What happens when the gas water heater comes out of the kitchen and the bathroom doesn t get hot wat

Shower angle valves. Question: Check if the shower valve in the bathroom is open, try to adjust the angle valve, and then wait a few minutes to test whether the water temperature is normal.

If the water temperature is still cold after the angle valve is opened, check whether there is hot water in the pipeline. Solution: If the angle valve is closed and the angle valve is opened, if not, check the gas pipeline.

Too much dirt in the shower hot water pipe: If there is too much dirt in the shower, causing too much water pressure, the water vapor linkage device of the water heater will turn off the hot water faucet of the water heater so that the water from the water heater will become brighter, so this water heater pipe, especially this pipe from the kitchen to the bathroom, must be dredged. Workaround:

Clean the gas water heater.

pipes, you can buy a special dirt cleaner for gas.

Precautions for the use of water heaters.

Use an electric water heater.

When the water temperature reaches the set value, the indicator light goes off, indicating that the power is cut off. In this way, the indicator light turns on and off, indicating that it is automatically holding warm.

Try to inspect the water heater once a year, mainly to check the heating status, button sensitivity, whether the drain valve is in good condition, and the electrical lines and brackets should also be carefully checked.

Clean the inner tank every six months, mainly to clean the scale on the heating pipe, you can also ask professionals to clean it, the water heater has been used for three years or more, and the heater and thermostat should be replaced once.

It is necessary to have a professional person do the replacement.

1.The pipes from the source water heater to the bathroom are clogged. Nowadays, there are many PPR pipes, and when they are hot, it is easy to cause pipeline blockage.

In addition, the rubber gasket of iron pipe or PPR pipe joint is also easy to be screwed due to quality problems, resulting in blockage of the pipe. Solution: Check whether the pipeline is smooth.

2.The water discharge time is short, and the pipe is too long. Before the hot water could flow, the washing was finished. Solution: Leave hot water for a while.

3.The cold water pressure is too high, or there is a problem with the mixing valve. Solution: Test the cold water pressure between the kitchen and the bathroom to see if the gap is too large. Or replace the mixing valve. Many times, the mixing valve is bought as bad.

1. It may be caused by the clogged filter of the faucet. 2. The ignition valve controlled by water pressure may be caused by insufficient water pressure. 3. It may be caused by the blockage of the hose under the kitchen faucet.

3. It may be caused by excessive use of hot water and insufficient hot water. 4. It may be caused by insufficient water. 5. It may be caused by the hot water pipe in the kitchen and the hot water pipe in the bathroom are not installed correctly.

6. It may be caused by the hot water faucet being turned on more and the water pressure being smaller. 7. It may be a normal phenomenon that the gas water heater does not have hot water in the kitchen caused by the lack of a shower in the kitchen. Suggested Treatment:

1. You can remove the faucet, turn the filter upside down, and backwash it with tap water. 2. A booster pump can be installed to adjust the water pressure to solve the problem that the gas water heater does not produce hot water in the kitchen and the bathroom is normal. 3. You can remove the hose of the water heater and then open the water heater to try, if the hot water can be discharged, you need to check and repair the pipeline other than the hose.

4. You can check whether the pipeline within the hose is unblocked, and dredge it if necessary. 5. When the hot water is insufficient, the time of using hot water can be appropriately adjusted or the specifications of the gas water heater can be replaced. 6. When the water is insufficient, you can contact the property.

7. The hot water pipe can be inspected and reinstalled if necessary to solve the problem that the gas water heater does not produce hot water in the kitchen and the bathroom is normal.

First of all, check whether the hot water pipeline is connected to the kitchen, and if there is a pipeline, check the hot water angle valve.

Whether it is opened, if it has been opened, open the mixing valve to the hot water position, if the water does not come out, the hot water pipeline will be blocked (PPR pipeline pipe fittings are easy to block). It is also possible that the valve under the kitchen is not open, or the water heater is not working, that is, there is no hot water.

In addition, there is hot water in the bathroom and no hot water in the kitchen, so you need to distinguish this situation carefully. It is very likely that the scale of the hot water angle valve under the bathroom basin is too thick and the angle valve is blocked, or the filter screen in the faucet on the basin is blocked. When these two things are blocked, the water output of the water heater is too small, and the water heater water film cannot be opened, and the water heater will naturally not work normally.

Solution: To replace the angle valve regularly, the angle valve must be replaced in 3 years, because the angle valve replacement is very cheap, so there is no value of maintenance, it is recommended to replace it directly. The faucet can be cleaned, and there is a net to filter impurities inside each faucet, which can be removed and rinsed with water and installed, and the problem will be solved.

When the water heater at home encounters the above problems, first remove the filter screen of the faucet and clean it, and replace the angle valve under the basin if it is not good to clean. Angle valves are generally sold in hardware stores.

What happens when the gas water heater comes out of the kitchen and the bathroom doesn't get hot water?

Hello, the gas water heater kitchen produces hot water, but the bathroom does not produce hot water for the following reasons: 1Blocked or leaking tubing:

In cold weather, the inside of the water pipes tends to freeze or clog, causing the hot and rotten water to not flow. At the same time, the water pipe itself may also leak due to aging or other reasons, which will affect the hot water**. This situation requires checking whether the pipes are unblocked and repairing the leaks in time.

2.Valves not open: Some gas water heaters are installed with multiple hot water outlets, such as kitchens and bathrooms, so you need to check if the valves are open.

If the valve is not opened, hot water cannot flow into the bathroom. 3.Mixing valve failure:

The mixing valve is a key component responsible for regulating the ratio of hot and cold water, and if the mixing valve is damaged or used incorrectly, it will cause the toilet to not function properly** hot water. In this case, it is necessary to check whether the mixing valve is working properly and replace the damaged mixing valve in time. 4.

Piping design issues: In some cases, there may be problems with the piping design of a gas water heater, such as the distance between the bathroom and the kitchen, or the length of the pipes. In this case, the piping scheme needs to be redesigned or replaced with a gas water heater with a higher flow rate to solve the problem.

To sum up, if the bathroom cannot ** hot water, you need to first check whether the pipes are unblocked, whether the valves are open, and whether the mixing valve is working properly. If none of the above solves the problem, consider redesigning the piping scheme or replacing the gas water heater with a larger flow rate.

What happens when the gas water heater comes out of the kitchen and the bathroom doesn't get hot water?

Causes of water pressure. The gas water heater opens the starting valve with water pressure and opens it automatically, but when the water pressure is low, the starting valve cannot be opened, and the gas cannot be ignited. The water heater is installed near the kitchen, and the water pressure in the kitchen is higher than that in the bathroom, so the kitchen can be used.

The pipes in the bathroom are long, and the water pressure is not enough. Therefore, it is not possible to leak and destroy. Seeking a professional maintenance personnel to change the pipes, or installing a small booster pump in the bathroom, can solve the problem.

This one is suitable for most water heater models such as Haier JSQ25-13UTS.