What is the installation method of the toilet bowl and what are the detailed installation steps of t

Step 1: Check the levelness of the sewage pipe with the ground.

Before the toilet is installed, it is necessary to conduct a comprehensive inspection of the sewage pipe, check whether there is any blockage of sediment, waste paper and other debris in the pipe, and also check whether the ground is horizontal before and after the toilet is installed.

Step 2: Determine the center of the sewer pipe.

Before installing the toilet, you should first confirm the center of the sewage pipe, the confirmation method is to turn the toilet over, and then determine the center on the toilet drain, and at the same time draw a cross center line at the center, and the cross center line should extend to the bottom of the toilet and the feet around it.

Step 3: Fix the toilet.

When fixing the toilet, you should first align the cross line between the toilet bowl and the ground sewage outlet, ensure that the toilet is installed horizontally and then press the sealing ring tightly, and finally you can install the screws and decorative caps of the feet.

Step 4: Do a good bottom seal.

After fixing the toilet, a special sealing ring should be installed on the sewage outlet of the toilet, or a circle of glass glue or cement mortar should be coated around it, and the ratio of cement to sand is 1:3.

Step 5: Install the tank fittings.

Before installing the fittings of the water tank, you should put water for 3-5 minutes to flush the pipes. After ensuring the cleanliness of the water pipe, the angle valve and the connecting hose are installed, and then the hose can be connected to the installed water tank fittings for the water valve, and the water source is pressed at the same time.

Step 6: Debug the inspection.

After the toilet is installed, it is necessary to inspect the toilet bowl to check whether the inlet valve and seal are normal, whether the location of the drain valve is flexible, whether there will be jamming and leakage, and whether the inlet valve is equipped with a filtration device.

How to install a toilet at home.

Step 1 Before the toilet is installed, a comprehensive inspection of the sewage pipe should be carried out to see if there is any mud, sand, waste paper and other debris in the pipe.

At the same time, it should also be checked whether the ground of the toilet installation position is horizontal, and if the ground is found to be uneven, the ground should be leveled.

Step 2 Flip the toilet bowl and determine the center on the toilet drain.

At the same time, draw a cross centerline, which should extend to the bottom of the toilet bowl around the feet.

Step 3 Align the reticle line on the toilet bowl with the ground drain outlet and install the toilet bowl horizontally.

At the same time, press the sealing ring tightly and install the anchor screws and decorative caps.

Step 4 Install a special sealing ring on the toilet drain.

Step 5 Drain the water for 3-5 minutes to rinse the pipes to ensure the cleanliness of the water pipes.

Then install the angle valve and connecting hose.

Then connect the hose with the installed tank fitting inlet valve and press the water source.

Step 6 Check whether the water inlet and sealing of the water inlet valve are normal.

Check whether the installation position of the drain valve is flexible, whether there is jamming and leakage, and whether there is leakage to install the filter device of the inlet valve.

Accessories: 1 pair of plastic bearings, 1 pair of screws, 1 pair of lower lock gaskets, 1 pair of lower lock bolts, 1 pair of decorative covers.

Step 2: Put the screws on the plastic bracket and place them on the mounting holes of the toilet;

Step 3: Put the washer on the plastic nut, on the one hand, press and hold the top of the screw, turn the nut on the screw from the bottom of the toilet bucket to 9, so that the bracket can also be slightly looser, the screw is longer, and it must be rotated for a period of time;

Step 4: Two small holes in the toilet lid are aligned with the support column and inserted vertically. Adjust the toilet lid plate on the front, back, and left so that it fits the toilet bowl perfectly. The sides are then bolted and locked in hand so that the support does not move.

Step 5: Open the toilet cover, press the front button of the toilet cover, remove the cover vertically, and use a screwdriver to strengthen the screws so that they are fully tightened;

Step 6: Place the stainless steel decorative toilet lid on the stand.

Step 7: Replace the cover again and check whether the deceleration function of the toilet cover is normal and complete. That is, the installation of the entire toilet lid is completed.

30 to 40 cm.

Ask how many millimeters from the floor tile should the drain pipe butted to the toilet dove?

Answer: There is a sealing ring at the bottom of the toilet drain, and the source sealing ring is put on the sewage pipe just to dock with the toilet outlet. Therefore, when installed on site, the sewer nozzle is about 1cm from the ground.

Question: I disagree with the installer, whether the installer generally cuts the drain pipe and the floor tile flat bundle to install the toilet correctly.

Detailed drawing of the toilet bowl

Tools: toilets, angle valves, hoses, rulers, rags, pencils, glass glue.

1. Open the packaging of the toilet, take it out, and then connect the hose to the back end of the toilet (the installation accessories of the toilet are mainly angle valves and hoses, which can be purchased by yourself or negotiated with the merchant).

2. Take a ruler to measure the distance between the wall and the ground outlet. After measurement, the distance between the bathroom wall and the sewage outlet is 400mm, which is exactly the 400 hole spacing of the toilet. If the distance is 300mm after measurement, you can choose the 300 hole spacing on the toilet.

In special cases, a shifter is also required.

3. Take a rag and wipe the ground around the sewage outlet clean to facilitate the installation of the toilet.

4. Install angle valves. After that, place the toilet bowl on top of the drain outlet, and after comparison, use a pencil to draw a line along the edge of the toilet bowl to facilitate installation. Then, place the toilet aside.

5. Along the pencil line, put the glass glue, put the toilet on the glass glue, and compare it with the ground sewage outlet. After attaching it, the overflowing glass glue from the toilet bowl is tightly packed and kept beautiful.

To install the toilet seat, you first need to remove the old toilet seat, then prepare the newly bought toilet seat, install the fixing plate with screws, and then push the toilet seat parallel to the fixing plate, the specific steps are as follows:

1. Remove the old toilet seat

Open the toilet seat, there are two buttons at the bottom of the toilet seat, everyone press and hold the toilet lid button to lift the toilet seat. Then we remove the decorative cap from the toilet seat fixture, loosen the screws of the fixture with a screwdriver, and remove the fixture. After the old toilet seat was removed, we wiped the toilet clean with a rag.

2. Buy a new toilet seat

When buying a new toilet seat, we need to use a ruler to measure the hole spacing, length and width of the toilet seat, and buy a new toilet seat according to the measured size. After the smart toilet seat is delivered to your door, we will take out the toilet seat and its accessories, check whether the toilet seat and accessories are damaged, etc.

3. Install the fixing plate

We put the fixing plate of the smart toilet lid with the hole of the toilet lid, we put the expansion screws and the card slot together, and then put them into the screw holes of the fixing plate, after we adjust the position of the card slot tooth wire, tighten the expansion screws with screws and fix the fixing plate.

4. Install the toilet cover

We press and hold the unlock button of the toilet lid while pushing the toilet lid parallel to the fixing plate, and then release the unlock button. After the toilet lid is fixed, we turn off the toilet valve, use a wrench to loosen the toilet valve hose and remove it, and then install the filter on the water valve, and connect the hose to one of the ports of the water filter. Then use a hose to connect the toilet lid to the water filter.

The toilet is an indispensable device in the family bathroom. To install the toilet properly, you need to follow these steps:1

Prepare tools and materials, including toilets, water pipes, connectors, seals, screws and nuts, etc. 2.Turn off the faucet and disconnect the power to the water pipe.

3.Place the toilet in the correct position, making sure that the four feet of the toilet are placed smoothly. 4.

Connect the water pipe to the toilet bowl and secure it with screws and nuts. 5.Place the seal between the water pipe and the toilet bowl to prevent water leakage.

6.Connect the water pipe to the downpipe and secure it with screws and nuts. 7.

Turn on the faucet and check the water pipes for leaks. 8.If everything is in order, you can install the toilet lid on the toilet bowl and secure the toilet to the ground.

Note: During installation, attention should be paid to safety to avoid injury. If you are not familiar with the installation process, it is recommended to have a professional do the installation.