What should I do if the squatting toilet flushes and the water does not go into the water when the s

1. First of all, you can adjust the water inlet valve first, so that the water can be larger.

2. If it is because the water pressure is not enough, or because the pipes inside the toilet are not smooth and the flushing is not strong, you can test the water pressure of your home first. If the water pressure is not enough, you can set up a water tank on the roof, if it is a problem with the toilet, then change the toilet.

Squatting flushing is not energetic, this is not a matter of the urinal, but because the water pressure is not enough, under normal circumstances, the water pressure, the whole building from the bottom to the high water pressure will be a little lower, so in this case, not only yours, as long as it is on the same floor as you, the water pressure at home is low, and the water pressure is low The urinal will naturally be boring, my house is like that, my faucet takes nearly 30 seconds to receive a pot of water, and the first floor may be finished in a few seconds, so unless you buy a spare part to increase the water pressure, Otherwise, there is no workaround.

Common causes of toilet flushing weakness:

1. The side handle chain of the side press and side wrench toilet is long, which causes the water stop pad to stop the water quickly, although it has action. Solution: Please shorten it to the appropriate level. Or the top press bar of the top press toilet is low, resulting in the water stop pad moving but quickly stopping the water.

Solution: Open the lid of the water tank, reverse it, and loosen the nut of the pressure rod.

Adjust the length of the pressure bar to the right one.

Second, the water level of the inlet valve is low, resulting in weak water outlet.

The solution is to remove the inlet valve and remove the inlet valve buckle. Turn the inlet valve body counterclockwise. Then increase the height of the body accordingly.

Then rotate the inlet valve body clockwise and attach the buckle. Finally, install the inlet valve. Connect the filter and water inlet pipe, and the fault can be eliminated.

3. Ceramic hanging pollution:

The ceramic glaze of the toilet bowl is not smooth enough, which is easy to hang dirt, and it will also cause the flush to be unclean.

1. If there has been a similar situation, it is a product quality problem and the glaze material is not good, so let the merchant come to deal with it.

2. In the past, it could be cleaned, but now if it can't be cleaned, clean it frequently, and don't use too corrosive washing liquid, which will damage the ceramic glaze and make it easier to hang dirt in the future.

Fourth, the solution of ceramic hanging pollution:

In general, it is good to brush directly with a toilet brush. If it is always easy to get dirty, a good toilet with ceramic glaze is better, use cheap toothpaste, be careful to be white, not the transparent kind, and then scrub with the green or blue rough side commonly used for dishwashing. If you haven't cleaned it for too long, you can use a steel wool ball to gently wipe it first.

However, the use of steel wool balls and decontamination powder will damage the ceramic glaze, so it is recommended not to use it.

That's when the sewer is blocked, you buy a leather picker and try it with a skin picker. If it is not good, connect a water pipe (thick) at the water valve, and then put it in the water under the squatting toilet, plug it with a towel around the pipe, and then turn the water to the maximum to see if it can be flushed away. You can also buy a pipe dredging agent to try (but I haven't tried this method).

The look of the skin:

Cut it off with a hanger and stick it in the direction of the sewer.

Hello dear, happy to answer your <>

Answer: Foot valve squatting toilet flushing weak solution In real life, sometimes there will be weak squatting and stool, so the following steps can be handled: 1. Reinstall the pipeline, the squatting toilet has a small impulse, which is likely to be caused by the abnormal installation of the pipeline, and then the pipeline needs to be reinstalled to adjust.

2. Modulate the water press rod to increase the amount of water. 3. Modulate the water inlet valve, the water level of the water inlet valve is low, it will lead to the weakness of the water outlet, you can remove the water inlet valve and reinstall the modulation to the corresponding height. The outlet of the flush tank is blocked by other parts of Hengxun or the opening is not complete, check it; There is something in the sewer pipe that is blocked or obscured, or there is a bend in the bucket that causes the water to flow poorly.

The water valve switch is not suitable, the opening is not complete or the opening is too slow, if it is a pull line, the line is not too long. When installing, the rubber sealing sleeve plug is too in, so that the water inlet of the squatting toilet is blocked, this situation will be more troublesome to deal with, you need to reinstall the squatting pin this toilet, if you clearly understand the important requirements for installing the flush tank, tell the installer in advance to pay attention, so as not to cause unnecessary trouble.

1. Reinstall the pipeline, the impulse of the squatting toilet is small, which may be caused by the abnormal installation of the pipeline, and the pipeline needs to be reinstalled before adjustment; 2. Adjusting the pressure rod of the hydraulic press can increase the amount of water; 3. Adjust the inlet valve, if the water level of the inlet valve is low, the water will become weaker, the inlet valve can be disassembled and reinstalled, and adjusted to the corresponding height.

1. Reinstall the pipeline, the impulse of the squatting toilet is small, which may be caused by the abnormal installation of the pipeline. At this point, the piping needs to be reinstalled before adjustment.

2. Adjusting the pressure rod of the hydraulic press can increase the amount of water; Adjust the inlet valve. If the water level of the inlet valve is low, the water will be weak. The inlet valve can be removed and reinstalled and adjusted to the corresponding height.

3. If the situation does not improve, it is necessary to continue the investigation. First, check if the drain of the tank is blocked by other components or the key lever is too short, resulting in slow and very little drainage.

4. Check whether the sewer pipe is blocked or clogged, whether there is an elbow, etc. Resulting in poor water flow. If so, make appropriate adjustments based on the actual geographical environment.

5. Check whether the switch of the water inlet angle valve is appropriate and whether it can be fully opened. **In public places with a large amount, it is impossible to fill with water within 2 minutes, and the angle valve can be fully opened.

Pay attention to the flushing tank of the squatting toilet, pay attention to the connection between the elbow and the squatting toilet when installing, and the installation position should be appropriate, otherwise it is easy to be blocked, resulting in poor drainage valve.

Summary. Hello dear, I am happy to answer for you: the treatment method of squatting pit flushing without pressure:

First of all, check the reason why the flush is not pressing, if it is caused by the tank drain valve is not fully opened, in this case, only open the tank drain valve to the maximum. If the depth of the flushing pipe inserted into the water inlet is too deep, resulting in throttling, in this case, the flushing pipe should be appropriately pulled outward, and then flushed after fixing. In addition, blockages can also cause the flush to run out of pressure, requiring thorough unclogging of the waterway.

How to deal with the pressure of squatting pit flushing.

Hello dear, I am happy to answer for you: squatting pit flushing without pressure treatment method: first check the reason for the flushing without pressure, if it is because the water tank discharge valve is not fully opened, in this case, only need to open the tank discharge valve to the maximum.

If the depth of the flushing pipe inserted into the water inlet is too deep, resulting in throttling, in this case, the flushing pipe should be appropriately pulled outward, and then flushed after fixing. In addition, blockages can also cause the flush to run out of pressure, requiring thorough unclogging of the waterway.

1. Reinstall the pipeline, the squatting toilet has a small impulse, which is likely to be caused by the abnormal installation of the pipeline, so you need to reinstall the pipeline. 2. Modulate the water pressure rod of the water presser, and the water volume can also be increased. 3. Modulate the water inlet valve, if the water level of the water inlet valve is low, it is easy to have weak water outlet, you can remove the water inlet valve and reinstall it to the corresponding height.

1. The less water in the tank, the weaker the toilet flush and the weaker the whirlpool, just open the tank cover, reverse it, loosen the screw nut, and adjust the length of the pressure rod to the appropriate solution.

2. The water level of the inlet valve is low, and the effluent quality is poor. The specific solution is to remove the intake valve, remove the intake valve clamp, turn the intake valve body counterclockwise, then lengthen the height of the valve body accordingly, and finally turn the intake valve body clockwise. These faults can be solved by securing the clamps, installing the intake valves, and connecting the filters and intake pipes.

3. When the flush is weak and there is no whirlpool, if you see more dirt at the outlet, you can clean it with baking soda or white vinegar. It does not harm the ceramic glaze of the toilet bowl and can be cleaned very quickly.

If the water coming out of the tank is not urgent, it may be that the drain outlet of the tank is a little blocked, dredged, if it is slow under the water of the pit after flushing, it may be that the sewage pipe is a little blocked, this needs you to check whether it is a precursor to the blockage of the main pipe of the sewage pipe in your house.

The squatting toilet does not necessarily flush urgently, as long as it can flush down the stool and toilet paper.

What do you want your hands to do?