What to do if the manual ceramic filter mine has 16 water

There are many reasons for the increased water content of the filter cake of the ceramic filter, as follows:

Slurry characteristics: such as the treatment of ore with fine particle size and large mud content.

Changes in ore feeding conditions: the slurry concentration suddenly increases, and the slurry content increases.

Vacuum distortion: The vacuum system leaks, and the vacuum degree does not reach the normal range.

Ceramic filter plate: The ceramic filter plate is damaged and leaking.

Cleaning: Backwashing or combined cleaning is not up to standard.

Spindle transport**The spindle speed is adjusted faster.

Blockage: Ceramic filter plate is seriously blocked, etc.

Ceramic filter other questions, welcome to chat with me privately or look at my avatar.

Summary. Hello dear, happy to answer your <>

There may be the following reasons for the mining on some ceramic plates of the ceramic filter:1Ceramic plate quality problems:

Ceramic plates may have quality problems due to raw material problems in the manufacturing process or improper production processes, resulting in problems such as mining or cracking on the board surface. If this is the reason, then the broken ceramic plate needs to be replaced. 2.

The ceramic filter is used for too long: the filter will generally operate in a high temperature and high pressure environment, if it is used for a long time, the ceramic plate will age, resulting in the phenomenon of mine loss on the plate surface. If it is due to aging, then the ceramic plate needs to be replaced.

3.Improper cleaning leads to the mining of the plate surface: The ceramic filter needs to be cleaned regularly during use, if it is not cleaned properly or used too frequently, it may cause the surface of the ceramic plate to mine out.

Therefore, attention should be paid to the method and frequency when cleaning.

What is the reason for the mining on some ceramic plates of the ceramic filter?

Hello dear, happy to answer your <>

There may be the following reasons for the mining on some ceramic plates of the ceramic filter:1Ceramic plate quality problems:

Ceramic plates may have quality problems due to raw material problems in the manufacturing process or improper production processes, resulting in problems such as mining or cracking on the board surface. If it is the cause of this original model, then the car contains the need to replace the broken ceramic plate. 2.

The ceramic filter is used for too long: the filter will generally operate in a high temperature and high pressure environment, if it is used for a long time, the ceramic plate will age, resulting in the phenomenon of mine loss on the plate surface. If it is due to aging, then the ceramic plate needs to be replaced.

3.Improper cleaning leads to the mining of the plate surface: The ceramic filter needs to be cleaned regularly during use, if it is not cleaned properly or used too frequently, it may cause the surface of the ceramic plate to mine out.

Therefore, attention should be paid to the method and frequency when cleaning.

Therefore, it is necessary to follow the instructions for use and follow the correct operation steps when using it. As mentioned above, there are many reasons for the mining of some ceramic plates of the ceramic filter, which needs to be investigated according to the specific situation, find the problem, and then carry out corresponding maintenance and repair to deal with the leakage pants.

Hello dear! We'll be happy to answer for you. The reason why the ceramic filter does not absorb ore is that it is

If you suddenly do not absorb the slurry, the possible reasons are buried stupidly: 1Vacuum system failure, no vacuum or vacuum level does not meet the requirements.

The vacuum pump and vacuum pipeline, distribution head, ceramic plate, etc. should be checked for failure or air leakage. 2.Whether the feeding conditions change, such as slurry type, slurry content, fineness, concentration, etc.

3.After the combined cleaning is turned on, the suction effect may be good within 0 2 hours, it may decrease slightly within 2 4 hours, and it will definitely get worse and worse after 4 hours or even no suction. In this case, the backwash water pressure should be checked first (the instantaneous maximum water pressure should not be lower than whether it meets the requirements, and the joint cleaning should be stopped in advance (to ensure that the ultrasonic is normal and the amount of xiaosuan is sufficient) and the cleaning time of the joint belt should be extended.

4.Check the filtrate drainage. 5.

Of course, with the aging of the machine and ceramic plate, the sucking effect will gradually decrease.

What is the situation of not absorbing ore, is it an iron remover?

There are many reasons for the increased water content of the filter cake of the ceramic filter, as follows:

Slurry characteristics: such as the treatment of ore with fine particle size and large mud content.

Changes in ore feeding conditions: the slurry concentration suddenly increases, and the slurry content increases.

Vacuum distortion: The vacuum system leaks, and the vacuum degree does not reach the normal range.

Ceramic filter plate: The ceramic filter plate is damaged and leaking.

Cleaning: Backwashing or combined cleaning is not up to standard.

Spindle transport**The spindle speed is adjusted faster.

Blockage: Ceramic filter plate is seriously blocked, etc.

Ceramic filter other questions, welcome to chat with me privately or look at my avatar.

There is also to see how the configuration, different materials and configurations, the difference between the ceramic filter and the ceramic microporous vacuum on the ceramic plate to absorb the concentrate to absorb the water filter, the parameters are set according to it.

First, how large is the fineness of the material, resulting in.