove the ignition coil power plug;

4. Use a screwdriver to gently warp it up and take out the ignition coil;

5. Put in the new ignition coil and tighten the screws;

6. After connecting the power plug, see the top cover cover.

How to connect the 4 high-voltage lines of Wuling Light.

Hello, very good to do the cha is happy to answer for you. Generally, there is an Xianshan mark on the igniter, from the front part, it is 1234 cylinders, and the control igniter (a row) is generally 1423 order.

Wiring diagram. I can't send ** here, oh dear.

How to look. You follow the text description.

How to insert the ignition coil here.

The installation method of Wuling Hongguang ignition coil is as follows: 1. Open the ignition coil cover on the top of the engine and hold the grip; 2. Use an inner pentagonal wrench to remove the ignition coil fixing screw; 3. Remove the ignition coil power plug; 4. Use a screwdriver to gently warp it up and take out the ignition coil of the leather touch; 5. Put in the ignition coil of Kiqingxin and tighten the screws; 6. After connecting the power plug, see the top cover cover.

Summary. Hello, the top and bottom symmetry is a group, the upper right corner is connected to the positive pole of the power supply, the lower right corner is connected to the negative pole of the power supply, the yellow and green switches, the two wires are connected to one good, the black ground under the symmetry, the two groups on the left are connected to the left and right channel horns, and the black is the negative pole of the horn.

Hello brother Xishou, up and down symmetrical for a group, the upper right corner of the white and red connection of the power supply positive, the lower right corner of the power supply negative, yellow and green switch, two wires with a good, symmetrical black grounding, left and right side of the two groups of the left and right sound Lu Huai Road horn, black for the horn negative.

I hope it can help you, I hope you can give a thumbs up, thank you for your support and trust, thank you.

Summary. The four wires of Wuling Light Progress Motor are U phase, V phase, W phase and ground wire. 1.

The U-phase wire is usually a blue or black wire that is located in one of the phases of the three-phase power supply of a progressive motor and is used to connect the U-phase in the AC power supply or drive. 2.The V-phase wire is usually a yellow or white wire that sits in one of the phases of the Progressive Motor's three-phase power supply and is used to connect the V-phase in the AC power supply or drive.

3.The W-phase wire is usually a red or orange wire that sits in one of the phases of the three-phase power supply of a progressive motor and is used to connect the W phase in the AC power supply or drive. 4.

The ground wire is usually a green or greenish yellow wire that is used to connect the housing of the progressive motor to the ground wire of the electrical system to ensure electrical safety. The wiring style and color of these wires may vary from manufacturer to manufacturer and from model to model of progressive motor, so you need to carefully check the wire markings and follow the wiring diagram provided by the manufacturer when wiring. At the same time, it is necessary to pay attention to safety when installing and using progressive motors, and it is recommended that the installation and maintenance should be carried out by professionals.

I'm still a little confused, can you be more detailed?

The four wires of Wuling Shisun Zhiguang Progress Motor are U phase, V phase, W phase and ground wire. 1.The U-phase wire is usually a blue or black wire that is located in one of the phases of the three-phase power supply of a progressive motor and is used to connect the U-phase in the AC power supply or drive.

2.The V-phase wire is usually a yellow or white wire that sits in one of the phases of the Progressive Motor's three-phase power supply and is used to connect the V-phase in the AC power supply or drive. 3.

The W-phase wire is usually a red or orange wire located in one of the phases of the three-phase power supply of a progressive motor and is used to connect the AC power supply or the W phase in the limb drive. 4.The grounding wire is usually a green or greenish-yellow wire that is used to connect the housing of the old wheel chain progressive motor and the ground wire of the electrical system to ensure electrical safety.

The wiring style and color of these wires may vary from manufacturer to manufacturer and from model to model of progressive motor, so you need to carefully check the wire markings and follow the wiring diagram provided by the manufacturer when wiring. At the same time, it is necessary to pay attention to safety when installing and using progressive motors, and it is recommended that the installation and maintenance should be carried out by professionals.

The top and bottom symmetry is a group, the upper right corner is connected to the positive pole of the power supply, the lower right corner is connected to the negative pole of the power supply, the yellow and green are connected to the switch, the two wires are connected to one piece, the black under the symmetry is grounded, and the two groups on the left are connected to the left and right channel horns, and the black is the negative pole of the horn.

Extended reading: The radio is the receiving equipment of the sound broadcasting system, which is an audio-visual electrical appliance. It restores the high-frequency signal received by the antenna into an audio signal, which is added to the speaker to reproduce the sound.

A radio is a small radio receiver. It is mainly used to receive radio broadcasts and listen to radio transmitters, usually entertainment and information programs sent by radio stations. It has radio receivers that are different from those for military use, the latter is not broadcasting.

A radio is a device made of mechanical devices, electronic devices, magnets, etc., which converts radio signals with electrical energy and can listen to the audio signals emitted by radio stations. Also known as radio, radio, etc. The advent of DSP technology radio marks the gradual retirement of traditional analog radio.

The digital age of radio has arrived.