-
The washing machine can't block the water, so in your case, there may be a water leakage, first check whether the machine has water leakage, and then rule out other reasons.
-
The washing machine can not be blocked, the water may be caused by some parts falling off or loose poor contact, etc., if you can't simply troubleshoot, it is recommended to find maintenance personnel to deal with it.
-
If you can't block the water, there must be a problem, call the manufacturer's customer service or the seller's customer service, and let them see what's going on.
-
So if you wash the machine, you can't block the water, maybe it's because the water quota is broken, and then you fix it, or there is a poisonous water valve, and something is blocking it.
-
The washing machine can't be blocked, the washing machine can't block the water, it may be her fault, you can find a repair, go fix it.
-
The learning machine can't block the water, the washing machine can't block the water, there must be a leakage, and workers should be hired to repair it in time. I can solve this problem.
-
If the washing machine can't block the water, it means that your washing machine is broken, and you should find a professional master to help you repair your washing machine. Let's see what's going on.
-
If the water washing machine can't block the water, it means that it is broken inside, and find a maintenance person to check it.
-
There must be something that can hold the water back, and if it doesn't, I think you've missed it, or there's something else you haven't noticed.
-
In this case, it is most likely that his teaching mat is leaking and needs to be looked at by a professional.
-
If the washing machine can't block the water, then it proves that the flow rate is a bit too large.
-
The washing machine can't block the water, you can look at the manual, or you can call the ** on the manual to contact the local repair 3.
-
If you can't block the water, then you should quickly find a professional repairer to help you repair it.
-
If this washing machine can't block the water, alas, if it can't block the water, it is estimated that it will be broken, just fix it, it's really like this.
-
If the water system can't block the water, you can take a look at it, is there a fault in this aspect of the pathway? Or maybe it's a little leaky or something.
-
Maybe level 11 is broken, just dismantle that machine and take a look.
-
Here, you can directly contact the after-sales service of the washing machine to help you deal with it.
-
Learning machine poison mushroom water, I think the grandfather who reads should be a broken glue pen tube.
-
The reasons are: 1. The suction stroke of the pump is large. For example, in some places with deep water sources, we should pay attention to the suction lift on the manual when using it to ensure that the operation is carried out within the suction stroke.
2. The speed of the pump is not high. The mechanical failure of the pump itself and the loosening of the impeller and pump shaft fastening nut or the deformation and bending of the pump shaft can reduce the speed of the high-pressure pump, resulting in insufficient power and inability to absorb water.
3. The resistance in the water flow inlet pipe is too large, and we must ensure that the length of the pipe and the bending place of the pipe are within the operating range when using the cleaning machine to dig the cloth.
4. The impeller of the high-pressure pump is seriously worn.
5. The bottom valve of the high-pressure pump is faulty. Including the foot valve cannot be opened or the air filter on the foot valve is blocked.
6. There is air retention in the hail ear pipe and pump body of the inlet water.
-
The reason why the water does not come out of the washing machine may be due to a clogged inlet filter or a damaged part of the cong rock pump body. The cleaning machine is mainly a machine that uses a power device to make a high-pressure plunger flush pump to produce high-pressure water to flush the surface of the object.
-
Serious nozzle wear: The ultra-high pressure cleaner equipment is prone to damage to the grinding wheel of the nozzle in the process of use, and when the wear is more serious, Huisen should replace it in time to avoid affecting the normal use of the equipment.
-
The reason why the washing machine does not produce water may be that the compressor of the washing machine has broken down, which cannot make the washing machine properly discharge the water out of the washing machine.
-
If your detergent doesn't get water, the main reason is probably that there is a problem with the power part inside. Check whether it is a problem in this regard, and then Yamahashi will make the next judgment. Do tremble.
-
1) Air is sucked into the high-pressure water pump or water inlet line. At this time, we only need to pull the trigger of the high-pressure water gun, reduce the working pressure of the high-pressure washer, and run for a period of time until a stable pressure is generated. (2) Insufficient water supply.
At this time, it is necessary to check whether the pressure of the water source is sufficient. Some pressure washers do not have a self-priming function. At this time, adding a booster pump can solve the problem.
3) The water supply filter is blocked, and the water supply filter can be cleaned. Car washing machines are divided into automatic car washing machines, self-service car washing machines, coin-operated car washing machines, and automatic car washing machines. It is a machine that uses a computer-controlled brush and high-pressure water to wash the car.
The reasons why the car washing machine does not absorb water: 1. Water seal leakage; 2. The inner bowl is not vacuum; 3. There may be problems with the pump head, the seal is not good, and there is air in the pump head; 4. It may be that the piston is not airtight; 5. It is also possible that the regulator is broken. Workaround:
Pull the trigger of the high-pressure water gun to reduce the working pressure of the high-pressure cleaner, and run for a period of time until there is a buried consolidation pressure. Check that the pressure of the water source is sufficient. Some pressure washers do not self-prime.
At this time, adding a booster pump can solve the problem. The water supply filter is clogged and only the water supply filter can be cleaned. Treatment method of non-absorbent water in the new car washing machine:
1. First check the water inlet, including the water inlet pipe, filter, etc. Drain back to the hall to make sure there are no infarctions. If it doesn't absorb water, open it and feel it to see if there is any vibration.
If there is a vibration, you may wish to absorb water, and the unilateral infarction will leak. If there is no vibration, it should be that the motor in the pump is broken. 2.
Then remove the high-pressure pipe and connect it after the machine comes out of the water (if the pipe has not come out of the water at this time, you can test the connection to the tap water first); If the gun and the tube are connected and the water does not come out, the gun head is passed. 3.The pump head can then only be taken apart for careful inspection.
Generally, the plunger position is stuck, and there may be problems such as water seal and oil seal. If the hands-on ability is not good, it is recommended to take it to the store to repair.
-
What's the deal with car washes that don't absorb water?
-
If you find that the cleaning machine does not absorb water during the use of the cleaning machine, it is generally caused by the following reasons.
1. Water seal air leakage;
2. The inner leather bowl is not vacuum;
3. There may be a problem with the pump head, the seal is not good, and there is air in the pump head;
4. It may be that the piston is not sealed;
5. It is also possible that the regulator is broken.
Solution: Pull the trigger of the high-pressure water gun, reduce the working pressure of the high-pressure washer and run it for a while until the consolidated pressure occurs. Check whether the pressure of the water source is sufficient, some pressure washers do not have self-priming results, then adding a booster pump can solve the problem.
The water supply filter is infarcted, and the only way to do this is to clean the water supply filter.
The new car wash machine does not absorb water disposal method.
1. Check the water inlet end first, including the water inlet pipe, filter, etc., to ensure that there is no infarction. If you don't absorb water, open it and touch it to see if there is vibration, if there is vibration, you might as well absorb the water and the one-sided infarction is about to leak, if there is no vibration, it should be the motor in the pump is broken.
2. Then remove the high-pressure pipe, turn on the machine and wait for the water to come out of the machine before connecting it (if the pipe is not out of water at this time, you can also test the tap water first); If you connect the gun and the tube, you can pass the tip of the gun without water.
3. Then you can only disassemble the pump head for detailed inspection, and the general plunger position is stuck, so you might as well have problems with water seals and oil seals. If your hands-on ability is not good, it is recommended to repair it in the shop.
-
Hello answer, glad to answer for you. In fact, it is because there is a lack of water in the pump casing where the pump is cleaned. The principle of high-pressure washer cleaning is to use a high-pressure pump to produce high-pressure water, and then heat it to a high-temperature hot water steam of 150 degrees through a heating coil, and then flow to the nozzle through the pipe, and finally the nozzle will turn the high-pressure and low-flow water into a low-pressure and high-flow jet, so as to impact the surface of the object to be cleaned.
The solution to the problem of not absorbing water: 1. Remove the high-pressure pipe, and then turn on the machine and wait for the water to come out of the machine before connecting it. 2. If it still doesn't come out of the water, pass the gun head.
-
There are several reasons why the cleaning machine does not absorb water.
Pump failure. There is a fault in the electrical control.
-
1. Check whether the nozzle is worn; If it is worn, replace the nozzle; 2. Whether the filter is blocked, and replace the filter for cleaning goods; 3. Take off the nozzle, start the machine, check whether the water sprayed by the spray is normal, if the water is normal, then install the nozzle, check whether the machine has pressure, if there is still no pressure, it means that the pressure regulator is damaged or the seal of the high-pressure pump is damaged.
4. If the water supply is insufficient, it is necessary to check whether the pressure of the water source is sufficient, and some high-pressure washers do not have the self-priming function, so adding a booster pump can solve the problem. 1. The performance of external factors is mostly unclean water supply, insufficient water supply, and blocked water supply filter, which is a very common failure, and the general user will not notice it, thinking that the cleaning equipment is faulty, and the reason is not detected when the equipment is checked.
Solution: Increase the pressure of the water source, if the tap water supply is insufficient, it is recommended to find a container to store the water first, which is sufficient for the intake. If the filter is clogged, clean the water supply filter, and if the filter is damaged, replace it with a new filter to prevent foreign matter from entering the pressure washer and causing equipment failure and clogging.
2. There may be many kinds of internal factors, such as water seal damage, check valve damage or foreign body cushion can not be opened and closed normally, pressure regulator valve can not be adjusted normally, plunger wear, and plunger chamber, swash plate, spring damage may cause insufficient pressure. Solution: Carefully inspect the parts of the pressure washer and replace the damaged parts.
-
There are three possible reasons why the cleaning machine cannot absorb water:
1. Check whether the pressure handle is loose or there is artificial decompression, if there is the first movement of pine tung, it is recommended to restore.
2. Take off the head of the copper roller pump to see if the tip of the water-blocking copper rod with a spring is worn, and if it is worn, it should be replaced in the accessories store.
3. Remove the screw of the reciprocating piston pump in the body, whether the rubber ring on it is damaged, and replace the spare parts of the cleaning machine according to the degree.
-
The motor forms a negative pressure inside the container and sucks the water in, if it is not sealed, it will not absorb water, and the solenoid valve said by the master upstairs is not opened.
-
Is it not water or no drainage?
Entrust interests, or hold the handle.
You have been away from home for a long time, there is evidence that the sewer is blocked, you shouldn't pay, it's like this many times upstairs in our house, and no one at home doesn't pay.
Vigerates micro water car wash is a new generation of car washing tools, also known as mobile car wash, environmental protection car wash, high-pressure car wash, waterless car wash, is a car wash method that uses convenient mobile and non-sewage car wash equipment to the parking space cleaning service. Micro-water car washing refers to a micro-water car washing method that adds car wash wax to the water. Less water consumption, will not cause pollution to the place, first wet the body, and then use a towel sponge to scrub a way, micro water car washing equipment with casters below, can move freely in a large range, low water consumption, each car only needs about eight liters of water, it can not only clean the surface of the car can also carry out multi-project car maintenance function, from the outside to the inside can be comprehensively cleaned, this micro water car washing machine can achieve a comprehensive service. >>>More
It's called "Zhang Yujiao".
Jiaojiao, female, whose real name is Zhang Yujiao, was born in 1986, a member of the "Unnamed Group", and an actor under Benshan Media. "Unsung Group" won the runner-up in the finals of CCTV's 2011 "Avenue of Stars". She made a wonderful appearance in the 2013 CCTV Spring Festival Gala sketch "I want to go to the Spring Festival Gala" and was well received. >>>More
The grass kneading machine integrates the cutting of grass and kneading grass, with high output, simple structure, convenient operation and wide processing range. It can process forage such as orange stalks, cotton stalks, beans, wheat oranges, pasture grasses, and various grains, and can also crush corn cobs for planting oyster mushrooms and other practical mushrooms. >>>More