What should I do if there is no gap between the cabinet and the wall?

What should I do if there is no gap between the cabinet and the wall? What to do with the gap between the wardrobe and the wall; Apply putty powder first to fill in the gap between the cabinet and the wall. Then, use plaster block powder on the remaining gaps and do the work of making up.

After the treatment is done, brush the gaps with super glue and attach a glass cloth. Subsequently, a layer of putty powder is scraped on the surface to keep it level with the wall. Eventually, it is enough to polish it with an abrasive cloth and brush it with architectural paint.

What is the reason for the gap caused by the wooden cabinet; Before the wardrobe is customized, it is necessary to carry out the inspection of specifications to minimize the occurrence of deviations and ensure the overall actual effect. If the specifications are checked before the floor wall is assembled, there is a high risk that there will be gaps in the middle and later stages. Therefore, before measuring the size, it is necessary to communicate clearly with the seller, and arrange the time to measure the size, how to reduce the common deviation as much as possible, and the assembly will be more successful.

If there is a problem with the design of the cabinet and the layout is not carried out according to the specific situation in the room, it is very likely that the bearing capacity will be uneven or displaced, and then there will be gaps, which will endanger the application. Therefore, the owners of the community must communicate with the technical professional interior designer to minimize the problems in the key points, how to ensure the overall design of the room, and prevent the construction of the project in the middle and late stages.

There is also a situation where there is no gap in the wardrobe after it is installed. Only in the middle and late application time for a long time, the gap or skewed situation, which will cause the internal area of the wardrobe to occur unbalanced situation, at this time the internal structure can not place too many items, otherwise it is very likely to occur the situation of wardrobe deformation, what to do about the gap between the wooden cabinet and the wall, and what is the reason for the gap caused by the wooden cabinet, it will be introduced here, you have mastered it. If there is a gap between the wardrobe and the wall, it is necessary to repair it immediately, how to ensure the normal application in the middle and later stages.

In the process of doing whole-house customization, the size should be measured and the wardrobe should be customized according to the size of the wall, so that there will be no gap between the two.

To level the wall, the main processes are: First, smooth and straight. The second is to punch the tendons. The third is to find the right side. If the walls are leveled, there will be no gaps when making cabinets.

When we decorate, we want there to be no gap between the cabinet and the wall, we can do beautiful seams, fill it with cement or white mud, and then beautify it.

The first one is the problem of wall decoration workers, the uneven height of the wall is significantly the ground leveling is not in place, the bricklayer master must wipe the mortar leveling, and then the painter will make up. The latter is the problem of furniture customization manufacturers, and the flatness of the wall was not measured before making a wardrobe. Nowadays, when installing wardrobes, there are all levels, and you can understand that the wall is straight and curved, and it goes without saying that the measurement work is not done well.

One is: first fill the gap with foam glue, which has the effect of preventing cracking, then scrape it flat with putty powder, and then paste a circle of anti-cracking gauze, and finally use putty to polish and polish the paint.

If you want to do it yourself, at the same time, you want to be easier to use and be able to fill the gap with structural adhesive. The structural adhesive is good enough, and the gap is easily repaired. However, after a period of application, the structural adhesive will turn yellow and black, and the durability and aesthetics are insufficient.

Another way is to use wooden corner strips to block the areas with gaps, and then change the nailing gun to nail the wooden corner strips, so that the gaps can be blocked, and it is not easy to affect the appearance. The back wall is not vertical. This kind of thing is more common in everyone's wardrobe after the assembly, there are gaps of different sizes between the back panel of the wardrobe and the wall.

The most common situation is that the upper gap is small, the lower gap is large, or the lower gap is small and the upper gap is large. This shows that the wall is not vertical, and the vertical wall is not solved when the interior decoration is done. There is a deviation in the flatness of the ground.

In other words, our wardrobe is assembled by floor-to-ceiling, and after floor-to-ceiling assembly, the wardrobe is skewed due to the uneven road surface, so that there is an uneven gap with the middle of the wall. The wardrobe is not installed in place. The wardrobe installation is not in place, which means that the wardrobe customized by the goods is required to be assembled against the wall, but in the case of specific assembly, it is not assembled by the wall.

In fact, the main reason for this kind of problem is that there is a problem in the case of the custom size of the wardrobe.

You can use a sewing agent to fill this gap, which will look more beautiful and is not prone to problems.

You can fill it with plaster blocks, because that's what I have in my house. Then I'll mix it with a quick mix of plaster and dry powder to fill it in.

It can be filled with some foam glue, so that the wardrobe can be better fixed on the wall, not easy to collapse, and can also better fill the gaps.

It may be caused by the measurement, it may be caused by the production, for example, the cabinet that should have been 1.8 meters is actually only 1.7 meters, then there will definitely be a gap of 1cm after installation, and this gap is uniform up and down, equal width. The former is the problem of the wall decoration master, the uneven wall is obviously not leveled in place, the mason master needs to wipe the mortar leveling, and then the painter will continue to make up. The latter is the problem of custom furniture manufacturers, and the flatness of the wall is not measured before making cabinets.

It is a custom wardrobe, the wardrobe is measured according to the floor tiles, to the position of the top, confirm the height of the wardrobe, width, according to the indoor area, a few centimeters more, a few centimeters less, the custom wardrobe is not processed on site, and a slight error is normal.

If you want to do it yourself and want to make it simpler, you can fill the gaps with glass glue. The glass adhesive is good enough, and it is easy to repair the gaps. However, the glass glue will turn yellow and black after a period of use, and the durability and aesthetics are not enough.

And will be a certain measurement of whether the wall is vertical, if it is found that the wall is not perpendicular up and down, will communicate with the owner or the person in charge of the decoration how to deal with the wall, and then the order will be placed.

The suit door is not installed, and the gap in the upper part of the wall on the right side is very easy to handle, so there is no solution. In the picture above, the verticality of the façade was initially popped up with a baseline line, and the ceiling was integrated with three lines at one end of the wardrobe, where the walls should be leveled with plaster as a whole. In the early stage, after the master's wall treatment is complete, the re-ruler treatment will be carried out.

Make sure every size fits tightly. When reading the ruler, try to reduce 3-5mm at the full size position to ensure that the combined size of each board after splicing is larger than the actual size of the drawing.

The expansion and contraction ratio of thermal expansion and cold contraction is not the same, and if you use putty treatment or glue, it will definitely crack in the future. If it is in the decoration process, you can first use foaming agent to hook the joints, then use putty to sew the seams, and finally the brusher. If it is a renovated house, the custom wardrobe can only be seamed with glass glue.

Personally, I think that if there is a gap between the customized wardrobe and the wall, it needs to be treated at this time, and you can ask a professional person to deal with it, which will be more beautiful.

Answer: Hello: If there is a gap between the customized wardrobe and the wall, the overall appearance will affect the aesthetic effect. How to deal with the gap between the custom wardrobe and the wall? PChouse will take you to find out.

1. Scrape the width of the gap between the custom wardrobe and the wall with a putty knife, and scrape it into a figure-eight shape, with a wide outer width and narrow inside. 2. Use dry powder gypsum blocks to plug the gaps, the filling depth is not less than 30-40mm, do not fill with the wall, brush 108 glue at the lower gaps than the wall and paste the glass cloth or kraft paper strips. 4. Scrape 821 putty 2-3 times to be level with the original wall, and polish it with sandpaper after drying.

5. Configure wall paint, brush the sample first after the paint is configured, and contrast with the wall color after drying, the color is close, and the color difference is not large, so it can be painted.

We should decorate it with some small ornaments, so that it can also cover up this flaw, for example, putting some fake grass and flowers in ** is also very good-looking you.

When you find a gap, the best way is to make plaster lines, which will not only decorate, but also make the wardrobe and wall look more harmonious.

If there is a gap between the wardrobe and the wall, then it may be that the wardrobe or the wall is not flat enough, and the wall needs to be filled.

The gap should be plugged with putty or foam, and there is no need to make a big fuss. This will not compromise on aesthetics.

You can fill the gaps with some filler and then apply a similar paint to the outside so that they don't look out.

In such a situation, you can choose some good materials to fill these gaps so that it will not look so strange.

1. Styrofoam filling, fill the gap between the wardrobe and the wall, and after filling, scrape putty to supplement, and then fill the gap.

2. You can stuff a long strip on the gap, and then apply putty, and also paint it, or you can put your favorite sticker on it.

You can use styrofoam in the middle of the gap between the wall and furniture to plug the gap, after the gap is filled, you can scrape the putty of the same color as the wall on the surface of the gap, and finally apply the relevant paint on it for repair. Second, in addition to using styrofoam to fill the gaps, you can also use gypsum blocks to fill, when adding it must pay attention to a distance from the wall, at least keep it at 1 mm with the wall, so that the effect of filling out is the best, so we must master this measure.

In this case, it is often that the custom wardrobe business has not done a good job, you can find them for after-sales service, and you must put forward your demands in the production process. Hopefully the problem will be resolved soon.

Normally, there should be no gaps after the installation of the custom wardrobe and before the wall, it looks like a complete whole, if there are gaps, first determine whose responsibility is responsible, and then let the responsible party solve it according to the attitude of who is responsible for whom.

Why are there gaps in custom wardrobes and walls?

1. The wall is not vertical

The side of the wardrobe after installation must be perpendicular to the ground, if the wall of the wall is not vertical, then there will be a gap between the wardrobe and the wall, this gap is uneven, the width of the gap above is not the same as the width of the gap below.

2. Size error

Size error refers to the size of the custom wardrobe has been wrong, it may be caused by measurement, it may be caused by production, for example, the cabinet that should have been 1.8 meters is actually only 1.7 meters Then there will definitely be a 1cm gap after installation, this gap is uniform up and down, equal width.

Who's to blame for having gaps in custom wardrobes and walls?

Generally speaking, when the size of the custom wardrobe is measured, the wall has been almost constructed, and the wall will be measured vertically, if it is found that the wall is not perpendicular up and down, it will communicate with the owner or the person in charge of the decoration, how to deal with the wall, and then order production.

Therefore, the gap caused by the wall is not vertical, and it is necessary to determine whose problem it is, and then find the corresponding person to be responsible; If it is caused by a size error, if the size of the space is not changed after the measurement, then there is no doubt that it is the merchant's problem, and the merchant is responsible.

Conclusion: If the gap is more than 5 cm large, first fill it with a plate of the same color, and then close the seam with glass glue; The gap is less than 5 and more than 1 cm, first fill it with styrofoam, and then fill it with gypsum powder + putty powder, and then directly hit the glass glue at a centimeter.

The above is the way to solve the gap between the custom wardrobe and the wall, you can choose the right solution according to the actual situation. Among the above 5 methods, the use of styrofoam is a better method.

After brushing glue on the gaps, paste the glass cloth, scrape the 821 putty and smooth the original wall, and polish it with sandpaper after drying. Equipped with wall paint, after drying, there is little difference between the contrast between the wall color and the color of the wall, so that it can be painted. It can also be filled with foam expansion agent, and it can be brushed with latex paint on the wall putty.

In this way, the cabinet and the wall are combined, and it is not easy to crack in the future.

There is a gap between the custom wardrobe and the wall, which should be treated like this, you can stuff a long strip into the gap, and finally scrape the putty, and finally paste the wallpaper, so that you can't see it.

This is very simple, many custom wardrobe installers will leave a little gap in order to retain the operating space, and these gaps will be filled with foam caulk in the end. That's what my family is trying to solve.

Nowadays, many people will choose a custom wardrobe when decorating their house, not only because it has a larger storage capacity than the traditional finished wardrobe, but also because its style can better meet people's needs for differentiation and personalization.

In order to catch up with the construction progress, many people ask the manufacturer to go to the site to measure before the completion of the complete decoration, which will lead to a large dimensional error in the measurement, resulting in a large gap after installation.

The thickness of the normal wall scraping putty is about 2cm, if the wall error is too large, it needs to be leveled with cement mortar or gypsum board in the early stage, but many decoration companies will intentionally or unintentionally ignore it when signing the contract with the homeowner in the early stage, and many homeowners are not willing to add items in the later stage, which will lead to the construction party not doing this process during construction, resulting in hidden dangers in the later stage.

The gap between many custom wardrobes and the wall is caused by the lack of consideration of the position of switches and sockets in the early stage, resulting in the inability to close the wall in the later installation cabinet. If the gap is not very large, just for the pursuit of beauty, it is recommended to do glue treatment, scraping putty is still not recommended, because the texture of putty is relatively hard after drying, the cabinet and wall are relatively deformed, and the putty will continue to appear gaps or even fall off after all, so the elasticity and adhesion of the sealant are better choices.

If the gap is too large, this problem is generally caused by inaccurate measurement, we can ask the manufacturer to use the cabinet plate of the same material to do unilateral edge banding treatment, and then cut and fill according to the size of the gap, and finally do glue treatment.

It can be filled with foam expansion agent, and it is enough to brush latex paint with wall putty. In this way, the cabinet and the wall are combined, and it is not easy to crack in the future. Don't use glass glue, you can use Black & Decker edge glue indoor type.

Custom furniture must be measured before the manufacture of the owner's room to avoid some of the dimensions of the furniture, many owners in the decoration or has not been decorated when the door-to-door measurement, at the moment the height of the ground, wall disposal and so on is not finished, it is easy to cause the furniture to be transported to the home after finding that the equipment can not be transported, such as the cabinet is high after the stairs can not be transported upstairs.