How to adjust the lights of Wuling Light? How to adjust the Wuling Rongguang headlights

Adjust the left and right of the high beam headlights.

Adjust the height of the high beam headlights.

Adjust the left and right of the low beam headlights.

Adjust the height of the low beam headlights.

1) High beam refers to the intensity of the light according to the distance of the filament when the vehicle is driving at night, and the light emitted will shoot out in parallel at its focus, and the light is more concentrated, the brightness is larger, and it can illuminate very high objects. High beams can improve the line of sight and expand the field of view. Adjust the intensity of the light according to the distance of the filament, the high beam will shoot out in parallel at its focal point, the light is more concentrated, the brightness is larger, and it can shine on very high objects.

Outside of its focal point, (between 1x and 2x the focal point), the light emitted by the low beam light is in a divergent state and can illuminate a large area of objects in the vicinity.

2) The irradiation distance of the low beam is about 30-40 meters. According to the experiment, when driving at a speed of 55 kilometers per hour at night, the brakes were immediately applied when the situation was found, and the stopping distance was exactly 30 meters.

That is, when the situation is found within the range of low beam illumination, it stops immediately, and there is no gap between the car and the object. Of course, this is when the vehicle condition, road conditions and the driver's response are good, if the speed is higher than this, the vehicle condition, road conditions are poor and the driver's fatigue reaction time is long, the result can be imagined. Therefore, it is important to control the speed of the vehicle when driving at night.

When using high beams on a flat, wide, well-sighted road, the speed of the vehicle can be appropriately accelerated; And when the car encounters uneven road surface or turning or bridges or narrow roads or intersections and other complex situations, it should slow down and slow down, and the speed is generally controlled within 40 kilometers per hour.

There are two adjusting screws behind the headlights, one adjusts the height and the other adjusts the left and right, all of which are controlled at the same time for low beam and high beam, which can be adjusted with a Phillips screwdriver, and the car is best adjusted close to the wall, so that it is easy to see the change.

If you've just changed your headlights, sorry, your headlights are the worst kind. Dimm. You drive the car to the wall, and the lights are on the right tone. The car is adjusted. Just like that, a few screws you slowly type. I can't say anything about it. Because there are too many headlights now.

It can be adjusted by:

1. Pull the wrench in front of the engine compartment of Wuling Hongguang, and the engine compartment can be opened.

2. After that, you can use the bracket to support the engine compartment cover and change the gear.

3. After that, you can see the inside of the engine cabin, and you can find the headlight adjustment knob in the position shown in the picture.

4. After that, you can use a screwdriver to adjust the knob. Turning the high beam upwards will change the line to determine the distance, and adjusting the high beams downwards will make it closer.

5. After that, you can check whether the headlights are suitable to adjust the distance in front of the car.

1. When you enter the cab, you can see the control lever of the headlights.

2. Rotate the left knob to"off"to turn off the light gear.

3. Adjust to the position shown below to open the gear for the width indicator light.

4. Adjust to the position shown below to open the gear for the near-virtual light.

5. The middle knob can adjust the fog light switch.

6. Turn the entire gear lever forward or backward into a turn signal gear.

7. Hit the entire gear lever forward to open the first high beam, and hit the back to open the single high beam gear.

Wuling Rongguang ( Check price |The length of the model reaches 4 meters, the width reaches 1615mm, and the height reaches 1900mm, compared with the traditional micro-passenger (within meters), the length, width and height are comprehensively increased, and the large size brings large space, Wuling Rongguang has a larger ride and cargo space than the ordinary extended micro-bus.

The method of adjusting the Wuling Rongguang headlights is as follows:

Prepare to adjust the most important tool for headlights, hexagonal board, this thing is not expensive, cheap more than a dozen yuan a set; Some models also use Phillips screwdrivers, boards, and pliers.

select clever alternative tools where appropriate; The tools used for marking, preferably chalk or oil pens, are the easiest way to find and sell a stone that can be marked; Open the bonnet to find the adjustment bolt, which is positioned differently due to the different headlight designs of different models, but most models are behind the headlight assembly.

Many models of adjustment bolts are toothed around, it is easy to judge, the center is hexagon or hexagon + Phillips screwdriver slot, and the wide and bright part of the model is hexagon nut; It should be noted that some lights are integrated with low and high beams, so there are generally two adjustment bolts for adjusting height and width; The independent low and high beam headlights can adjust the height of the low beam and high beam respectively, and the width can also be adjusted, so there may be 3-4 adjustment bolts; So when adjusting, don't come up and screw hard, first fine-tune to try what each bolt is responsible for, and then adjust the bolts that need to be adjusted.

Tighten the bolt with one hand while making adjustments while carefully observing the light tangential lines on the wall.

If the light on the right is too high before, adjust it according to the position of the light on the left, and the height is basically the same, and vice versa. In order to be more accurate, you can make a mark on the tangent of the headlight at the normal height, and at the same time make a mark according to the normal height in the illuminated area of the headlight on the other side, and then adjust, which is also much more convenient; When adjusting, pay attention to the rotation amplitude should not be too large, little by little, to ensure accuracy. After the adjustment, try to drive a circle, take care of the road, look at the car in front, and observe whether you can see the road clearly without shaking the people and cars in front of you.

To emphasize, adjusting the headlights yourself is only a remedy, not a remedy! Because the headlight illumination height of each car is set, the headlight height is in line with this standard when leaving the factory, if your car is the headlight that is unchanged after leaving the factory, there is no need to adjust it at all. (Photo by photo:.)

Chen Yalan.

Wuling Glory is 4 meters long, 1615 mm wide and 1900 mm high, compared with the traditional micro-passenger (within meters), the length, width and height have been comprehensively improved, and the large size brings a large empty room. Wuling Glory has a larger passenger and freight space than ordinary extended micro-passengers.

The adjustment method of the height of the Wuling Glory headlights is as follows:

The most important tool for adjusting headlights, hexagonal socket board, this thing is not expensive, and it costs more than ten yuan a set. Some models also come with a Phillips screwdriver, planks, pliers, and a suitable selection tool; It is best to use chalk or oil pen to mark the ruler. The easiest way to do this is to find a stone that can be marked.

Open the hood and locate the adjustment bolt. Because different models have different headlight designs, the position of this bolt is different, but most models are behind the headlight assembly.

Many models have teeth around the adjusting bolt, and it is easy to tell whether the center is hexagon or hexagonal + Phillips screwdriver slot, and some models are outer hexagonal nuts. It should be noted that some headlights integrate low beam and high beam, so there are generally two adjustment bolts for adjusting the height and width. The headlights with independent low and high beams can adjust the height of the low and high beams respectively, and can also adjust the width, so there may be 3-4 adjustment bolts; So, when adjusting, don't just tighten it, first micro-tune what each bolt is responsible for, and then adjust the bolts that need to be adjusted.

When adjusting, tighten the bolt with one hand and carefully observe the change in the tangent position of the lamp on the wall. If the light on the right was too high before, adjust the height according to the position of the light on the left, and vice versa. In order to be more accurate, you can make a mark on the tangent line of the headlight at the normal height, and at the same time make a mark on the illumination area of the headlight on the other side according to the normal height, and then adjust it, which is much more convenient; When adjusting, be careful not to rotate too much, and ensure accuracy step by step.

After adjusting, try to drive the car around, look at the road, look at the car in front of you, and see if you can see the road clearly without shaking the people and cars in front of you.

Emphasize that adjusting the headlights yourself is only a remedy, and it is not recommended to adjust them yourself! Because the headlight height of each car is set, the headlight height meets this standard when it leaves the factory. If your car leaves the factory in perfect condition, there is no need to adjust it at all.

First turn on the radio and press the up button on the right button, so that the display will change from a band to a time display. Then immediately press the upper button of the circle again, the display of the hour flashes, at this time use the left and right directions of the inner button on the left, adjust up or down. After the adjustment, press the upper button on the right side, the display of the time division will flash, continue to use the left and right directions of the left round button to adjust the size to the smallest.

After tuning, press the upper button on the right to return to the band FM display.

"Wuling Light" is the first domestic advanced technology in the country, and independently developed with the support of the Pan Asia Automotive Technology Center, a joint venture between General Motors and SAIC. "Wuling Light" is not equipped with airbags under the premise, the first batch of domestic models that have passed the "frontal collision occupant protection" test certification, and in accordance with the most advanced international automotive technical specifications for comprehensive test verification of the whole vehicle, fully representing the advanced technology of the product.

Contains a total of 1 displacement, there is a manual transmission with a total of 1 transmission options, maximum engine power: , maximum horsepower: 82ps, maximum torque:

Body length, width and height: 3797*1510*1820mm. (Photo by photo:.)

Pacific Automobile Network Chen Yalan).

1. First of all, when adjusting the headlights, it is necessary to clarify the structure of the headlights, and Duan Youchu will take a look at the diagram of the headlights: it is to adjust the left and right sides of the high beam headlights, and the height of the high beam headlights is to adjust the height of the high beam headlights, and the left and right of the low beam headlights are high and low.

2. Adjust the left and right of the high beam headlights, there are two adjusting screws behind the headlights, one adjusts the height and the other adjusts the left and right, all of which control the low beam and high beam at the same time, which can be adjusted with a Phillips screwdriver, and the car is best adjusted close to the wall, so that it is easy to see the changes.

3. Adjust the height of the high beam headlights, for the adjustment of the distance and height of the headlights, there are corresponding adjustment screw knobs in the rear of the headlights, and the height or left and right of the lights can be adjusted separately.

It's easy! After turning on the knob of the headlight, push down the lever that hits the left and right turn signals, it is the high beam, and when you push it back, it is the low beam!

For more information, please visit the online car market.