Is it better to press the wall or the wall to press the floor with tiles? On what basis?

Tile is good for ground pressure wall. When the decoration owner friend contacts, he often asks the same question, that is, after all, the ground pressure wall is still good to press the ground, we don't need to press which one is better? Let him have a general understanding of the construction method first, so as to dispel his worries and worries.

First of all, the construction method of wall pressure, many people think that the wall pressure has the hidden danger of hollowing out the drum, and the bottom brick of the wall is pasted last, there is no support point, and it is easy to fall off. Is this the case in actual construction? There may be many masons who install the above steps to tile, but skilled masons will not do this, and if you really want to do this, it is not only a waste of time, but also may be difficult to avoid the hidden danger of falling empty drums.

The correct construction method of pressing wall bricks is: determine the level of the whole bathroom before masonry, and then use cement blocks to level with the first layer of tiles, use horizontal control of horizontal and vertical tiles to set flatness, floor tile paving will involve problems in wall pressure and wall pressure, under the condition of wall tiles with good strength and stability, remove the bricks under the wall tiles in time, and clean the edge of the bricks below with a rag. Since the surface of the floor tiles is 2-3 cm higher than the original wall surface, if the wall surface is flattened, the floor tiles are inserted directly into the wall tiles below.

Similarly, the floor tiles are pressed and the required seams are laid with the size of the required seams set aside. Pressure wall or wall pressure test on pavement construction is not much different, depending on the way you like, as for how to waterproof the effect is good, paving floor tiles are pasted, all need to do the joint waterproof construction of floor tiles, waterproof and beautiful joint treatment is not good, the method of paving floor tiles is not useful to paste tiles, it is said that the wall pressure or pressure to the wall. It's not good to do beautiful sewing:

The purpose of the seam is to beautify the brick joint to prevent water stains from seeping into the tile cracks or some small garbage, if the seam is not done, it will not only affect the decorative effect, but also affect the waterproofing.

Affect waterproofing: Most people think that if you do a floor pressure wall, water stains will penetrate into the joints between the wall tiles and the floor tiles, and when the wall tiles are under pressure, the wall tiles are on the floor tiles, and the water stains will only flow into the floor tiles along the wall tiles, which will not cause water penetration and affect the waterproofing. But is such evidence really true?

Does the difference between ground pressure wall and wall pressure really affect waterproofing? From the point of view of the pressure of the waterproof wall on the wall, whether the ground pressure is good or bad, the bathroom is an indispensable part of the construction process because of the problem of moisture, the fundamental reason for the waterproofing is not to pave the tiles, whether it is in the place of wall pressure or in the place of wall pressure, in fact, there will be the problem of water infiltrating into the brick joints, since it is inevitable, then what is the most important?

I think it's better to press the wall to the ground when applying tiles; The main basis is that the appearance of this will be higher, and it is more conducive to water access on the ground, and there is a good waterproof line.

The wall is well pressed to the ground. In this way, it can be better waterproof, there will be no water leakage in the later stage, it can be better lived, and there are no potential safety hazards.

It should be better to choose a wall to press the ground, so that the quality will be better, and there will be no falling.

After a long time of decoration contact, you will really encounter all kinds of strange problems, such as requiring bricklayers to use the wall to press the ground when they are asked to paste tiles. Asked him why he asked for this, and his answer was also very bright "said on the Internet"! Which is more correct, the ground pressure wall or the wall pressure ground?

So Jiang Pingping, who has been decorating for more than 30 years, will talk to you, what you said is not reliable!

Wall pressing and ground pressing wall are both a way of paving ceramic tiles, but there is no one that is good and which is bad. No matter which construction method is used, if the waterproofing is not done well, it will leak, so the wall pressing the ground and the ground pressing the wall are not the key. Therefore, no matter which construction method you use, as long as the waterproofing is done well, the water will not seep into the tile from the gap, and there is even a possibility of leaking downstairs.

Explaining why, let's see what difference is made in the construction!

The construction method of wall pressing the ground needs to be pasted with a special strip on the bottom side first, because the whole brick cannot be used, and the small strip is left in the obvious place to reduce the aesthetics; For example, the bathroom needs to have a slope of flowing water, and the bottom tile needs to be cut manually, which is definitely not as good as the original brick with neat corners. If there is a water leak, then you need to remove the wall tiles before you can repair the floor tiles. This will be very troublesome and not good for the owner.

When doing the construction of the ground pressing wall, we will start from the innermost first, and then slowly retreat outward, and do not go in for the time being after exiting, and can only enter after drying, the reason for this is that we are afraid of standing on the tile and then operate, and the sand cement stained on the sole of the foot may hurt the tile chrome.

If you follow the construction method of wall pressing the ground, at least the bottom of the wall tiles is to stand on the floor tiles to do construction, and it is cement and glue, and you have to go in and out of the bricks one after another, and you have to step on the floor tiles dozens of times. The probability of tile chrome injury has increased dozens of times, in case of unfortunate tile chrome injury, it is not to rework, is it to destroy the mood and delay the construction period!

Since the wall pressure and the ground pressure wall can achieve the same effect, in comparison, is the ground pressure wall will be more able to ensure the "safety" of the tile.

The process of renovation is cumbersome, and owners without professional knowledge are indeed easily frightened by some rumors on the Internet! What we need is to go to the renovation sites of different companies and ask the master on the spot, what is the reason for this? Don't let yourself become stubborn because of rumors, leave professional things to professional people!

Anyway, no matter what he does, as long as there is a problem, he still needs to bear the consequences!

It is best to choose wall and floor tiling for kitchen and bathroom tiling.

In the general kitchen and bathroom decoration, among these two ways of paving tiles, Xiaomei recommends choosing the wall to press the floor. Why did you choose this?

1. Because when the water splashes on the wall, it will flow down the wall to the root of the wall, and then drain down the floor drain; In the case of ground pressure walls, water flows directly from the wall to the root of the wall, which will seep into the waterproof layer in the long run, thus affecting the use of ceramic tiles.

2. The wall pressing will not affect the wall tiles during construction, and the construction period will not be delayed.

Therefore, through the above two points, the kitchen and bathroom bricks must be paved with the wall and the ground. Here I would like to remind you of one point: to reserve a certain height difference, generally the height of the entrance and the lowest floor drain, the height of the general door and the floor drain is best in 2 3 cm, so that the water on the surface can flow into the floor drain, so as to discharge.

Chuangqi starting point decoration.

If you use a floor-pressed wall, it will easily become trapped in the crevices and cause odors. And over time, the dry ash layer will also become moldy, and the moisture will be left along the dry ash layer to the door, which will cause the floor of other rooms to deform and arch.

In general, the overall aesthetics of the wall is better, and there will be no too large gaps with the naked eye.

The wall is well pressed and seamlessly connected, and the glass glue can be dotted without the baseboard.

If you want to reduce this hollowing rate, you need to wait for the tiles to dry before laying the wall tiles, but this should also pay more attention, although the hollowing rate becomes smaller, and the time will become longer. According to the thermal expansion and contraction, gaps of different sizes will also be formed, which will affect the appearance, and bacteria will increase between the gaps. The best way is to do a beautiful seam after the decoration, so that it is more perfect, as long as you find the right order, the construction is relatively simple, and the decoration effect will also achieve satisfactory results.

It's all good. When we are tiling, we must prevent hollowing, and the bathroom must be waterproof.

The ground pressure wall is better, so that the wall will not fall off very seriously, and the floor tiles are relatively stable after being paved, and the effect of suppressing the wall can also be achieved.

The wall is pressed to the ground. Because this kind of sticking is not easy to hollow out, and it is not easy to warp.

If there are no people who do not use tiles for decoration, then choose tiles for the walls. Don't think that a simple laying is over, but the order of laying is also important. For example, is the wall pressed?

Is it better to press the wall? Although it is a cliché, there are still many owners who don't know, especially those who are renovating for the first time! When you want to lay tiles on the walls and floors of your home, you need to lay tiles first, but you need to leave a blank space near the ground before you put the floor tiles.

After the floor tiles are laid, use tiles to lay the empty spaces on the wall. In this way, the wall tiles can press the floor tiles close to the edge of the wall, so it is called "wall pressing the ground". Generally, the ground pressed wall is the preferred paving method for bricklayers.

After all, construction is more convenient. In fact, if you want to lay bricks, it is better to choose the wall to press the floor, which is also the first way for many decoration companies.

The wall is pressed up by wall tiles, and the gap between the two generally exists on the façade, which is not obvious from the plane. But if you press the painting against the wall, the gap is usually on the flat surface, so you can see the gap at will, which lowers the value of the space by several levels. If tiling is to press the wall against the ground, the gap between the two generally exists on the vertical plane, and there is no obvious gap from the plane.

However, if it is pressed against the wall, the gap will be more obvious. From the outside, it is definitely the former that looks better.

In this method, by pressing the wall against the ground, the water on the wall will slowly flow into the floor drain along the slope of the floor tiles, so that it will not remain in the gaps. However, if the ground pressure wall is used, it is easy for water to flow into the gaps, and it is easy to produce unnecessary odors over time. The dry ash layer can also become moldy, and water will slowly flow down the dry ash layer to the door, affecting the floor in other rooms, causing the floor tiles or floor arching.

For the ground pressure wall, it is more troublesome to press the bricks, and there are more procedures. It is not the first tile laying, but the second tile operation. Wait for the floor tiles at home to be paved, and then paste the bottom wall tiles, so that you can press the floor tiles.

However, if it is a ground pressed wall, the wall tiles can be laid from the bottom bricks. Once the walls are covered, the floor tiles can be laid.

Generally, wall tiles are used to press floor tiles, which is to lay floor tiles first, and then paste wall tiles; If the wall tiles press the wall tiles, then the water will seep into the dry layer of the floor tiles along the gaps and destroy the waterproof layer.

Tile should be selected to press the wall to the ground, it will look particularly neat, special easy to take care of, and will also make the house look very warm.

Generally, it is better to have a ground pressure wall, which can prevent water from penetrating the ground. The basis is that through this decoration mode, the floor tiles can be saved, and the wall can look more flat, and the tiles can also be prevented from falling.

Whether bathroom tiles are attached to the wall or against the wall has always been controversial, as both methods are still used today. In fact, the first to introduce the pressure wall was the decoration company. The reason is that I went to hit the wall early in the morning.

To show its advantages, renovation companies have introduced the method of pressing walls to attract customers. So far, the basic requirements of normalized decoration companies are to press against the wall, while some small decoration companies and self-installation companies basically rely on the wall to do. As can be seen from the above figure, when choosing the paving method of the pressure wall, the gap in the inner corner where the floor tiles and wall tiles intersect is vertical.

When choosing the way to pave the pressure wall, the gaps in the inner corners are horizontal. As we all know, the most important problem of waterproofing in the bathroom is that the water flows downward, which means that vertical gaps are more likely to be flooded than horizontal gaps. No matter how good the waterproofing construction is in the early stage and how good the tile paving process is, in the water environment of the bathroom, the water will penetrate under the tiles along the gaps.

Over time, it is difficult for water to evaporate under the tiles. When fermenting slowly, there will be an unpleasant fishy smell, and choosing the method of building walls and pressing bricks can greatly reduce the amount of water seepage.

Even so, we find that if you don't specifically ask for pressure walls. Many bricklayers will also make pressure walls for you, and this is because the construction method of pressure walls is more difficult and time-consuming than pressure walls. If the floor tiles are applied first, he cannot step on them until the tiles are stable, and he will not be able to proceed with the next step of paving the wall tiles.

The construction period was delayed and the money was less, so he was naturally unwilling. The correct construction method is to copy the level, calculate the height of the tiles, leave a row of foot wall tiles, and then lay the wall tiles from the bottom to the top. The above-mentioned wall tiles are folded back after paving, and after the paving is completed, the last row of wall tiles under the feet is added.

Although this paving method will not delay the progress of the master's tiling, it can also press the wall to the ground. However, the master's construction technology and size calculation are very demanding. If the master's skills are not at home or careless, it is easy to cause the gap in the inner corner of the intersection of wall and floor tiles to be too large, and even the wall tiles cannot press the floor tiles.

Therefore, the most perfect way is to discuss with the tile master before laying the wall tiles. This method not only allows for a good arrangement of the water slope of the bathroom floor, but also facilitates the treatment of the intersecting inner corners of the laminated floor wall.

Tile is good for ground pressure wall. In this way, it will be particularly beautiful to post it, so that there will not be many problems when it is posted.