The computer headset suddenly has a rhythmic sizzling sound, 2 times per 1 second, which is not a pr

It may be that the hard disk is in a large number of reads.

Then the electromagnetic waves emitted by the data cable interfere with the power amplifier circuit of the computer, and the headphones always have a sizzle when the computer copies the file!

This is normal.

It is also possible that your headphones are too responsive, your headphones are too close to the source of interference, it may be that the electromagnetic waves emitted by the power supply of your case make the headphone cable produce **current, because your headphones are too sensitive, a small current will push your headphone diaphragm to make sound. Or there are other radiation sources in the place where your headphone cable passes, check to see if there are any printers, ADSL power supplies, case power supplies, speakers and other equipment. Workaround:

1: If there are other sources of interference, take them far away, if it is power interference, please ground the power supply to deal with it, the power supply will not be grounded will leak out the electromagnetic radiation in the chassis, which is not good for human health.

2: If you can't take those devices, go to the computer market and buy an audio cable, the quality is better, the kind with shielding. Connect the extension cable to the computer first, away from the computer and then to the headphones.

Personally, I think the first method is the most effective and the most fundamental. The second method is not recommended!

Attention, the sensitivity of your headphones is too high, this is the performance of ***, the headphones with higher sensitivity are not suitable for turning on the computer at a louder volume, protect your headphones, and listen to the headphones before listening.

There is also the possibility of current noise.

There is a problem with the headset or the receiver is broken!

It's the sound of headphone current, so let's change to headphones.

The reasons why the newly purchased headphones will have a sizzling sound and how to deal with it are as follows:

1. If you don't clean up in time, you have too much system garbage and slow response, so you should clean up the system garbage and anti-virus of the computer in time.

2. If the headset is damaged, you can compare the headset with other headsets or computers, and replace the headset if necessary.

3. The computer has static electricity, which is also the main reason. Touch the iron part of the computer case with your hands, if the current sound disappears, connect a piece of copper wire, one end to the screw behind the computer, and the other end to the ground, the effect is excellent.

4. Whether the microphone is in a strengthened state. Solution: Remove the microphone reinforcement. Because some sound cards don't support it.

5. See if there are any things with magnetic fields and sound waves around. Solution: Take away electrical appliances with magnetic fields (such as mobile phones, fans).

6. The problem of the earphone itself, which may be caused by the current sound caused by the surrounding electromagnetic radiation, or it may be the current sound of the poor performance of the earphone itself, and the better earphones can filter out the current sound even if there is current sound when the audio output; Workaround: Replace the headphones with a new one.

Summary. 1. If there is no sound in **, but there is a sizzling sound in the state of the connection, it may be caused by the low noise of the Bluetooth headset itself, which cannot be completely eliminated; The generation of this low noise is due to the interference in the process of Bluetooth wireless signal transmission, which is a common phenomenon of Bluetooth headsets, and the decoding chip of the mobile phone will also produce a slight noise background in the process of analyzing audio;

2. If it is the reason for mobile phone decoding, you can select the Bluetooth LDAC encoder in [Settings] - [Developer Options] on the mobile phone, which can reduce the noise floor as much as possible; There are some relatively cheap Bluetooth headsets due to the optimization of the chip and the poor anti-interference ability of the Bluetooth signal, which is more prone to noise floor, and the noise floor of generally higher products will be relatively slight; If the noise floor is too large and affects the effect of your listening**, you can try to use an adapter cable to use Bluetooth headphones;

The headphones have a sizzling sound all the time.

1. If there is no sound in **, but there is a sizzling sound in the state of the connection, it may be caused by the low noise of the Bluetooth headset itself, which cannot be completely eliminated; The generation of this low noise is due to the interference in the process of Bluetooth wireless signal transmission, which is a common phenomenon of Bluetooth headsets, and the decoding chip of the mobile phone will also produce a slight noise background in the process of analyzing audio; 2. If it is the reason for mobile phone decoding, you can select the Bluetooth LDAC encoder in [Settings] - [Developer Options] on the mobile phone, which can reduce the noise floor as much as possible; There are some relatively cheap Bluetooth headsets due to the optimization of the chip and the poor anti-interference ability of the Bluetooth signal, which is more prone to noise floor, and the noise floor of generally higher products will be relatively slight; If the noise floor is too large and affects the effect of your listening**, you can try to use an adapter cable to use Bluetooth headphones;

1.There is a possibility that the phone has a headphone port current problem, which is a hardware problem with the phone, and the headphones can be replaced to check, 2It may be that the headphone jack is not plugged in properly, you can rotate the headphone plug to detect.

3.There may be a problem with the headphone line, generally due to the old damage of the line due to the entanglement, which generally appears at the back end of the plug and can be detected by shaking the earphone cable and the plug link part. 4.

Then there is the problem of the headphones themselves, which may be the current sound caused by the surrounding electromagnetic radiation, or it may be the current sound of the poor performance of the headphones themselves, and the better headphones can filter out the current sound even if there is a current sound when the audio output.

1. Use a toothpick to pick out the dust hidden in the earphone jack and clean it up.

2. Dip a drop or two of alcohol into the earphone plug and insert it into the earphone jack, quickly plug and unplug it several times, this operation can be repeated once or twice.

If it doesn't work, borrow someone else's original earphone and try again, if it is normal, it means that your earphone is internally disconnected and needs to be replaced. If the problem still exists, it means that the contact of the earphone socket is poor, and it needs to be repaired and replaced with the earphone socket or the tail socket cable assembly needs to be replaced.

Hopefully my answer will help you.

It could be one of the following issues:

1.There is a problem with the headphones, in this case, you can replace the headphones.

2.If the contact is poor, just plug the earphones back in.

3.If the channel is set incorrectly, check if mono is turned on in the accessibility function.

4.If you have any problems with the software or hardware of your mobile phone, you can send it to Apple for after-sales repair.

If there is a problem with the headphone cable (the quality of the cable itself, or the internal wire is broken due to your hard pulling), or the plug connector is not plugged in well (there are too many plugs and unplugs, and some low-end plugs are not in good contact), change the headphones to try it, and if it doesn't work, it will be sent for after-sales maintenance, but it is generally better to change it, the after-sales service attitude is not good, and it is not guaranteed.

The reasons for this may be as follows

1.There is an open circuit in the cable of the earphone.

2.The plug is in poor contact with the metal parts inside the audio hole.

The headphones have sound while not doing anything.

Summary. Pro-<>

Hello, my answer is as follows, please be patient and look at the <>

Here are a few causes and solutions: High volume and computer setup issues: Make sure your computer's volume is adjusted appropriately, and check the audio settings of your operating system and applications.

You can go to your computer manufacturer's official website and audio device manufacturer's website to find the latest audio drivers and follow the instructions to install them. Hardware connection issues: Check that your computer headset is properly connected.

Try plugging the headphones back in and making sure they're fully plugged into your computer's audio jack. Loose and damaged headphone cable: Check for loose and damaged headphone cable.

Try testing with other headphones and there is no problem with the other headphones, that's because there is a problem with your headphone cable.

What should I do if the computer headset has a regular prompt tone all the time.

Hello dear <> my answer is as follows, please be patient and take a look at the <>

Here are a few causes and solutions: High volume and computer setup issues: Make sure your computer's volume is adjusted appropriately, and check the audio settings of your operating system and applications.

You can go to your computer manufacturer's official website and audio device manufacturer's website to find the latest audio drivers and follow the instructions to install them. Hardware connection issues: Check that your computer headset is properly connected.

Try plugging the headphones back in and making sure they're fully plugged into your computer's audio jack. Loose and damaged headphone cable: Check for loose and damaged headphone cable.

Try testing with other headphones and there is no problem with the other headphones, that's because there is a problem with your headphone cable.

Mine is a bluetooth headset.

It's been a regular chime.

I had no problem connecting my phone.

My computer is a ThinkpadX1

Dear, the following reasons and solutions: Low battery prompt tone: Your Bluetooth headset battery is too low, it will emit a regular prompt tone.

Try connecting the earbuds to a charging device to charge them to make sure they have enough power. Pairing and connection issues: Your Bluetooth headset won't pair and connect to your computer properly, and it will emit a regular tone to indicate a connection problem.

Make sure the Bluetooth connection between the headset and the computer is stable and established correctly. You can try to re-pair the headphones with the computer, and forget the headset device on the computer and reconnect it. Error operation and function beeps:

Some Bluetooth headphones can emit different tones to indicate different operations and functions. Please read the user manual of the headset carefully for the operation or function related to the specific tone to resolve the issue and adjust accordingly. Firmware Update:

Make sure your Bluetooth headset firmware is up to date. Sometimes, a firmware update can fix issues related to the tone. Please visit the headphone manufacturer's official website** to check if there is an available Gel Missing Parts update and follow the instructions.

Hello dear, reasons: 1. The computer was not cleaned up in time, too much system garbage was piled up, and the computer reflected slowly. 2. The headset is damaged.

3. The electrostatic electricity in the electric version of the brain is also the main reason. 4. The microphone is in a strengthened state. 5. There is a magnetic field source or sound wave source near the earphone.

6. Abnormal sound during voice calls. 7. If the microphone is not turned on to strengthen, the volume of the headphones will be very small, and there will be a lot of current noise when the microphone is turned on to strengthen. 8. The headphone jack is faulty.

Solution: 1. Clean up the system junk and anti-virus of the computer. 2. Compare the headset with other headphones or computers, and it is easy to judge whether it is a computer problem or a headset problem, and replace the headphones if necessary.

3. Touch the iron part of the computer case with your hands, if the current sound disappears, you can put a piece of copper wire, one end is connected to the screw behind the computer, and one end is grounded, you can eliminate the current sound, and the effect is excellent. 4. If the microphone is in the strengthened state, turn off the microphone for strengthening, because some sound cards do not support it. 5. Remove the electrical appliances with magnetic fields.

6. If the voice is abnormal only when you are connected to your friends, it will be normal in the chat hall. 7. If the microphone is not turned on to strengthen, the sound of the headset is very small, and there will be a lot of current noise when the reinforcement is turned on.