Detailed steps for the installation of the baby wooden bed, steps for the installation of the crib

The installation method of the crib is relatively simple, many people will choose to assemble the crib by themselves, the installation steps of the crib can be divided into the following 3 steps, the following Luban to the home will simply introduce to you.

1. Product inspection.

Before installing the crib, we need to take out the installation materials and accessories of the crib and check them according to the list of product accessories. It is best to classify the accessories of the crib, and it is best to store accessories such as screws in boxes to avoid loss and so on. You also need to check the quality of the crib, for example, we can check the crib for burrs, odors, surface inequality.

If there is a quality problem with the crib, you can contact the merchant to return it.

2. Install guardrails and bed heads.

We take out the fixed head of the bed and the guardrail, put the side of the guardrail in line with the screw hole next to the head of the bed, and then stuff the long screw into the screw hole, tighten the screws to connect and fix them together. Then follow the same method to connect and fix the extended head of the bed and the fixed guardrail. When installing the folding guardrail, we will clamp the upper two ends of the folding guardrail on the card slots of the two bed heads, and only use screws to fix the lower part of the guardrail and the two sides of the bed head together.

3. Install bed boards and other components.

We put the storage support on the crossbar under the guardrail on both sides, generally put two on the folding guardrail, put three on the fixed guardrail, and the spacing of the storage support should be even. Once the storage tray is installed, we place the storage plate on the storage pallet. We can see that there are three screw holes in the middle of the guardrail on both sides, which are used to install the bed board drag.

We tuck the screw rod into the screw hole in the middle of the guardrail and tighten the nut to secure it. To fix the screw in the middle of the guardrail, you only need to insert a screw. After the bed slats are installed, we put the bed slats in place.

When placing the bed board, the perforated side of the bed board should be aligned with the fixed guardrail, and then the guardrail and the bed board should be fixed together with screws. Finally, we used screws to install the pulley, the extended support rod, and the mosquito net rod.

Do you know what the steps are to install a crib? Ladies and nurses, let's take a look at the steps to install the crib:

1. First lengthen the lower end of the bracket. The metal parts are snapped into the chute of the extended side frame, and then the plastic parts at the upper end of the extended bracket are clamped into the corresponding square holes, and fixed with 1 M6*35 screw lock breast from the side. It should be noted that the willow nails on the extension bracket are curly inwards and the warnings are installed outward.

Then use 9 screws with the same screws to assemble the front lower frame, the back frame and the two sides of the frame.

2. After installing the above bracket, then put the storage board on the lower layer, put the bed board on the upper layer, pay attention to it, don't use the storage board as a bed board, and then close the extension frame, and then use screws to lock the rear side frame through the upper end hole of the side frame to fix the extended bed.

3. After all are installed, then flip the connecting sleeve on the side frame outward to the horizontal, then rotate the front frame upward, snap the plastic connectors at both ends into the connecting sleeve, and finally, continue to pull the connecting sleeve downward until it is perpendicular to the ground to complete the fixing of the movable guardrail.

4. In the last step, install the wheels, stuff the four wheels into the plastic sleeve at the lower end of the bed leg, press the bed body down to complete the installation of the entire caster, and then, use the screws to pass through the screw holes in the vertical gear in the rear basket and the lower frame of the front guardrail, lock into the screw holes corresponding to the bed board, and lock the fixed wooden board OK.

How to install the crib 1, the spring frame position, insert the round teasing cylindrical fastener (d) into the hole in the spring frame in the lower position (c) and fix it with 4 hexagon bolts (f). Use the included Allen wrench (L) to tighten. 2. Insert the stud on the side post into the corresponding hole in the headboard guide.

Slide up about 13cm to compare with the other side. Make sure the sides are parallel to the headboard footrests. Press and hold the two spring pins in the side edges.

And align the sides between the headboard and footrests, shaking the sides until the two spring pins have been inserted into the guide. Lift the blind side of the side nucleus so that the pin runs along the guide and is in the correct position. 3. Align the holes on the side edges with the matching holes on the headboard and footrests on both sides of the fixation.

Thread the Allen screw (F) through the holes on the side and into the matching holes on the headboard and footrest, tightening using the included Allen wrench (L). Tighten the screws to make sure they don't loosen, check their tightness regularly. 4.

On the lower side, insert the blanking screw (m) into the hole on the lower side (inner side). tighten the screws to prevent them from loosening; Periodically check that it is fastened to the falling edge of one-handed operation. The crib has two drop sides:

It is recommended to pin one of them. 5. Install the casters and insert the casters (g) into the bottom of the pedal legs (a) at the head of the bed, and do not hit the casters directly with a hammer! Place a piece of wood or something like that, change the emptiness, and hit the wood with a hammer.

Use (h) to connect the rollers.

1.First, carefully check the installation instructions of the wooden bed, and arrange the planks, screws, and tools that need to be combined neatly.

2.Assemble the bracket of the bed first. Break the hole and put the screw.

There are two tricks when screwing, the first is that the screws are perpendicular to the plank, so don't deviate. That's how you can exert your strength. Second, don't tighten it too tightly at the beginning, and then strengthen and tighten it after assembly.

3.Once the bed frame is installed, it's time to install the fence. There are some long screws and short screws, and I personally think that short screws are easier to put on. There are two screws on one side, a total of four need to be on, and it's OK when it's finished.

4.After the fences are installed. The rest is very easy. It's just to put the bed board on it. Pay attention to it when laying, smooth it upwards, and try not to make the gap between the bed boards too large, so that it is uncomfortable to sleep.