How to slow down and turn a novice and how to turn a car for novices

Slowly apply the brakes and slow down at the same time, continue to control the speed with the brakes, and press the clutch when the speed drops below 10 km/h.

And still use the brakes to control the speed. Turn the steering wheel as the front of the car slowly enters the corner.

After controlling the direction with your left hand while turning, hang your right hand in 2nd gear. After cornering, the clutch is semi-linked, and the throttle is reduced. <>

The front of the car is parallel to the road and then returns to the positive direction, loosens the clutch, and refuels. Finally, step on the clutch, get into gear, and keep going. The shift in the turning is generally due to the wide road, the condition is good and the line of sight is clear, before the turn, the speed has slowed down somewhat, when the vehicle travels to the corner angle 1 2 places, the position of the steering wheel has turned a certain angle is also just right, because the driving resistance increases at this time, the vehicle is weak, so use the right steering wheel to return to the right before a gap time to shift gears.

The novice slows down and turns as follows:

Novices driving right turns, should first step on the brakes, wait for the speed to slow down and step on the clutch to change the low gear, and then slowly release the clutch, the speed is below 30 kilometers per hour, after the turn of the clutch, slightly step on the accelerator to accelerate, and then step on the clutch to hang the gear, and then accelerator to accelerate. After shifting to second gear, you don't need to step on the clutch, as long as you don't refuel.

The way for a novice to turn right when driving is to:

1.It is necessary to use the engine to pull the car to slow down, loosen the throttle, turn on the lights and brake in advance to slow down to give the rear car a reaction distance, (before entering the corner, calculate the cornering speed and route, consider the rain and road slippery, other cars squeezing over and other factors).

2.If the speed of the car is slow enough to turn off, then change gears (there must be a advance amount, otherwise you will be in a hurry).

3.Keeping the engine running smoothly is the key, the selection of gears is based on the current factors, and the safety of gear driving is high, and "try to avoid" neutral driving.

The process is generally coherent, maybe the time is slow but not a pause when the gear is in gear (in the corner, it is necessary to reduce unnecessary movements, reduce a little one-handed steering wheel state, otherwise "shift gears, step on the clutch, brake, look in the rearview mirror, observe other dynamics" Several actions are crowded in a bunch, it is easy to mess up, and it depends on your on-site judgment to separate and stagger in advance or delay).

5.If you force downshift directly without stepping on the brakes, the engine and gearbox will suddenly enter a high-load state, and if the brake light is not on, the car will suddenly slow down, and the rear car will not have time to brake.

At present, the development of automobiles is getting better and better, and the automobile market is getting stronger and stronger. Because novices are not familiar with the road conditions and are not proficient in the mastery of the car, it is easy to have such doubts, especially when turning, it is easy to turn or go on the road. Today, the car combines its own experience to talk about the skills of novice drivers in turning.

Are you afraid of newbie friends and friends? Don't worry, because the car side Xiao is here, today the car side Xiao will briefly introduce the novice driving and turning skills for the little friends.

Adjust the speed: Beginners must drive slowly, which is one of the most important prerequisites. Especially when turning, slow down in advance. Only by slowing down can you pass safely, and if you make a mistake, you can correct it immediately. Conversely, if you turn too fast, you are in danger.

Make as little a turn as you can when turning right:

When you turn right, sometimes you will come across a car going straight, like an intersection. At this time, if you need to make a turn, you need to make a small turn, so that it will not affect the normal driving of the straight vehicle, otherwise it will hinder others.

Turn left, turn as far as you can, turn a little bigger:

Because some cars will come out on the road where you are about to turn, you should try to turn as much as possible in order to prevent other obstacles or collisions.

Look in the rearview mirror:

When turning, be sure to look in the rearview mirror to make sure that no one is turning behind the car or behind the side. This point is often overlooked by many novices and can easily lead to travel accidents.

Pay attention to the corners of the corners:

Novices often don't look at the corners when turning, but look left and right, which affects the neglect of the corners, and is easy to press on the cornerstone of the road or scratch. You need to keep an eye out for obstacles under the rearview mirror. If necessary, you should open the door to take a look and then turn around.

Adjust the steering wheel to accompany the consumer:

When cornering, the adjustment of the steering wheel is very important. If you want to make a small turn, you need to kill the steering wheel as much as possible, and then slowly return to the right direction after turning; If you want to make a big turn, you need to take the direction slowly.

After reading the introduction of the car series, is it necessary for friends to understand the problem of novice driving turning skills? So, do your friends like the content knowledge that Bian Xiao Auto introduced to your friends today? Che Bian Xiao thinks that these are still very troublesome for beginners, so friends must read them carefully.

Finally, I hope that the introduction of Bian Xiao Automobile can solve the problem for friends.

Millions of car purchase subsidies.

When turning, the speed of the vehicle should not be too fast, before entering the curve, slow down in advance, slow cornering, try to avoid the use of emergency braking and meeting in the curve. The steering angle should depend on the actual situation, otherwise it is easy to lose control and lead to accidents, and it is also not conducive to the driver to observe the early situation of the car coming from the corner. Extended Resources:

1. Turning at fork roads: When turning left, the driver should send out a turn signal in advance, and when turning, he should rely on the road as much as possible to provide convenience for the rear car and the right-turning car. When turning right, you should also give a turn signal first, turn slowly, and pay attention to the influence of the inner wheel difference when turning, so as to prevent the right rear wheel from driving out of the road and rubbing pedestrians and obstacles.

2. Turning on the street or at the entrance and exit gates: Drivers should pay special attention to the debris piled up on the side of the road to slow down slowly, sound the horn and use turn signals or gestures to indicate the direction of travel. Do "one slow, two looks, three passes".

Pay close attention to the inside of the car's turn, and beware of pedestrians, bicycles, and motorcycles competing for the road and not knowing the direction of the car. 3. Turning on narrow roads: Drivers should sound their horns to slow down before starting to turn according to road conditions.

When the car is driving to a curve, the line of sight is inconvenient, and the car should be driven to the right side of the road to avoid obstructing the normal driving of other vehicles.

Beginner driving turnaround steps:

1. As a basic driving skill, car turning is often confusing for novices who have just started on the road. After driving into a curve, centrifugal force will be generated to push the car to the direction of the outer ring due to the change of travel direction;

2. First of all, on the highway or the road with a relatively gentle slope and a wide road surface, you should take a shortcut and turn. That is, when entering a corner, try to drive the car on the inside, and try to drive the car on the outside when exiting the corner. In this way, the arc of the car can be changed, the curvature of the car can be delayed, the centrifugal force can be effectively reduced, and the corner can be easily turned without slowing down without the width of the beam stool.

This method is more common in field car races, where a series of high-speed cars are all shortcuts;

3. Secondly, for uphill corners, the throttle should be released before entering the corner, so that the vehicle can enter the curve with a faster chain speed leaning on the outside of the curve, and then lower the gear by one or two gears, then select the route and correct the direction, and tap the throttle at the same time; After passing the top of the arc of the curve, then cut back to the outside of the curve, after confirming the safety of the road conditions, increase the throttle, and finally quickly drive out of the curve by relying on the outside of the curve;

4. When passing through the downhill curve, you should release the accelerator and step on the brake before entering the curve, so that the vehicle can slow down significantly, and lower the gear to one or two gears, and then enter the curve at a slower speed by leaning on the outside of the curve, and then release the brake to select the route and correct the direction; After passing the top of the curve, switch back to the outside of the corner, tap the throttle and finally quickly exit the corner against the outside of the corner. In this process, you should also choose a turning route with the outside first, then the inside, and then the outside.

Millions of car purchase subsidies.

The correct operation method should be to slow down and reduce the gear first, and then gradually increase the gear after passing the intersection or detour safely.

1. Shift gears before turning.

It is generally used on complex roads with many people and cars, or when the road is wide and straight, but due to the situation before turning, and the road conditions are unclear during the turn. Due to the gradual decrease in vehicle speed, the increase of driving resistance, and the lack of force of the vehicle, in order to increase the torque, it is necessary to change to a lower gear. Because this method is quite common and simple, you can practice turning before you train.

This is done by lifting the accelerator pedal about 30 m before the turn, using the drag effect of the engine's idle speed or gradually decelerating with the brakes. At a distance of about 15m from the intersection, that is, change to a low-speed gear according to the operation method of downshifting. In this way, when the vehicle reaches the intersection, it accelerates through the curve under the premise of driving safely.

2. Shift gears in turning.

The shift in the turning is generally due to the wide road, the condition is good and the line of sight is clear, before the turn, the speed has slowed down somewhat, when the vehicle travels to the corner angle 1 2 places, the position of the steering wheel has turned a certain angle is also just right, because the driving resistance increases at this time, the vehicle is weak, so use the right steering wheel to return to the right before a gap time to shift gears.

The way to do this is to hold your right hand in the upper left corner of the steering wheel and quickly push the gear lever into the next gear with your right hand, or to skip the shift according to the power at the time.

Because the shift in the middle of the turn requires the direction to be shifted while steering, and the direction is not deviated, so the difficulty is higher, so it can be practiced on the basis of the other two turning operations are more proficient.

3. Shift gears after turning.

Shifting after turning is generally also used when the road is wide and the line of sight is good, when the vehicle is passing through the turn, after braking lightly due to the situation, although the vehicle is weak, it does not shift gears, and only shifts into low gear after passing the corner, and quickly accelerates.

If you have shifted into a low gear before turning, you should speed up in time after the turn, shift into a higher gear and move on. After mastering the shift before, during and after the turn, it should be trained according to the actual situation of the road, and when there is a contradiction in the shift, it should be mainly dealt with (that is, brake, direction), and the other is secondary, and the gear should adapt to the speed and engine power needs, and the speed should adapt to the road conditions.

I suggest you take the block off early when cornering. This will allow you to glide through corners. There is no need to brake while pressing the clutch.

If you want to slow down, just apply the brakes a little. Don't do that if you're taking an exam. You can use this method when you are driving.

After cornering, you can directly hang the second gear. Give the oil and go.

Control the speed of the car when turning, and use the first gear if the second gear is blocked. You can use the half-clutch when you are ripe later. If there are too many people, stop the car and let pedestrians pass first. Safety first.

How to slow down and shift gears when turning in manual transmission, and how to shift gears correctly in manual transmission cars.

Regular, remember to slow before bending and fast after bending, and downshift in the middle of the bend.

When you brake to 20 yards before a specific corner, you can clutch your foot to the end. Brake below 20 yards, "you are the best to learn to drive, brake to 10 yards", and then lift the brake, "do not lift the brake, the car will brake", do not lift the clutch. Then observe the turning angle to determine how much direction to hit, quickly reduce the second gear after the direction is played, brake after reducing the gear, lift the right foot and put the accelerator, the clutch is slowly lifted, and the throttle is lightly increased while returning to the direction.

If you suddenly want to turn, it depends on your braking skills, neither brake, nor brake, but also can't brake at speed, take your time to find the braking feeling. There is also a level of gear addition, which cannot be overstepped. Downshifts can be overshifted, depending on how many yards you brake at the time and then decide how many gears to downshift.

Manual transmission cars can press the brake pedal to slow down just like automatic cars before turning. In the driving of the car, except for low-speed braking and parking, you need to press the clutch pedal, and try not to press the clutch pedal in other situations.

The speed of the car is relatively slow, or when you make a big turn, you just need to apply the brakes and slow down appropriately. After that, you can speed up with refueling without stepping on the clutch to change gears. Therefore, when turning, you should control the speed of the vehicle, brake and slow down first, and slow down according to the size of the bend.

When the car turns, the speed should be slow, and the steering wheel should not be too fast, so as not to cause the car to slide due to excessive centrifugal force.

Slow down by pressing the brakes before entering a corner, release the brakes when you start a turn, and then downshift according to your speed. Deceleration in corners, semi-acceleration in corners.