How to set up a router with a mobile phone, how to set up a Lingshi router with a mobile phone

1. First, connect the router and the modem to the power supply, and then use a network cable to connect the WAN port of the router and the LAN port of the modem (if it has been connected, you can ignore this step).

2. Then open the system settings of the mobile phone, open the wireless network on the system settings page, find the wifi name of the router and click to connect.

Router 3, then go back to open the mobile phone browser, enter the login address of the router in the browser address bar (you can view it at the bottom of the router).

5. After completing the wizard setting, you will enter the detailed setting page of the router, and the user can make relevant settings according to their own needs.

Here's how to set up a router on your phone:

1. First, connect the router and the broadband modem with a network cable, and the connection method is to connect the LAN port of the broadband modem with the WAN port of the router through the network cable.

2. After the hardware is connected, use the mobile phone to connect to the wireless signal of the router, then open the mobile phone browser, enter the login address and login password of the router, and select Quick Settings after logging in to the background.

3. Then fill in the broadband account number and password as required.

4. Then set the wireless name and password to save and then the router can be used normally.

After the router is powered on, the mobile phone searches for the wireless network, (the new route is generally the strongest signal and no password) after successfully connecting to the wifi, hit the mobile phone browser, on the back of the router, find the management address, and then enter the management address into the mobile phone browser, and the login interface of the router will come out.

Connect to the settings according to the routing instructions.

You can refer to the following methods for router settings:1Plug the broadband modem or home network cable into the WLAN port of the router, and then connect to the computer through the network cable or wireless network.

3.After entering the page, you will be prompted to enter the management account, which also needs to be found in the manual, and the general account password is admin

4.Click the Setup Wizard, follow the instructions on the page to set broadband without PPPOE dialing, and enter the broadband account password.

5.According to the prompts on the page, check the box to turn on the WiFi network, and set the password, when finished, click Next, and the device will automatically restart.

First of all, connect the router to the network cable and power supply, at this time, it will automatically generate a wifi signal without a password and use the mobile phone wifi function to connect to this network, which is when you can't access the Internet.

3 6**Enter the correct input directly into this interface, the password is the default of the system at the rear of the router, and you can customize it later.

Long Figure 5 6 and then click on the wireless settings, set the generated wifi, you can set the password or set the access IP to lock.

Click to complete the settings, click Save at the bottom of the right side to save the above settings.

Step 1: First open the wireless network settings in the mobile phone, if it is a new router, generally turn on the power, the router will automatically create an initialized wireless network, choose to connect directly, no need to care whether there is a network.

Step 2: Open the mobile phone browser, enter the login address of different brands of routers in the address bar, you can see the nameplate on the router body) and then open, and then a login interface will pop up. Enter the default initial username and password of the router here, and the general initial password is:

admin, the account name is also: admin, some do not use a password, you need to create one for the first setup.

Step 3: After logging in to the router settings interface, the setting method is the same as that in the computer. Find the router setup wizard first and follow the prompts to proceed to the next step.

Step 4: Open the setup wizard, click Next according to the prompts, the following is mainly to fill in the Internet broadband account and password provided by the operator, and finally you need to set up the wifi wireless network and password.

Step 5: When you get to this step, you need to choose the Internet access method first, generally we choose the PPPoe method (you can also choose to let the router choose it automatically), after choosing, click Next.

Step 7: The next step is to set up the wireless network, that is, to create a wifi network, mainly fill in the wifi name and create a wifi password (the password is recommended to be as complex as possible to prevent being rubbed on the network), after completion, click next to continue.

Finally, you can see the prompt that the setting is completed, click on the completion, the router will automatically restart, and the wireless router will be set up after the restart, and finally we will use the mobile phone to connect to the set wifi network to see if it can go online normally. If you can access the Internet normally, it means that the mobile phone has successfully set up the wireless router, if you can't access the Internet, please check whether the broadband account and password are filled in correctly in the sixth step.

How to set up a wireless router on a mobile phone How to set up a wireless router on a mobile phone [Detailed Introduction] Network equipment pconline IT encyclopedia.

Now you can live without a computer at home, but you can't live without wifi. Because mobile phones must use wireless Internet access! But if you don't have a computer and need to set up a router, you can only use your phone.

Now the manufacturer has added the way of setting up the mobile phone in the manual, but the manual is still a little simple. How to set up a wireless router on your phone? Today, we will talk about the methods and precautions for setting up TP routes (TL-WR886N) with mobile phones

The first is the connection method, the above figure shows the specific method, and you can use the mobile phone to set it up without considering the computer. There is a special place to pay attention to here,Don't turn on the power after the cable is connected,Don't turn on the power supply of the optical modem,Don't turn on the power of the optical modem,The important thing is to say three times as long as the routing is connected to the power supply You can have a mobile phone setting,Why the optical modem is not connected to the power will tell you!

Below take out our mobile phone and enter the WLAN option, scan, and find that there is a signal that is TP....The signal is open.

Prepare your phone to set up a wireless router.

Plug the router into the power supply and plug the broadband cable into the router's WAN port. If you have a broadband cable at home, you need to connect the broadband cable to the modem, and then connect it with the WAN port of the router with a network cable from another network card port of the cat. The connection method is as shown in the figure below

02 Now proceed to the wireless router setup:

Open the wireless network settings in your phone, and the new router will automatically create an initial wireless network after intervening in the power supply, which will be directly connected to this wireless network.

03Open the mobile browser, enter in the address bar, enter the IP and open it There will be a login prompt, the default account password is admin, log in after entering.

04After successful login, click Settings in the left navigation.

05 Open the setup wizard, mainly you need to fill in the Internet broadband account and password provided by the operator, and finally you need to set the wifi wireless network and password.

08Create a WiFi network, fill in the WiFi name and create a WiFi password (remember it yourself, but don't be too simple), and when you're done, click Next.

09After the setting is completed, the router will automatically restart, and the wireless router will be set up after the restart, and finally we will use the mobile phone to connect to the set wifi network.

Other routers open the mobile phone browser to log in to the IP address, there is an IP address on the back of the router, and there is also an IP address and password on the manual.

Open the browser, enter the IP address of the router in the ID address bar above, there is under the router, the general one is to click confirm, and the router account password is asked to appear, and there is a minimum router below, click to confirm.

There are three types after entering: broadband dial-up, dynamic acquisition and static. If it is connected to the bottom of the broadband modem, use the dial-up, enter the broadband account password, if it is connected to the router, use the dynamic to obtain, and now the new broadband modem is also obtained with the dynamic. Save or confirm, the next step is to ask you to set the wireless account password, save or confirm after setting.

Restart your router and you're ready to go.

Step 1; When the mobile phone is connected to the router, log in to the background settings interface of the router through the mobile phone browser, and the router login address is available on the back of the router, which is generally default.

Step 2: You need to enter the account and password of the router. Different brands have different account passwords, the following takes TP-Link as an example, the account and password of the old router are admin.

The new router is generally empty by default, you need to set a new password by yourself, and setting the router password can effectively prevent others from tampering with your router wifi password.

Step 3: Enter the background settings of the router, because the small font display on the mobile phone screen is not clear, you can double-click the screen to enlarge the interface. The steps below are exactly the same as setting up a router on your computer.

Open the setup wizard, click Next according to the prompts, fill in the Internet broadband account and password provided by the operator, and then set the wifi account password.

First turn on the router, connect the router wifi with your mobile phone, and then log in to the background settings interface of the router through the mobile phone browser, the general router login address is on the back of the router, you can view it yourself, and then enter the account password of the router, and then follow the prompts.

Restore the router to factory settings first (the hole on the back of the router is slightly thicker than a toothpick, insert it with a thin skewer and hold it for more than 5 seconds, and wait for all the lights to flash, then it will be restored).

First, enter the router, (open the UC browser on the mobile phone, enter OK in the address bar, OK if not.) In the login box, fill in the username and password admin or guest. On the left is the menu, and there are submenus under those + signs. ）

In the settings interface of the router, find the IP setting option of the WAN port on the menu, there are static IP, dynamic IP, and PPPoE, select PPPoE dial-up, fill in the broadband account and password (password), there are "automatic connection", "on-demand connection", etc., select automatic connection, save.

Second, on the settings interface of the router, find the DHCP settings on the menu, select "Enable", and save.

3. In the settings interface of the router, find the settings of the wireless connection, select "Open", fill in the wireless password, and note:

Encryption method: wep WPA2 PSK

Password setting: more than 32 digits plus letters with mixed case and case. to prevent rubbing the net.

Fourth, find the channel (some are called frequency bands) on the menu of wireless settings, select 6, and save.

Don't move anywhere else.

Fifth, bring it up separately, and after saving the settings, please don't forget to click the "Restart Router" button.

How to reset the router, don't hurry up and collect it, code up.

The basic way of the new router.

1. Look at the prompt on the back of the router, that is, what is the IP of this router.

2. Use the phone to search for the router signal (there is no password after factory reset), and the phone shows that it is connected. Then enter the browser of the phone, step 1 you see the IP address, click on the browser to go, the phone will automatically pop up in the browser to set the page.

3. Pop up the login of the router first, and remember this password, otherwise you will have to enter the login password when you log in again in the future.

4. In the setting wizard will be displayed on the left side of the setting page, (1) select PPPOPE dialing, and fill in the user name in the next step, the user name is the broadband account provided by the operator, and the password is the broadband password provided by the operator. (2) Set the wireless password, you can follow your favorite password. (3) Just save the wireless password.

Enter the routing IP address in the browser

Enter the broadband account and password provided by your carrier.

Select the pppope dial.

Set a wireless password.

Another problem is that the optical modem of the network operator now comes with its own routing function, if you also have such an optical modem at home, then the router you buy is almost the same, that is, in the "Setup Wizard - in the way of large network access"."Select "Dynamic IP or Static IP" and set the settings in a similar way.

1.There is a label under the router, and the label has the address, account password, and other information2Connect your phone to the router wifi, open the browser, enter the address on the label, enter the router login interface, enter the account password, and enter the router management interface.

3.You can set up the router, it is recommended that in addition to the wifi name and password, everything else is automatic.

4.If you forget the login password, you need to find the rust button at the network port of the router, press and hold for more than 5 seconds, the indicator light of the router will flash, and then release the button. Wait 5 minutes for the router to be reset, and then repeat the steps above.