The shower water is getting smaller and smaller, what s going on? What should be done?

In our family, the shower is basically used when bathing, so that we are very helpful in the shower or corresponding to cleaning, but after using it for a long time, the water of the shower is getting smaller and smaller, so many people are very curious, and they usually don't touch it, so why does this phenomenon occur? Today, I will talk to you about how to ensure that the water flow is sufficient in the shower of the sanitary system. <>

The reason why the shower water becomes smaller is multifaceted, sometimes it may be because our water pressure does not meet the requirements, many times we live in high-rise buildings, we need pipe pressure to transport water up, then sometimes the number of people using water increases, the water pressure does not meet the requirements, and the corresponding water output of the shower is reduced. At this time, we want to ensure the flow of water from the shower, so we can add a booster pump to our own water inlet pipe.

Make the water more sufficient. On the other hand, it may be because of the long-term use of tap water, which is mixed with impurities accumulated for a long time, blocking the water outlet, resulting in a smaller amount of water output, at this time we should try to disassemble the entire shower system to see, observe whether the water inlet is blocked, if blocked, we should clean it up in time, if necessary, contact the decoration master to help us repair. <>

There is also a situation where impurities in the water block the water outlet of the shower, which is often calcium carbonate at this time.

We can buy white vinegar and use vinegar to clean the spout of the shower. At the same time, we should pay attention to avoid direct contact with the pipe part of the shower to prevent corrosion, so that after cleaning, it can effectively alleviate the scale and increase the water output. If necessary, we can also take the whole shower out of the pipe and soak it in vinegar.

The above is about how to solve the shower blockage, when we buy the shower, we can also appropriately choose the more popular pressurized shower nozzle on the market, which can effectively ensure the water output, but if there is a significant reduction in water flow, then this time it is necessary to carefully detect to prevent the pipeline from clogging and bringing more serious consequences.

The water flow of the shower becomes smaller, which may be caused by the presence of debris in the shower, resulting in a smaller water flow, or it may be caused by damage to the rubber ring. The solution is very simple, if the rubber ring is damaged, just replace it with a new one, if there is debris, you can use a needle to pierce the small hole of the shower to remove the debris.

1.Whether the water pressure in the customer's home has become lower than before: If so, it is necessary to check the water supply line and pressure with the water company.

2.The line valve connected to the water heater opens smaller: open the inlet valve wider.

3.Due to the high floor and low water pressure of the water source, the water output is significantly smaller after the pressure reduction of the mixing valve: at this time, it is recommended to connect a booster pump between the water supply valve and the water inlet of the water heater.

4.The water outlet of the mixing valve may be stuck with small sand and dirt, resulting in a small amount of water output. The mixing valve is congenitally insufficient, the diameter is small, and the throttling leads to a smaller water output

Try the inlet end of the detachable mixing valve, connect it to the water supply valve of the water heater with a hose, or connect the sprinkler hose directly to the hot water outlet end of the water heater, and identify the quality of the mixing valve according to the water output of the sprinkler; On the premise that the water pressure of the water source is satisfied, the mixing valve of the full-size brand can be replaced. 5.Improper installation, deformation of the rubber ring, uneven or too thin outlet pipe joints, mismatch between the hose and the shower, etc

Select the appropriate hose and shower according to the specifications, replace the rubber ring, and reinstall it.

The first point is likely to be ** blocked should be checked in time, the second point should be solved, is to see if there is a break inside, should go to a new one, the third point is less and less water, it is very likely that there are impurities in it, the fourth point can go to a professional maintenance place to repair it.

Maybe it's because it doesn't work. You can use a needle to prick those little holes. Or take the shell off and take a look. Is something clogged?

It's the people on the same floor who take a bath and don't have anything to do, it's not a water pressure problem, so why? What is the reason? How to solve it?

After that, I found a professional electrical repair master to repair it, it turned out to be a problem with my family's water heater, and now the water is back to normal! The new installation of the water pressure problem is more likely, the old shower does not feel that it has become smaller than before, in addition to the comparison of the water from the shower and others, the water of the faucet, you can also judge the problem of sprinkling in the water for about 2 hours, re-water for a while, and then wipe with a clean cotton cloth, the dirt will be discharged. If it hasn't improved, it may be a problem with low water pressure, you can change to an additional shower or water pressure <>

One reason is that the shower has been used for a long time, and limescale impurities have blocked the sprinkler head, or the pipe. Because of the scale of the water heater, some of it will enter the shower, and there are impurities, sand and rust in the water itself. There are two situations in which the water pressure of the shower head is small, one is the water supply, the water pressure is small, for example, the highest floor of the building you live in is the sixth floor, and you live on the fifth floor, so that if you install a complete set of showers, the water will not be large; Another situation is that the water supply pressure can be, we all know that after the water is heated, it will produce a lot of scale, and it will block the shower head for a long time, so that the water output will be reduced when taking a bath, and the water inlet valve is a problem

If the inlet valve is not unscrewed, the water flow will be relatively small, find the inlet valve under the water heater, open it completely, and open it to the maximum, and there will be no problem. The installation height of the shower shower is generally about 40 cm between the shower head and the human head. It is too close to use and inconvenient, it is easy to touch the shower, and the water temperature is lowered too far, wasting hot water.

But I later found out that many people did not do it right, they unified this height, but ignored that there are two kinds of showers, one is a fixed sun shower and the other is a movable hand shower, in fact, the height of the two is different, <>

There are many reasons why the water from the shower is getting smaller and smaller, the more common reason is that the sediment and dust enter the inside of the shower and cause the shower to be slightly blocked.

The probable cause is low water pressure. Due to the high living floor and low tap water pressure, the water output of the natural shower will be smaller and smaller when bathing, and it may be that the internal resistance of the shower will be caused by the use of time for a long time, so that the shower will produce less water.

The water from the shower is getting smaller and smaller because the filter in the shower is blocked, because although the water looks clear, there are actually magazines that are filtered in the filter, so it should be cleaned regularly so that the shower will not be small.

The reason why the shower head has little water is even it!

The shower is an indispensable part of the shower, and the amount of water in the water heater is directly related to it. The amount of water produced by the shower becomes smaller during use, which will not only affect the shower, but also affect the mood. Let's take a look at the reasons for the low water output of the shower and what are the solutions to the low water output of the shower

One. What is the reason for the low water output of the shower

1.It may be that the valve of the pipe connected to the water heater is opened small, resulting in a small amount of water from the shower, as long as the valve is opened wider.

2.The low water pressure leads to a small water output, which may be the high residential floor and the low water pressure of the water source, and then the water output becomes smaller after the pressure reduction of the mixing valve, etc., and a booster water pump can be connected in series between the water supply valve and the water inlet of the water heater.

3.It may be that the water output is smaller due to a stain on the outlet of the mixing valve. You can try to disassemble the inlet end of the mixing valve and connect it to the water supply valve of the water heater with a hose; Or connect the sprinkler hose directly to the boiling water outlet of the water heater, and distinguish the quality of the mixing valve through the water output of the sprinkler.

4.It may also be that the installation is not reasonable, resulting in the deformation of the rubber ring, and the outlet pipe joint is not even or too thin. If the hose is inconsistent with the shower, select the appropriate hose and shower according to the specifications, replace the rubber ring, and reinstall it.

Two. What to do if the shower has a small amount of water

1.With a toothbrush

Some showers can adjust the amount of water, it has a soft circle in the middle, close it tightly, and then turn it in the opposite direction (or clockwise) to remove it, and then use a toothbrush to gently brush off the dirt inside, clean it and install it again.

2.Poke with a needle.

You can also poke it along the water outlet of the shower with a needle to make the dirt fall off the inner wall of the water outlet hole until there are no impurities on the hole wall, and then clean it with water.

3.Soak in vinegar.

Dirt in the shower is formed by the accumulation of carbonic acid compounds in the water, which can be neutralized with acids. Use white vinegar when cleaning to avoid corrosion on the surface of the shower, and soak it for a little more time to completely remove the dirt.

It may be because the water pressure is not good, or it may be because the shower holes are blocked, or it may be because there is a lot of limescale in the water, which will clog these holes in the shower. Finally, it may be because the quality of the shower is not good, so the parameter water is small.

It may be because the pipe valve is relatively small, it may be because the water pressure is relatively low, it may be because there are stains at the water outlet, it may be because the quality of the shower is relatively poor, it may be because the water outlet is not smooth.

If the pressure is low, or there is a problem with the water outlet of the shower, it may be blocked, it may be that the switch is not fully turned on, and there are too many water stains.

It is because of the blockage, the power is relatively small, the installation position is wrong, the deformation occurs, and the internal resistance is relatively large, which will lead to a relatively small water outlet.

There is a problem with the connected line valve, or it may be that it is opened relatively small. It may be that something is blocked, so there is a problem of very little water. It could also be that the cement inside is blocked. It could also be that the water pressure was too low, so it couldn't be sprayed, or it could be that the shower was broken.

What is the reason for the low water pressure of the new shower! Hello, I am glad to answer for you<> the reasons for the low water pressure of the new shower are as follows: because of improper installation or deformation of the rubber ring, the water output of the shower is small, or even no water, it can be reinstalled and replaced with the rubber ring.

The purchased shower does not match the hose, resulting in an incorrect connection where the water does not flow into the hose and the water does not flow out. There is limescale or foreign matter inside the shower that blocks the water outlet, resulting in the water flow cannot pass through the shower and the water is small or does not come out. In addition, it may also be due to improper adjustment of the shower, resulting in weak water and weak lying on the stomach.

Because the original water supply is small, it cannot meet the water output of the shower, and the water output is insufficient and boring, and a booster pump can be installed. The shower regulates the inflow of hot water into the mixing tank, allowing the hot water to flow out quickly and accurately. Automatic thermostat:

The thermostatic mixing valve has the function of automatic constant water temperature, after the outlet water temperature is set according to the actual needs, the outlet water temperature can be quickly reached and automatically constant, and is not affected by the change of cold and hot water inlet pressure, temperature or outlet water flow, so as to solve the problem of hot and cold water temperature in the bathing process. When there is a change in the inlet pressure, temperature or outlet flow rate of hot and cold water, the change in the outlet temperature is within 2 years. Anti-scald and anti-cold shock:

The thermostatic mixing valve has the function of anti-scald and anti-cold shock, in the process of bathing, when the cold water is suddenly interrupted, the mixing valve can automatically close the hot water within a few seconds, which plays a role in the safety protection of anti-scalding; When the hot water is suddenly interrupted, the thermostatic mixing valve can automatically turn off the cold water within a few seconds, playing a role in the safety protection against cold shock. Experienced professionals should be hired to carry out the construction and installation. When installing, the shower should try not to bump with hard objects, and do not leave cement, glue, etc. on the surface, so as not to damage the surface plating luster.

Special attention should be paid to the installation after removing the debris in the pipeline, otherwise it will cause the shower to be blocked by the pipe debris, which may affect the use. Hope mine can help you <>

Do you have any other questions?

The treatment method of small shower water flow is as follows:

Tools Ingredients: booster pump, toothpick, white vinegar.

1. Open the main valve of the large water pipe. If the amount of water in the shower head increases significantly, it is likely that the original water pressure is too small, resulting in a small amount of water output from the shower head.

2. Disassemble and clean the shower head. Most shower heads are small because of the blockage of debris, disassemble the shower head, rinse the dirt and sundries inside, and install it again, the water output will definitely be much larger.

3. Soak in vinegar and detergent. Soak the entire shower head in white vinegar or stain remover for about 15 minutes, then wash the surface with a rag after taking it out, then turn on the shower again, select the water outlet mode with a large amount of water, and drain the softened stain with water.

4. Poke the shower with a toothpick. After a long period of use, the water outlet hole of the shower head is easily blocked by impurities, which affects the water output. Poke each shower outlet hole with a toothpick, and the amount of water will definitely increase.

5. Install the booster pump. If it is determined that the water pressure is low due to the high floor level, you can choose to install a booster pump.

6. Replace the shower head. If the above reasons have been investigated, and the effect is not obvious after rectification, then you can only choose to replace a new shower head.