Why do floor tiles arch over time?

Many people are willing to choose flooring when decorating, because the overall cost of flooring will be cheaper than pasting tiles, but this kind of flooring is only laminate flooring, not solid wood flooring. Therefore, after this kind of composite floor is used for a long time, due to thermal expansion and cold contraction, it will definitely cause arching.

Most of the tiles will not cause such factors, the reason for this is because many families have geothermal pipes laid underground, and the heat rises sharply in winter, because the quality of the plate is not enough, so it will swell, and it will shrink when it stops in the short termThis behavior is caused by the different stretches of the plates.

And I suggest that everyone, especially friends who have geothermal heating at home, it is best to make all the ground tiles, because the density of tiles is higher, so the service life can be longer.

The floor is really troublesome to clean in the later stage, especially the black substance in the cracks of the floor, which must be cleaned little by little with steel wool balls, and I didn't choose the floor well when I chose it, and there are a thin stripes on the surface of the floor. Therefore, when mopping the floor, it is impossible to remove all the dirt in those stripes.

If it is a tile, this will definitely not happen, and the marble tile will also look like it will enhance the overall grade of the house. Of course, there is another reason for this, that is, in the early stage of construction, there is no self-leveling, that is, the ground is not flat enough to cause such a factor. It is also possible that the ground has cracked during the early construction, so this crack is gradually getting bigger, making the ground bulge.

We have to consider whether the gap reserved for the floor tiles is too small, and the thermal expansion and contraction will lead to arching in the case of hot and cold staggering in winter and summer. There is also whether there is too little cement and sand when laying, and we should consider whether there are stones that have not been removed or tiles that have not been soaked in water when laying. Sometimes when buying tiles, you have to see if they are flat, otherwise they will be rumbling after a long time.

The most helpless one, when the house was first built, the foundation was not done, the wall sank, at this time, if you lift the bricks for maintenance, you will find that the surface has been covered with cracks, and the circle is covered! I'm sorry, but God can't guarantee your re-attaching tiles!

The house is subsided, although it is said that this possibility is very rare, but the respondent has encountered it. Once the main structure is damaged, all kinds of problems in home decoration will definitely follow.

If the craftsmanship is not up to par, masonry is a technical job that requires care and patience. When the cement mortar layer is not compacted, or the cement layer on the back of the tile is uneven, or the ratio of cement, sand and water is unreasonable, there will be a hollowing phenomenon, which greatly improves the possibility of tile arching.

Precautions and problem handling methods after tile paving.

Precautions: Before paving, the master is required to use the dry paving method to pave and place the seams with a seam card (the specific size of the gap is determined by himself). After paving, you must not be in a hurry to decorate, solidification is the king, sprinkle some water on the second or third day of paving, maintain it, pay attention to the sand leaking on the surface of the tile, and the scratches left by stepping on a grain of sand are not up to you after 5 years of use.

Then don't worry about protecting the canvas, and rest assured that you can decorate it after paving!

Floor tiles arch over time, and it is true that because of moisture, it will deform the floor and fall off the ground, and it will also cause the floor tiles to chip.

If the floor tiles have been arched for a long time, it is likely to be due to moisture, which can deform and crack the tiles.

The floor tiles are long and receive impacts, as well as ground clearances. And the influence of moisture is not great, because there is no sticking to the ground when laying.

With the tile itself, there are also certain reasons, if the temperature of the tile is not suitable, the temperature is too high will lead to the phenomenon of thermal expansion and contraction, so there will also be bulging, cracking. Therefore, this also warns people that in the process of decoration, they must not be greedy for cheap. When buying ceramic tiles, be sure to choose ceramic tiles with big brands, guaranteed quality and good water absorption.

In this way, there will be no unnecessary trouble.

The reason why the floor tiles arch for a long time is because of the improper paving method, and the structure of the building has been relatively changed; It is not necessarily caused by moisture, but also has something to do with construction problems, such as the reserved expansion joints are relatively narrow.

Floor tiles will arch up after a long period of use, generally because of staircase structure problems or improper construction, and rarely because of moisture.

Because the dampness will cause the phenomenon of arching of the floor tiles, you can re-apply the tiles, and then you must pay attention to maintenance and keep them dry.

Summary. Dear, the reason why the floor tiles will arch up for a long time:

Dear, the reason why the floor tiles will arch up for a long time:

The expansion ridge of the floor tile and the force generated by the contraction are not released, resulting in the arching of the floor tile. The force generated by the thermal expansion and contraction of the floor tiles, which eventually leads to the arching of the tiles, is the most fundamental reason for the age of the tile.

Extrinsic causes. The external reason is that the floor tiles are affected by the temperature and the heat generated by the nuclear collapse of the cold shrinkage shed. As we all know, if the floor tile is not subject to changes in external conditions, that is, if there is no change in temperature, it will not produce force.

The floor tiles will expand under the condition of returning or heating, and will shrink under the condition of cold leakage, so the external reason for the arching of the floor tiles is that the temperature of the floor tiles has changed. For example, the change of seasons, or the temperature of the floor heating leads to the change in the temperature of the floor tiles.

The stretch spacing reserved between tiles and tiles, tiles and surrounding walls is too narrow! When the room temperature changes severely, the floor, cement layer, and ceramic tile will all have thermal expansion and cold shaft phenomena. The spacing is too fine, the tiles lack the space to "stretch", the tiles are easy to become arched, which is easy to appear in the northern region, and the south has high humidity and small temperature difference, so it is not easy to appear.

When tiling, cement and sandstorms are not mixed in the right proportions. The cement label is low, the sandstorm is too much, and the time is long, and the cement downstairs cannot be attached to the floor tiles, and the tiles will become uneven. There is also a rare reason.

The original cement floor is very smooth, and tiles are laid without hair, which is prone to tile arching.

When part of the floor tiles of the house has arches, some can be removed directly, and some cannot. If you can't receive it, please don't just twist it and put it away. It's a bit of a hassle at this time.

To cut with a cutter along the edges. A tile has four sides, and how many sides to cut depends on the situation at the time. Cut it down, and after about an hour or two, the arched floor tiles will naturally fall.

Depending on the original position, try to re-paste to the original location and keep the original orientation of the tiles the same. Use a tool to scrape off the cement that sticks to the edge of the tile. After the mud on the original back is wiped clean with a rag, the back is smeared with the white adhesive of the carpenter, and the paste and compress one by one in the order of weaving.

The use of tile arrangement may cause arching. We know that there are two methods for the packaging of bricks, the dry packaging method and the wet packaging method, and the vast majority of residential decorations in the past have adopted the wet packaging method. There are drawbacks to the wet packaging method.

During the solidification of the cement, it absorbs most of the moisture in the sand, and over time, large areas of hollow and loose parts eventually become arches. In addition, it may be caused by structural problems in the building, and part of the mass will cause the pipeline building body to sink or move, resulting in the bottom of the building being squeezed or cracked. This situation is not a renovation project problem and cannot be **.

Or the end of the project protection is not suitable.

Many people are in a hurry when decorating, after the end of the bricklayer, the land is not too hard, move on it at will or carry out the construction of the next type of work, this behavior of people will lead to a decrease in the strength of cement mortar and a reduction in life. Tile arches can easily appear over time, which is the main reason for hollowing, loosening, and arching on the floor tiles. Second, tiles use smooth stickers.

Especially in the case of large spaces and long passages, the hot and cold tiles can produce hollows and arches. In the end, the master's technique cannot pass. So, how to solve and prevent it in advance?

In fact, most of the reason why tiles become arched is thermal expansion and cold contraction.

There are generally two reasons for this phenomenon, one is that there is a problem with the bottom floor when installing tiles, and there are certain problems with the spacing of tiles, and the other is that the indoor may be deformed due to moisture.

Answer: The force generated by the expansion and contraction of the floor tiles is not released, resulting in the arching of the floor tiles. The force generated by the thermal expansion and contraction of the floor tiles, which eventually leads to the arching of the tiles, is the most fundamental reason. For example, in the process of floor tiles expanding, it will generate an expansion force, and between these forces and forces, because they are not released, there will be floor tiles and floor tiles arching together.

The floor tiles swell together, and their expansive force acts together, and when the force is large to a certain extent, the floor tiles arch up.

Extrinsic causes. The external reason is that the floor tiles are affected by the temperature and the heat shrinks. As we all know, if the floor tile is not subject to changes in external conditions, that is, without any change in temperature, it will not produce force.

The floor tiles will expand under the condition of heating, and they will shrink when they are cold, so the external reason for the arching of the floor tiles is that the temperature of the floor tiles has changed. For example, the change of seasons, or the temperature of the floor heating leads to the change in the temperature of the floor tiles.

Reasons for the measure. The so-called reason for the measure is that the force generated by the temperature change of the floor tile cannot be released, that is, the measures we take are unreasonable. The most fundamental reason for this is that there are no gaps in the floor tiles when they are paved.

This gap is actually the gap that ensures the expansion and contraction of the floor tiles. However, when we lay the floor tiles, we used seamless paving, or the gaps in our floors were filled with cement mortar, which caused the gaps to fail. In these cases, in the process of expanding the floor tiles, there is no room for the force to be released, and finally the force is not released.

The cause of the floor tiles themselves. If it is a very dense floor tile, in fact, the amount of thermal expansion and contraction is very small. But if we buy some substandard floor tiles, such as some high water absorption floor tiles, then it produces a relatively large amount of expansion and contraction.

After this kind of floor tile is subject to temperature changes, coupled with the unreasonable retention of gaps, it is very easy to warp, and then there is a large area of cracking.

The hollow drum is large and loose, and will eventually arch up, and now basically the tiling is the dry paste method, and few people will use the wet paste method. In addition, it is possible that the building is causing structural problems in the body, but some quality experience builds the tube or solves the problem of walking around, causing the House to be squashed or ruptured.

It's because the inside of the home is too wet, and it's relatively unmanageable, so there will be such a phenomenon, and you should find a decoration company to maintain it.

Because the sand below is loose, the tiles of the floor arch up, and the decorator did not put the tiles in place when decorating.

This is because these decoration materials will warp up when heated, which also indicates that there is a serious problem with the quality of the product.

This is because the floor is most likely laminate flooring, and then thermal expansion and contraction.

If the stretching distance between the tiles and the tiles, or between the tiles and the surrounding walls, is too narrow, and when the room temperature changes, the tiles will expand in heat and shrink in cold. Therefore, the stretch space of the tile is small, and the tile is easy to arch.

This is a normal phenomenon. Don't pay special attention to it. This is caused by the narrow expansion gap reserved between the ceramic tile and the ceramic tile and the surrounding wall.

In addition, ceramic tiles have been laid for more than 20 years. When the room temperature changes sharply, the floor, cement layer and tiles will expand and contract with the heat and cold, which is easy to happen in the north and not easy to occur in the south due to high humidity and small temperature difference. Another possibility is that the mix of cement and yellow sand is not in the right ratio when laying tiles.

If the cement grade is low and the yellow sand is put too much, after a long time, the cement in the lower layer will not be able to stick to the floor tiles, resulting in the floor tiles being warped. The treatment method is: use a cutting machine to cut along the edge, directly remove the floor tiles piece by piece, and then use a tool to scrape off the cement that was originally glued to the edge of the tile.

Then apply it on the back with carpentry white glue, and then paste and compact it one by one in the order in which it has been prepared.

Avoid the occurrence of floor tiles in some places with cement slurry sticking to the ground, and some places with cement sand directly pasted, so that there will be hollowing, loosening and other phenomena in the short term, so when choosing a bricklayer master, you must see if his craftsmanship is not passable. And it is the main and most common reason for the arching of tiles. Because I remember very clearly, in the past, tiling really rarely deliberately left a seam, at most it was to leave a natural seam, so once it was a long time, it was easy to heat up and shrink and arch, because there was no room for expansion.

The gap left in the process of paving is too small, the gap is very small, but there is still mortar left in the gap, after thermal expansion and cold contraction, the corner of the tile is light and magnetic, and the heavy will be arched. After reaching a certain strength, the tile can be pressured, and if it is not completely dry, human trampling and other behaviors will lead to a decrease in the strength of the cement mortar and reduce the life. Over time, it is easy to have tiles arching.

The appearance of arching may be due to the fact that the cement slurry is not evenly made when laying, or it may be that the ratio of cement, sand and water is unreasonable. There is a relatively obvious gap between the cement slurry and the floor, and the floor will be prone to arching after a long time. Some masters also say that the brick is not soaked in water and does not wash the bottom of the reason, resulting in the separation of cement and brick bottom, the arch on the wall and the fall and fall of the wall and other reasons, the construction with tile glue is just a little sticky, and the shrinkage is even when solidifying.