How to install a toilet and what are the steps to install a toilet

Although toilet installation is simple, it is important to master the installation method of the toilet, and only the toilet with accurate installation can make people feel at ease. Let's take a look at the general process of toilet installation. 1. Check the levelness of the sewage pipe and the ground Before installing the toilet, the sewage pipe should be comprehensively inspected to see if there is mud and sand, waste paper and other debris in the pipeline, and at the same time check whether the ground of the toilet installation is level.

2. Determine the center of the sewage pipe Flip the toilet, determine the center on the toilet outlet, and draw a cross center line, which should extend to the bottom of the toilet around the feet. 3. Fix the toilet Align the cross line between the toilet bowl and the ground sewage outlet, keep the toilet installed horizontally, press the sealing ring tightly, and install the anchor screws and decorative caps. 4. Do a good job of sealing the bottom Install a special sealing ring on the toilet drain, or put a circle of glass glue (putty) or cement mortar around it, and the ratio of cement to sand is 1:

3。5. Install water tank accessories and rinse the pipe for 3-5 minutes to ensure the cleanliness of the tap water pipe; Then install the angle valve and the connecting hose, then connect the hose with the installed tank fitting inlet valve and press the water source. 6. Debugging and inspection Check whether the water inlet and sealing of the water inlet valve are normal, check whether the installation position of the drainage valve is flexible, whether there is jamming and leakage, and whether there is leakage and install the water inlet valve filtration device.

Hope it helps.

How to install a toilet at home.

1. Before installing the toilet, it is necessary to check whether there is a blockage in the pipe and whether the sewage pipe used meets the specified standards.

2. After the inspection, determine the installation position of the center of the pipe and the bottom of the toilet to start the installation. Place the front side of the toilet bowl up, install the sealing ring at the drain outlet, and then install and secure the toilet bowl.

3. After fixing, put a layer of glass glue on the connection between the ground and the toilet, and then connect the water pipe with the toilet hose, and the installation is completed.

In our home life, the toilet is our essential cleaning equipment, but sometimes the toilet merchants who buy it in the market will not install it for you. Some toilets seem simple to install, but we also need to master some methods and toilet installation processes. Let's take a look at the toilet installation methods and the introduction of the toilet installation process.

What are the toilet installation methods.

1. The step is to determine the center of the sewage pipe. Turn the toilet over. Be careful at this time. Determine the center of the drain pipe on the toilet drain and draw a cross center line, which should extend to the foot around the bottom of the toilet.

2. Fixing the toilet is also crucial. Determine where to install the foot screws on the bottom of the toilet. Traces can then proceed to begin.

Use an electric drill to drill the installation holes and embed the plastic rubber sleeve of the expansion screws. Align the reticle line between the toilet bowl and the ground drain outlet, keep the toilet installed horizontally, and press the sealing ring tightly, and install the anchor screws and decorative caps.

Toilet floor drain vegetable sink wash basin bathtub dredging maintenance and installation free consultation**::400-017-1110

3. In order to prevent water leakage, do a good job of sealing the bottom. Useful for future use. Install a special sealing ring on the toilet drain outlet, or put a circle of glass glue (putty) or cement mortar around the sewage pipe, and the ratio of cement to sand is 1:

3。Then install the angle valve and the connecting hose, then connect the hose with the installed tank fitting inlet valve and press the water source.

Toilet installation process in the bathroom.

1. Check the leveling between the sewage pipe and the ground.

Before installing the toilet, a comprehensive inspection of the sewage pipe should be carried out to see if there is mud, sand, waste paper and other debris in the pipeline, and at the same time check whether the ground of the toilet installation position is horizontal.

2. Determine the center of the sewage pipe.

Flip the toilet bowl over to determine the center on the toilet drain and draw a cross center line that extends to the bottom of the toilet bowl around the feet.

3. Fix the toilet.

Align the reticle line between the toilet bowl and the ground drain outlet, keep the toilet installed horizontally, and press the sealing ring tightly, and install the anchor screws and decorative caps.

4. Do a good job of bottom sealing.

5. Install the water tank accessories.

Drain the water for 3-5 minutes to rinse the pipes to ensure the cleanliness of the water pipes; Then install the angle valve and the connecting hose, then connect the hose with the installed tank fitting inlet valve and press the water source.

6. Debugging and inspection.

Check whether the water inlet and sealing of the inlet valve are normal, check whether the installation position of the drain valve is flexible, whether there is jamming and leakage, and whether there is leakage to install the filter device of the inlet valve.

The above introduction to the toilet installation method and the toilet installation process is here first, and the toilet installation method is understood.

Toilet floor drain vegetable sink wash basin bathtub dredging maintenance and installation free consultation**::400-017-1110

1. Check the levelness of the sewage pipe and the ground, you must check whether there is any blockage of sediment, waste paper and other debris in the sewage pipe, and at the same time, you must also check whether the ground is horizontal before and after the position where the toilet is installed, and the unevenness needs to be leveled.

2. Determine the center of the sewage pipe and confirm the center of the sewage pipe, the method is very simple, that is, turn the toilet over, and then draw a cross center line at the center of the toilet outlet, and pay attention to the lower cross center line to extend to the bottom of the toilet and the feet around it.

3. To fix the toilet, first align the toilet with the cross line of the ground sewage outlet to ensure that the toilet is installed horizontally and then press the sealing ring tightly, and the next step is to install the screws of the anchor and the decorative cap to fix the toilet.

4. After sealing the bottom and fixing the toilet, it is necessary to install a special sealing ring at the sewage outlet, or coat a circle of glass glue (putty) or cement mortar around it, and the ratio of cement to sand is recommended to be 1:3.

5. Install the water tank fittings, and put 3-5 minutes of water to flush the pipe. After ensuring that the tap water is clean, the angle valve and the connecting hose are installed, and then the hose is connected to the installed water tank fittings for the water valve.

6. Debugging and inspection, the last step is to inspect the toilet, check whether the location of the drainage valve is flexible, whether the inlet valve and the seal are normal, whether there is any jamming and leakage, pay attention to see whether the inlet valve is equipped with a filtering device, etc., if not, it is recommended to install.

Before the toilet is installed, check whether there is any blockage of sediment and debris in the sewage pipe, and whether the installation ground is level. 2. Determine the center of the sewage pipe and draw the center line of the cross. 3. Determine the center on the toilet drain and draw a cross center line.

4. Determine the installation position at the bottom of the toilet, use an electric drill to lay the installation hole, and embed the expansion screw. 5. Install a special sealing ring (i.e., steaming flange or rubber flange) on the sewage outlet of the toilet or put a circle of glass glue (putty) or cement slurry around the sewage pipe, the ratio of cement and sand is 1:36, align the cross line on the toilet with the ground cross line, install the toilet, and then put a circle of glass glue (putty) or cement mortar at the bottom of the toilet.

The ratio of cement to sand is 1:3, and the toilet installation should be kept level. 7. Screw the screws on the toilet mounting holes.

8. Install and debug the water tank accessories. After installation, connect the water source, check whether the water inlet and sealing of the water inlet valve are normal, check whether the drainage valve and the installation position correspond to each other, whether the installation is tight, whether there is leakage, check whether the length of the button switch chain is appropriate, whether the switch is flexible, whether there is a chance to jam, and check whether there is a leakage to install the water inlet valve filtration device. 9. If you find any abnormalities in the trial process of adjusting the toilet, please refer to the "Common Faults and Treatment Methods of Toilet Tank Accessories, Check and Deal with It".

10. After the toilet is installed, it should wait until the glass glue (putty) or cement slurry is solidified before it can be used with water. The curing time is generally 24 hours.