It s all Core 2 processors, what s the difference between T5 T7 T8? I see a lot of them with similar

The performance index frequency is one, but also depends on the manufacturing process (65nm, 45nm), L2 cache and front-end bus.

The main frequency of the series is currently from to, the front-end bus is 667 to 800, and the L2 cache is 2M.

The main frequency of the T7 series is above the main frequency, the front-end bus is more than 800, the L2 cache is more than 2M, and the T5 and T7 are all using 65nm technology.

The T8 series uses 45nm technology, which has strong performance, low heat generation and more power saving. The other indices are similar to T7.

The main frequency T5, T7, T8 will increase sequentially, and the key L2 cache will also increase in turn.

Generally, the T5 is equipped with mid-range products, while the products with T7 and T8 are relatively high-end.

Notebook Core 2 processors have T, P, X several ways to start (and L, which belongs to the low-voltage type, uncommon) Their performance is generally increased in turn, of which X is a cutting-edge notebook, which is also rare.

Mainly look at t, p, in the case of the same letter at the beginning, the larger the next first digit, the better the performance, such as t7 is stronger than t5.

In the case of the above situation being the same, the higher the second digit, the better the performance, for example, the T5400 is stronger than the T5200.

This is a naming rule, and my language expression skills are not good, so I don't know if I can understand it.

The higher, the better.

The main frequency is definitely getting higher and higher.

It's just that the main frequency value doesn't seem to have much difference.

But in fact, when it comes to practical use.

The CPU gap is barely felt.

Just don't go too low.

T8 is advanced, T8 is 45nm process, T7 is 65nm process.

The heat dissipation of the T8 is much better than that of the T7.

This is like asking which of the two 100 on the ground I pick up, I personally prefer the figure, but everything can not be extreme, compared to the extreme of lifting ants, I accept the mean.

hollaback girl by gwen stefani

one of us

the show-lenka

Personally, I think it's pretty good.

The background of the advertisement** is this (-I can't remember what advertisement).

It's also very good, listen to it a few times, and you'll almost be able to sing.

Must DJ? But it's not necessarily the best DJ! So let's introduce you to a few songs.

Various Artists - Trouble is a Friend (DJ with a personal rating of 95).

Golden Years DJ Edition (If necessary, you can choose the accelerated DJ version Personal evaluation 75 points).

Well- -I don't think there are enough more than 3 songs. But I don't listen to DJs much, I just like to listen to songs that are more like DJ rhythms.

Dear, if liked.

It is not recommended to use plug-ins to play games,During this time,Due to the 55 open event,Check the plug-in is very strict,And the plug-in update is very fast,It's very likely that you get the old version.,The old version is basically sealed in seconds.。

Hope. Accurate aurate

Just exactly

Just right

There is no relationship between whether the compressor is good or bad and the appearance and shape of the compressor.

The external dimensions of the compressor are related to the design capacity of the compressor, and the compressor with a relatively large number of horses cannot be designed to be round, and most of them are elongated.

Only compressors with a small number of horsepower will be designed to be round.

The wire mouth of 1 4 refers to the thread of 6mm.

Generally, it refers to the connection method of pipes and pipe fittings, and the commonly used methods are divided into: silk mouth and Fazheng buried orchid. The wire mouth is the thread screwed in; The flange is to weld the two pipe ends connected to the boss ring and drill a few holes, and insert bolts into the holes for connection.

"Wire mouth flange" is a combination of the two ways, is a separate connection method, that is, the pipe flange threaded connection, the flange is not welded at the pipe end, but with the thread to connect with the pipe end.

5750：

L2 Cache (KB) Dual-core shared 2048

Front-side bus frequency (MHz) 667

Voltage around.

Multi** instruction sets mmx, sse, sse2, sse3, sses38100:

L2 Cache (KB) Dual-core shared 3072

FSB frequency (MHz) 800

Voltage is the highest.

Multi-** instruction set mmx, sse, sse2, sse3, SSE3, in fact, it seems that the difference is quite big, and the time of use is about the same.

It's just that the 8100 is a little faster than the 5750, and you can feel it when making animations, and the other differences are not much.

The front-end bus and the L2 cache are different, T5 has a frequency greater than T7, T7 has a frequency greater than T8, and T8 is a 45nm process, which has lower power consumption, while the first two are 65nm process, T8 and T7 are better than T5 and T5 are better than T2 in overall performance. This is especially true in terms of calorific value, with T8 and T7 operating at much lower temperatures than T5 and T2. This will help a lot in the battery life.

Under the same conditions, the difference between T8100 and T5750 should not be too big.