How to disassemble and clean the oil fume purifier?

No matter which brand of oil fume purifier needs to be cleaned and maintained regularly, so how to disassemble and clean the oil fume purifier? The following will explain to you the detailed methods and steps of disassembling the oil fume purifier, so that you can help when cleaning the oil fume purifier. The following are the steps to disassemble the oil fume purifier:

1. Open the electrical compartment door, the general manufacturer will be equipped with the electrical compartment door key, after opening the electrical compartment door, you can see the internal power supply and protection switch, at this time you need to close the protection switch first. 2. Remove the wiring on the binding post, unscrew the knob cap of the electric field bin door, open the bin door to see the electric field, and remove the spring on it before pulling out the electric field.

3. After the electric field is slowly withdrawn, the air nets on both sides are removed, and the fume purifier is basically disassembled, and the fume purifier can be repaired or cleaned.

1. Prepare tools: high-pressure water gun, cleaning tools, needle adjuster, wooden sticks, rubber gloves, screwdrivers, protective glasses, caustic soda, cleaning tank, corrector;

2. Open the centralized control box, cut off the power supply, and the power indicator is off;

3. Use the metal part of an insulating screwdriver to release the residual charge in the electric field;

4. extracting the electric field component;

5. Heating caustic soda with hot water in the cleaning tank with a weight ratio of 1:25;

6. Soak the electric field component in a caustic soda solution above 80 degrees;

7. After about 20 minutes of soaking in the electric field, the oil stain of Dali floats to the surface of the solution;

8. After the soaking is completed, use a tool to take out the electric field component from the solution;

9. When the fouling of individual cylinders is serious, cleaning tools can be used to remove debris and oil stains;

10. The electric field after soaking and washing is fully sprayed with a high-pressure water gun;

11. Rinse the clean electric field in a clean place, and then wipe the four supporting cathode plus porcelain bottles with a cloth;

12. The corrector detects the position of each cathode needle;

13. Detect whether the anode cylinder has a concave part, and if there is, use a round wooden rod to slowly restore it;

14. extracting the porous air equalizing net;

15. Put the porous air homogenization net into the human caustic soda solution and soak it thoroughly;

16. Soak and wash for about 5 minutes, and then use a tool to take out the porous air mesh from the solution;

17. Use a high-pressure water gun to flush the porous air net on the front and back;

18. Rinse the cleaned electric field components and air leveling nets in a clean place to dry;

19. Put the electric field without thimble into the body first;

20. Then put the electric field of the thimble, pay attention to the direction of the thimble inward, and ensure that the high-voltage thimble is in contact with the electric field;

21. Pay attention to the direction of the thimble inward to ensure that the high-voltage thimble is in contact with the electric field;

22. installing a porous air sizing net;

23. First use caustic soda to clean the dirt on the core-piercing porcelain bottle, and then wash the lye attached to the surface with water;

24. Open the centralized control box, turn on the power supply, and the power indicator light will be on.

If the fume purifier is not cleaned for half a year, it will cause the flue path to be blocked, so that the fume will produce unqualified emissions, and seriously damage the living environment of human beings. Dr. Qi Environmental teaches you how to clean the fume purifier.

The range hood filter is an important part of the range hood and is the key factor to ensure the normal operation of the range hood. During daily use, cooking fumes will be sucked into the filter, resulting in filter blockage, grease accumulation, affecting the ventilation effect and filtration effect of the range hood, and it needs to be cleaned in time.

The following describes how to disassemble and clean the range hood filter:

Step 1: Turn off the power of the range hood and turn off the gas or power for cooking.

Step 2: Open the lattice of the range hood and remove the noise filter.

Step 3: Use a brush or cooking oil cloth to clean the grease build-up on the surface of the filter.

Step 4: Then put the strainer in warm water, add an appropriate amount of detergent or laundry detergent, and soak for a while.

Step 5: Slowly brush the net with a soft brush, especially the grid structure, and clean it well with a brush, because the grease is deposited in the small pores of the net, which should be cleaned for a better filtration effect.

Step 6: Rinse the filter with water and rinse repeatedly until there is no grease on the screen.

Step 7: After drying, insert the filter back into the hood.

It should be noted that the cleaning filter can not be scraped with a knife or scrubbed with a hard object, because the filter is usually made of aluminum alloy or stainless steel, and scraping with a hard object will damage the lattice network structure, affect the effect of filtration, and will also make the surface of the filter easier to adhere to oil smoke stains.

In short, regular cleaning of range hood filters is of great help to ensure home air safety and reduce indoor oil smoke pollution. At the same time, regular cleaning of the filter can also extend the service life of the range hood, so that the range hood in our home will always be in good working condition, making our life more comfortable and healthy.

The kitchen fumes are heavy, and it is necessary to install a fume purifier. Next, I will talk to you about how to disassemble and wash the oil fume purifier and how to maintain the oil fume purifier.

1. How to disassemble and wash the oil fume purifier.

Step 1: Turn off the power.

Before cleaning the fume purifier, be sure to turn off the power supply first and drain the charge in it. Don't think that if you don't turn off the power, it won't affect your safety, otherwise you will regret it if it is dangerous and affects your health. After turning off the power, it is also necessary to use a screwdriver to touch the cathode and anode of the electric field and discharge the charge.

Step 2: Unscrew the bolt and pull out the electric field.

When the power supply has been disconnected, unscrew the bolts for fixing, open the maintenance door, and then pull both sides of the electric field by hand, and hold the end with your hand when the electric field is about to be withdrawn to prevent it from falling off suddenly and damaging the electric field.

Step 3: Disassemble the accessories for easy cleaning.

Some parts of the purifier should be removed, especially the insulator, because the insulator is easy to be damaged after being wet, and in addition, the leakage insulator is also convenient for the cleaning of other accessories, such as the cathode needle and anode cylinder.

Step 4: Electric field cleaning, soaking and rinsing.

The cleaning tank accompanies the container, and the shape of the appliance used is larger than the shape of the electric field. When cleaning the reeds, it is best to move the purifier to the toilet to avoid direct contamination of the floor by oil stains. Cleaning can be scrubbed with a mixture of caustic soda and hot water, plus a high-pressure water gun with water, and the rinsing time is determined according to the oil stain.

Remember to dry in the sun after washing.

Step 5: Inspection and cleaning of insulators.

The oil stain on the surface of the insulator should be cleaned, and the cleaning method is to spray alcohol on the insulator first, and then wipe it dry with a dry rag.

Second, how to maintain the fume purifier.

1. The electric field of the oil fume purifier uses a cylindrical honeycomb structure, which greatly improves the effect of removing oil fumes, and the electric field damage should be avoided as much as possible when in use.

2. The cylindrical honeycomb electric field has good rigidity and is easy to disassemble and assemble, pay attention to reinstalling it in the original way during daily cleaning, and do not make a mistake, so as not to affect the normal use of the fume purifier.

3. The noise of the oil fume purifier is low during operation, but if the internal parts are damaged, the noise will become louder, at this time, it is best to find a professional to check it.

4. The oil fume purifier has a high safety factor and low radiation, so pay attention to cleaning and maintenance when using it, and remember to cut off the power supply when not in use.

5. The purification efficiency of the oil fume purifier is high, but after a long time, there is a lot of dirt left on the filter screen, and the purification effect will be reduced.

If the fume purifier is used for a long time, there will be a lot of dirt on the surface and inside, and if it is not cleaned in time, the temperature will be too high and cause a fire. The above is the dismantling and cleaning method and maintenance method of the oil fume purifier, I hope it will help you.

The cleaning of the environmental protection range hood is very critical to maintain a good use effect and prolong the service life, and only regular cleaning and maintenance of the environmental protection range hood can ensure its normal operation. The following is the disassembly and cleaning method of the environmentally friendly range hood:

1. Before preparing tools to disassemble the environmental protection hood, you need to prepare the tools you need. Commonly used tools are wrenches, Phillips screwdrivers, combs, cleaning agents, etc.

Second, to disassemble the range hood first, you need to turn off the power supply, turn off the power switch on the electrical board, to avoid power loss due to misoperation. Then which is right, remove the cover of the environmental protection range hood, usually there will be some inner stiffeners on the hood hood, and use a Phillips screwdriver to loosen the positioning screws up and down. After the cover is removed, the fan is removed and connected to the power supply of the old part of the outer cherry tree, so it needs to be removed and cleaned thoroughly.

3. There will be a large amount of oil stains fixed on the dismantled shell and internal screws of the range hood, which need to be slowly brushed with a comb, and at the same time use cleaning agent to clean the inside of the range hood, especially the surface, and the complex contour can be cleaned with a special brush. Be sure not to soak the range hood in water when cleaning to avoid damaging the parts.

Fourth, after the installation of the range hood is cleaned, all parts need to be cleaned, the parts are dragged dry, and the water is completely removed. When assembling again, it should be noted that a layer of lubricating oil needs to be evenly applied to the screw buckle used during assembly, which is easy to attract dust and reduce the service life of the product.

The above is the disassembly and cleaning method of the environmental protection range hood. It is difficult to clean the environmental protection range hood, so it is recommended to clean it regularly, deal with the internal grease of the range hood in time, and maintain the range hood regularly to ensure its long-term and effective use.

Range hood disassembly and cleaning method, in fact, each brand of range hood disassembly and cleaning method is different, it is best to refer to the manual to prompt the operation. Alternatively, you can ask a professional to help you disassemble and wash it. Let's take a look at the common dismantling and washing methods:

1. Unplug the power supply of the range hood and disassemble the parts of the range hood.

2. Soak each spare part in a container filled with soda ash water, and scrape off and clean the place where the oil is particularly thick.

3. Clean with range hood degreaser.

Let's take a look at the specific cleaning steps:

1. Prepare to spray the range hood cleaning agent, and spray the prepared range hood cleaning agent on the range hood, but at this time, it can not only spray the panel, but also spray the inside of the iron grille, and spray it in every place where there may be oil stains, but this is done to let the dirty oil accumulated in the range hood fully dilute into liquid and flow out.

2. Turn on the range hood, spray the cleaning agent for about 5 to 8 minutes, you can start the range hood, it starts the range hood is to let the dirty oil in the range hood flow out, but generally speaking, we wait for the oil to flow to the place where our hands can touch, but this is better to clean, and it will be cleaner.

3. Prepare a basin of boiling water soaked in laundry detergent, boil the boiling water, pour it into the basin, and then pour in the strong laundry detergent prepared in advance.

4. Oil stains on the cleaning panel of the range hood, but you can first use a rag to scrub the panel of the range hood for a simple scrubbing, after a simple scrubbing, then put the rag into the basin of water with washing powder prepared in advance, and then scrub and scrub a few more times.

When professionals come to operate, on the one hand, they will detect the current use status of the range hood, including whether there are potential failures, etc., if it is used normally, they will find the screws installed on the range hood, and the inside of the range hood can be cleaned well after the screws are opened. This is also the reason why it is not recommended to disassemble the range hood by yourself, because once a certain part fails, the subsequent operation of the whole machine will have a big problem.

During the process of disassembling the hood, they will be very careful to avoid its motor part or turbine part coming into contact with the exterior. Because the motor of the range hood is often only dust, not oil, once contaminated with oil, it may lead to subsequent practical use problems, you can also suggest professional cleaning personnel, first clean the appearance, and then open the inside of the range hood to avoid cross-contamination. After that, follow the disassembly steps and put it back on.

How to disassemble and clean the side-draft range hood; 1.The structure of the side-draft range hood is simple, the overall structure has no dead angles, and the cleaning is also simple. The first is the part that needs to be cleaned.

The general cleaning parts are the body and blade fan of the range hood, the oil net and the oil storage box. Cleaning the fuselage is relatively straightforward. You only need to wipe the body with a damp rag dipped in dish soap, and wipe the oil and stains with a rag after wiping them.

2.Next is the fan. When cleaning the fan blades of the range hood, a range fume purifier is generally used.

Cover the hood and table with newspaper and spray the fumes onto the fan blades. After waiting for a few minutes, turn on the hood and use the centrifugal force of the fan to remove the oil stains. Clean the fan blades of the range hood.

Cover the hood and the table with newspaper, spray the "smoke net" onto the fan blades, wait for a few minutes, turn on the range hood, and use the centrifugal force of the fan to remove the oil stains. 3.Remove the oil net with a screwdriver, then spray the "clean oil smoke" on the oil net, put the oil net sprayed with "clean oil smoke" into a plastic bag, take it out after a quarter of an hour, and then put it into about 80 hot water, and wipe it clean with a rag.

When cleaning a side-draft range hood, the easiest place to clean is the oil reservoir. When you see that there is oil in it, you can take it off and wash it. 4.

After cleaning, it is the oil storage box. In the cleaning of side-draft range hoods, the place that is easy to clean is the oil storage box. If you see that there is oil in it, you can take it off and clean it.

If it is more troublesome to clean too often, you can also put a plastic wrap on the box, so that it can be replaced regularly, saving the trouble of cleaning. 5.When cleaning the leaf fan, pay attention to unscrew the screws of the cover plate and mesh cover, and remove the cover plate and mesh cover.

Then unscrew the fastening screws of the wind wheel and take out the wind wheel. Soak the removed parts in warm water containing degreaser and wipe with a soft, clean water cloth. Scrub the dirt in the volute cavity with a soft cloth dipped in a small amount of warm water containing degreasing agent, and wipe it with a soft water rag; Install the above parts in the reverse order of disassembly; After installation, check whether the oil circuit of the appliance is unobstructed and whether the sealing ring on the volute can be sealed; Please clean the wind wheel, volute, grease nozzle, and oil drain pipe according to the range hood maintenance cycle.