How to write a report on cleaning the fume pipe

1. Artificial entry method: for parallel oil smoke pipes larger than 40 cm square, they can be manually drilled into for cleaning, this method is labor-intensive, and it is necessary to pay attention to strengthening ventilation and equipped with low-voltage (36 volts) lighting power supply.

2. Dismantling method: when the fume pipe is less than 40 cm square, this method is used when the manual can not enter, and the technical personnel disassemble a section of flue at certain distances to extend and clean up to both sides according to the actual situation of the site, this method has a good effect, is more difficult, and the cost is higher.

3. Hole opening method: This method adopts this method for the oil smoke pipeline that can not be entered manually and is difficult to disassemble, and the technician uses a special non-spark opening tool to open one or more sides of the pipeline, and the size, distance and quantity of the hole are determined according to the site conditions, and the pipeline is sealed and restored after the oil is cleaned.

4. Machinery and equipment cleaning method: This method is used to clean the fume pipeline with less oil pollution and short cleaning cycle, first spray the cleaning agent in the pipeline to soften the oil pollution, and then use a 30-meter-long electric flexible shaft brush to clean the oil stain.

This method is used in 30 cm square vertical flues, hidden small flues that cannot be accessed by humans and are inconvenient to disassemble. This kind of oil is not easy to clean and easy to accumulate oil, so the cleaning cycle should be shortened.

5. Airborne method: This method is mainly used to clean the vertical fume pipeline above 50 cm square, the technician first removes the upper and lower section of the pipeline, fixes the high-altitude safety rope above the fume pipeline, fastens the safety belt, and the technician cleans the oil stain in the vertical fume pipeline from top to bottom. This method is more dangerous, more technical, more expensive, and has a good cleaning effect.

Because the vertical oil smoke pipe generally accumulates less oil, it can be cleaned once a year.

Method 1: When the pipeline is larger than more than 40 cm, it can be manually drilled into for treatment, but this method is labor-intensive, easy to clean and not clean, and get stains on the body.

Method 2: Disassemble the pipe for cleaning. This method cleans more thoroughly and is more convenient, but the difficulty of this method is greater, and the distance of disassembly should be measured more accurately to ensure the quality of cleaning.

Method 3: In the fume pipe that cannot be entered manually and it is difficult to disassemble, you can use the method of opening holes, dig some small holes on the top of the fume pipe, clean the inside of the pipe through the small holes, and then seal each small hole.

Method 4: Soft brush assisted cleaning method, spray some detergent in the oil smoke pipe to soften the oil stain, and then use a long electric flexible shaft brush to stick detergent to clean the oil stain. This method is generally used for short erected range hood pipes, and concealed small pipes that cannot be accessed by humans and are difficult to disassemble.

With this cleaning method, it is easy to accumulate oil, so it is necessary to shorten the cleaning cycle.

Method 5: Use professional cleaning equipment to clean the kitchen fume pipe, with the continuous development and progress of science and technology, there is now a professional fume pipe cleaning equipment on the market, similar to the cleaning robot, but it may be the best and the cost is relatively high, and friends with conditions can choose this cleaning equipment.

Method 6: This method is mainly used to clean the vertical flue of more than 50 cm, because the technician needs to remove the top and bottom of the pipe first, and fix the high-altitude safety rope above the flue, tie the safety belt, and then clean the oil stain in the vertical flue from top to bottom. This method is very dangerous, more technical, and more expensive, but its cleaning effect is very good, because the vertical flue generally has less oil, so it can be cleaned once a year.

Hello! I am happy to answer your questions and give you a sample article, you can write an application like this, company leaders: When the equipment management office of the manufacturing technology department carries out the equipment relocation, in addition to the original equipment relocation plan, two sets of three-gear lines, 15 air switches, and two switch cabinet installation and commissioning work projects are added, which increases a lot of workload, but in order not to affect the company's production, the staff of our room use the pre-shift, post-shift, and week.

Sixth, Sunday rest time overtime surprise installation and commissioning, in 20xx x month x day into the installation and commissioning of the equipment successfully completed the installation and commissioning work, in order to stimulate the enthusiasm of our staff, now apply for the company to give rewards. It is hereby reported to the Equipment Management Office of the Manufacturing Technology Department Applicant: 20xx/x/x.

1. The staff should change into work clothes, wear protective glasses and masks, and fasten seat belts. Imitation defeat.

2. a standpipe. 1) First make the preliminary preparations for the construction of the lower riser, and the construction personnel must only have the qualification of high-altitude operation, fasten the safety belt, and wear a safety helmet with a top light. In addition, it is equipped with an air pressure pump to prepare the construction personnel to keep the air flowing in the vertical pipe.

2) After all the preparations are ready, the construction personnel enter the vertical chan pipe to shovel the oil on the pipe wall, shovel the oil and then use a strong degreaser to clean the oil on the pipe wall, to the bottom of the vertical pipe, the construction personnel will receive the remaining garbage together with the shovel oil barrel, and then the roof construction personnel with a safety rope to the roof, and put the garbage into the garbage bag for inspection.

3. a transverse pipe. 1) Set up a ladder.

2) Two workers go up the ladder in turn, the workers put the 36v low-voltage lamp into the pipeline, and put the garbage bin of liquid oil into the pipeline.

3) After entering the pipeline, first use a shovel to clean the oil inside the pipeline, put it into the garbage can, and then wipe the inside of the pipeline with a medicant, and then take the garbage can out of the pipeline.

4) After the construction is completed, the pipeline is reset with raw materials, and the pipeline is sealed, restored to the original state, and the safety measures of the construction personnel are done.

Mesh cleaning: Remove the grille first, soak it in medicated water, then rinse it with a high-pressure cleaner, and then press it back.

Cover cleaning: first use a shovel to clean the oil on the surface of the cover, then rinse it with a high-pressure cleaner, and then install it back as it is, and do the surface curing.

After the construction of the project is completed, the cleaning personnel will clean up the site and pull the oil and other garbage out of the company.

Thoroughly remove oil from kitchen pipes to prevent fires.

1.Prepare tools and materials: detergent, brushes, gloves, masks, rags, buckets, etc.

2.Close the range hood and gas valves, and remove the oil mesh and oil cup of the range hood. 3.

Remove the air inlet and outlet of the fume pipe, and clean the inside of the pipe with a brush. 4.Pour the cleaner into a bucket of water, dip the brush into the cleaner, start at the air inlet, and brush along the pipe.

5.After brushing, rinse the inside of the pipe with clean water until the water runs out cleanly. 6.

Wipe the inside and outside of the pipe with a rag and reinstall the pipe. 7.After cleaning, clean the oil mesh and the crude oil cup and reinstall it on the oil worm smoke machine.

8.Open the gas valve and range hood to test whether the range hood is working properly. 9.

After cleaning, clean the tools and materials of the stuffy stool to keep it clean and hygienic.

The cleaning process of the oil fume pipeline is: preparing to clean the belt supplies, installing the pipeline cleaning equipment, preparing before cleaning, cleaning, and maintaining the cleaned pipeline.

1. Prepare cleaning supplies.

It is best to use a special cleaning agent for cleaning supplies. Cleaning agents come in different grades, from extremely corrosive to mild. Choosing a milder cleaner can show concern for the environment and protection of the equipment.

Also prepare tools such as gloves, protective mask, brushes, cleaning cloths, etc.

2. Install pipeline cleaning equipment.

Before proceeding with cleaning, pipe cleaning equipment is first installed. This can be done by taking over the air intake into the fume duct. The equipment should be able to spray the inside of the pipe with cleaning agent and the amount of cleaning agent sprayed can be controlled.

3. Preparation before cleaning.

Pipes must be inspected before cleaning work can be carried out. Special inspection tools, such as video cameras or thermal imaging cameras, can be used to check for grease and grime build-up. If there is, you can use a professional slag vacuum cleaner or pusher to gently clean it.

4. Clean.

The method of cleaning is to spray a mild cleaning agent on the inside of the pipe. Use safety precautions such as gloves and a face shield when using cleaning agents. Spray the cleaner on top of the pipe to ensure that the spray is even. Wait for some time before rinsing with water.

5. Maintain the cleaned pipeline.

After cleaning, make sure the pipes are dry. Because damp pipes will attract dust and dirt more easily, etc. Next, you can spray the surface of the pipe with a preservative. The use of preservatives can extend the life of the pipe.

The process of cleaning the oil fume pipe. It is broken down into the following steps:

1.First, clean up the solid substances such as carbon deposits and dirt in the oil smoke pipe.

2.Tools such as high-pressure water guns are fed into the pipes to completely remove grease, dirt, and bacteria from the pipes.

3.Use professional cleaning agents and equipment to disinfect the inside of the pipes and kill bacteria.

4.Conduct a water discharge test to ensure that the effluent in the pipe can pass smoothly.

5.Carry out anti-corrosion treatment of pipelines to prevent secondary pollution. The above is the basic process of cleaning the fume pipe, which can effectively ensure the hygiene of the kitchen type and prevent the harm of the fume to the human body. Shut up.