How to make the simplest pencil case, how to make your own pencil case

First of all, we need to prepare two pieces of fabric about 20 to 30 cm long and a 30 cm long zipper.

The zipper is used as shown below, using the middle 25 cm part.

On the inner part of the fabric, draw two cut outlines with a black pen.

Remove the excess along the black contour and leave a gap of about 1 cm for the edge suture.

Place the zipper between the front and back pieces of fabric, with the fabric lining facing outwards and the zipper aligned with the fabric. A small needle can be used to secure the position.

Stitch the zipper to the fabric on top according to the red thread.

Flip it back to the front and secure both ends of the zipper.

The suture of the lower part with the process"5"Similarly, it can be fixed with a small needle.

Like steps"6"Similarly, sew the zipper with the fabric (sewn it partially according to the red thread).

Next, separate the front and inner side materials from each other.

As shown in the figure below, the upper and lower edges of the upper and lower sides are partially sewn together. Fold the part of the edge cut line along the black line and sew the fabric (red line).

Repeat "Step 12" on the edge of the other side as shown below (red line).

As shown in the figure below. Unzip it off, as shown below.

Suture the bottom. Sew the fabric along the white line, leaving the seam on the right side of the yellow line.

As shown in the figure below. The front and rear fabrics and lining fabrics are shown below.

Pull out the fabric from the reserved part, straighten the fabric, and clip the corner part with tweezers.

The reserved mouth is stitched by hand.

Straighten the pencil case and sew the threads (yellow lines) on both sides.

Please refer to the figure below, reserve about two centimeters at both ends of the zipper, cut off the excess, and wrap and sew the two ends with excess small cloth blocks. (Don't let the zipper fall out of the slider after cutting).

Use a thin wire to pass through the gaps at the reserved ends.

Suture both ends through the closure () so that the wire does not fall off.

That's it! Do you understand the simple and good-looking handmade pencil case tutorial! Handmade fabric pencil cases that you are satisfied with, and it is a good choice to give to relatives and friends, simple and good-looking, hurry up and act!

Just go to the trash can and find a smelly sock (I'm here to be funny, don't really do that).

Make a simple pencil case, a large-capacity and waterproof stationery box, and you can make it with a piece of paper.

The tutorial of homemade pencil case is as follows:

Preparation materials: fabric, zipper, needle and thread, ruler.

Production steps: 1. Cut, cut a rectangle 22 cm long and 10 cm wide, and a 20 cm zipper.

2. Sew both sides of the zipper on both sides of the length. Pay attention to alignment.

3. Sew the bag in reverse and hide the cavity on the other two sides.

4. Fold the bag backwards. So the pencil case is ready, put a few pens in it and try it.

5. The position of the zipper can be placed on the side, which is more convenient to use.

6. You can add a small handle to make it easy to hang up. Just clip a strip of cloth when sewing the side seam.

The pencil case can be used to hold pens or other small stationery, which is more convenient to carry and more comfortable than the stationery box, and is more space-saving than it. The pen round posture bag is very popular with students. According to the material, the pencil case has leather, synthetic leather, cotton, oxford cloth, plastic pencil case and three-dimensional pencil case.

There are rectangular, cylindrical and variant-shaped.

The tutorial of homemade pencil case is as follows:Preparation materials: fabric, zipper, needle and thread, ruler.

Production steps: 1. Cutting, cutting a rectangular macro mu shape with a length of 22 cm and a width of 10 cm, and a zipper of 20 cm.

2. Sew both sides of the zipper on both sides of the length. Pay attention to alignment.

3. Sew the bag upside down, the other two sides.

4. Fold the bag backwards. So the pencil case is ready, put a few pens in it and try it.

5. The position of the zipper can be placed on the side, which is more convenient to use.

6. You can add a small handle to make it easy to hang up. Just clip a strip of cloth when sewing the side seam.

The tutorial of homemade pencil case is as follows:

Preparation materials: fabric, zipper, needle and thread, ruler.

Steps: Rubber Signs:

1. Cut, cut a rectangle 22 cm long and 10 cm wide, and a 20 cm zipper.

2. Sew both sides of the zipper on both sides of the length. Pay attention to alignment.

3. Sew the bag upside down, and the other two are like edges.

4. Fold the bag backwards. So the pencil case is ready, put a few pens in it and try it.

5. The zipper can be placed on the side, which is more convenient to use. Then use another color of cardboard to fold in half and cut out a suitable shape to make the lid of the pencil case, leaving about one centimeter below to apply glue and stick it to the pencil case.

6. You can add a small handle to make it easy to hang up. Just clip a strip of cloth when sewing the side seam.

Preparation material: Non-woven fabric 2mm thickness.

Sewing. Scissors.

Glue guns. Zipper.

Ruler. Steps:

1.First, draw a picture on the top of the non-woven fabric and cut it along the edges.

2.Find a contrasting zipper, you can also match the same Rangbi, feel free.

3.Let's start by sewing the zipper. Here I use the back stitch method, sewing one side first, and then opening the zipper to sew the other side.

4.Next, sew the bottom edge, align it, and sew the bottom with a flat needle. Then the sides are sewn and stitched with the seam seam method.

5.Finally, tidy up the zipper and sew both ends into the bag.

6.Prepare small decorations. Cut a few different pieces of non-woven fabric, this is all leftovers, and the leftover branches are made of things. Cut a rectangle, diamond, heart, feel free! You can also sew a sign plate, the kind of small logo, as long as you like!

Here's how to make a pencil case:

Material preparation: scissors, a table cloth, a lining cloth, double-sided tape, iron.

Operation steps: 1. Cut a table cloth, a lining cloth, and a piece of cloth with double-sided tape according to the size of the pencil case we want.

2. Press together the table cloth, cloth with double-sided tape and lining cloth in the order of the cloth, and glue them together with an iron.

3. Install the zipper, the front side of the table cloth is facing up, and the front side of the zipper is facing down to align the edge to fix.

4. Stitch the zipper and the table cloth after stitching, and it is best to use the "Z" stitch to lock the edge of the edge to prevent the cloth from spreading, or you can sew the edge by hand.

5. Press a bright line on the front.

6. Align the zipper and cloth on the other side, and repeat the process of 3 5.

7. Turn the cloth over and sew the front and back ends of the zipper together by hand to prevent the zipper head from falling off.

8. Fold the pencil case in half along the middle of the zipper, and cut a tooth opening at 1 2 places of the cloth to mark; After that, align the zipper with this 1 2, cut a tooth on each side of the fold to mark, and do the same operation at both ends.

9. Turn the pencil case over to the reverse side, bring together the three teeth and zippers, and fold them into the shape of the collapsed land calendar in the picture.

10. Stitch both ends, and you can also make a hem if you pursue perfection, so that you can't see the raw edge.

11. Turn to the front, this pencil case is done, hehe, isn't it very simple.

Here's how to make a handmade pencil case:Materials Tools: two pieces of cloth about 20-30 cm long, 30 cm long zippers, scissors, needles, thread, brushes.

1. In the inner part of the fabric, draw two cut outlines with a black pen.

2. Cut off the excess along the black outline and leave a gap of about 1 cm for edge sutures. Place the zipper between the front and back pieces of cloth and the inside of the fabric is facing outward, and the zipper is placed in line with the fabric. A small needle can be used to secure the position.

3. Sew the zipper and the fabric on it according to the red thread.

4. Turn back the front and fix both ends of the zipper, which can be fixed with a small needle.

5. The wide punch sews the edge of the front side material and the inner side material partially.

6. Stitch the bottom, sew the fabric along the white line, and then turn it over.