Wuling Rongguang handbrake did not let go and drove eight kilometers, does it matter

It doesn't matter if you want to do a self-test first. 1. Pull the handbrake to death, and there is no problem with hanging the 1st gear starting engine to turn off. 2. If it does not turn off, it means that the brake pads of the handbrake have burned out and need to be repaired. **The shop (Buddha Rain Qingfeng 777) can help you, I hope it will be.

Hello, important, hope to build the brake assembly as soon as possible, hopefully!

It is very serious, because the handbrake is generally the rear wheel brake, if you do not let go of the handbrake to drive, it is easy to wear the brake pads of the rear wheel, affect the braking performance of the vehicle, and it is easy to cause the overheating of the brake hoop when driving for a long time, and when it is serious, the rear wheel will be locked or there will be no braking effect directly.

The principle is as follows: the professional name of the handbrake is the auxiliary brake, which is different from the principle of the brake, which is connected to the rear brake shoe by using a steel wire to brake the car. Long-term use of the handbrake will cause plastic deformation of the wire, and since this deformation is irreversible, long-term use will reduce the utility, and the travel of the handbrake will also increase.

The handbrake is complemented by a recovery spring. When the handbrake is pulled up, the spring is elongated; The handbrake is released, and the spring returns to its original length. When the handbrake is used for a long time, the spring will also deform accordingly. When any part is used for a long time and frequently, there is a phenomenon of reduced utility.

Nowadays, many cars have a handbrake alarm system, that is, the handbrake driving computer will alarm for a long time during normal driving.

Wuling Rongguang's handbrake light not only prompts the driver that the handbrake is not put down, if the handbrake light is still on in the case of the handbrake is down, it proves that the vehicle is missing brake fluid, in this case, it is necessary to add brake fluid in time to avoid vehicle brake failure, the specific operation steps are as follows:

1. Open the door of the Wuling Rongguang cab.

2. Pull the hood switch on the left side of the driver's leg of Wuling Rongguang.

3. Lift the hood of the engine of Wuling's glory upwards.

Fourth, use the support rod to support the hood of Wuling Rongguang to ensure that the support is firm and avoid danger.

5. Add brake fluid to the MAX line in the brake fluid pot of Wuling Rongguang.

Hello, there are usually two fault points, the handbrake switch and the brake fluid switch, you check whether the brake fluid is less, there is a plug-in connector to see if the light is still on, the switch is not bright, check the handbrake switch, the method is the same as above. Hope it helps.

Wuling glorious handbrake.

The light not only indicates that the driver has not put down the handbrake, but also proves that the vehicle is missing brake fluid when the handbrake is lowered.

In this case, it is necessary to add brake fluid in time to avoid brake failure of the car and sail, and the specific operation steps are as follows

1. Open the door of the Wuling Rongguang cab.

2. Pull the hood switch on the left side of the driver's leg of Wuling Rongguang.

3. Lift the hood of the engine of Wuling's glory upwards.

Fourth, use the support rod to support the hood of Wuling Rongguang, Hengyuan to ensure that the support is firm to avoid danger.

5. Add brake fluid to the MAX line in the brake fluid pot of Wuling Rongguang.

Summary. In this case, it will definitely have a certain impact on your rear brake pads, because you drive 10 kilometers, then your rear wheels are likely to cause ablation of brake pads and brake drums, so in this case, it is recommended that you still find a repair shop, remove your rear brake pads and brake drums to see if the ablation is serious, if the ablation is more serious, this needs to be replaced, otherwise there is no way to guarantee the braking effect in the later stage. And if you have abnormal tire pressure now, you should see if the tire wear of the rear wheel is serious, which may be due to tire wear, which causes the tire pressure warning light to turn on.

There is an abnormal tire pressure on the dial.

In this case, it will definitely have a certain impact on your rear brake pads, because you drive 10 kilometers, then your rear wheels are likely to cause the brake pads and brake drums to be ablated, so in this case, it is recommended that you still have to find a repair shop without a bridge, remove your rear brake pads and brake drums to see if the ablation is serious, if the ablation is more serious, this needs to be replaced, otherwise the brake effect in the later stage is not guaranteed. And if you have abnormal tire pressure now, you should see if the tire wear of the rear wheel is serious, which may be due to tire wear, which causes the tire pressure warning light to turn on.

You can adjust this! How to adjust:

1. Method: If you find the handbrake.

's braking efficiency or sensitivity is not ideal, which can usually be solved by adjusting the handbrake's operating copper cable. At the junction of the bottom of the handbrake handle with the copper cable (generally covered by interior parts) there is an adjustable compensating mechanism with a wrench.

Loosen the lock nut.

You can stretch the length of the brake copper cable. However, the adjustment mechanism of some cars is located at the bottom of the car, and if it is inconvenient to adjust, it should be handled by professional maintenance personnel.

2. Precautions:

Many people think that if you encounter the braking system.

If it fails, you can pull the handbrake to slow down, but in fact, this practice is wrong. Because the handbrake mechanism is not precise, the braking force on the left and right sides is unevenly distributed, and it is easy to pull the handbrake at high speed to make it hide the rear wheel on one side of the collapse, and the side slip occurs, which is very dangerous. The correct way to do this is to slow down by downshifting, and only pull the handbrake to stop the car when the speed is reduced.

Generally, you can adjust the adjustment nut in the middle of the lower part of the car, and you can also adjust the nut that is not after the handle-type hand brake.

Hello: Debugging according to the following steps:

1. First of all, the handbrake adjustment screw can be found at the arch of the rear pedal position of the BAI vehicle.

2. Open the gap of the dao, and you can pat the grinding to see the handbrake special adjustment nut.

3. The lower part of the hand brake adjustment bolt can be used to fix.

4. After that, use a wrench to fix the lower part of a bolt.

5. After that, use a wrench to tighten the upper part of the bolt to adjust the tightness of the handbrake, clockwise twisting will tighten the handbrake, counterclockwise will adjust the release of the handbrake.

6. Finally, adjust the positions on both sides of the left and right Gaohezheng appropriately.

Hope it helps:

Hello: Debugging according to the following steps: 1. First of all, you can find the handbrake adjustment screw at the arch of the rear pedal position of the vehicle.

2. Open the gap, and you can see the handbrake adjusting nut. 3. The lower part of the hand brake adjustment bolt can be used to fix. 4. After that, use a wrench to fix the lower part of a bolt.

5. After that, use a wrench to twist the upper part of the bolt to adjust the tightness of the handbrake, twisting clockwise will tighten the handbrake, and counterclockwise will loosen the handbrake. 6. Finally, adjust the position of the left and right sides to fit the celery. Hope it helps:

When the car starts, if the handbrake is not lowered, the buzzer will sound an alarm to remind you to put down the handbrake while driving.