How to turn on the microcomputer step by step water boiling machine

Step-by-step water boiler, as the name suggests, is an energy-saving water boiling equipment that is heated layer by layer by layer from the bottom inlet water, and gradually heated until the water is boiled. It can improve the separation of hot and cold water and ensure a healthy boiling water, alleviate the degree of "yin and yang water", and the electric energy control ensures that it boils only once, so as to completely avoid repeated heating; After 1 liter of water is heated and boiled, 1 liter of water is heated from the bottom until the water tank is full, and the step-by-step water boiler can continuously discharge boiling water, avoiding the waiting time of the traditional water boiler before the whole tank of water can be boiled; The traditional water boiler relies on steam expansion to discharge water from the heating box to the incubator, which is equivalent to countless boilings; The step-by-step water boiler relies on electrodes to measure the temperature, the temperature control is accurate, and the outlet water temperature is constant at 96-99 degrees; Electronic leakage protection alarm function, electronic temperature control to prevent dry burning without water, and anti-overflow and leakage function.

Fast. Navigation.

Features: Technical principles, advantages, precautions.

Definition. Step-by-step water boiler, as the name suggests, is an energy-saving water boiling device that replenishes water at the bottom and heats it gradually until the water is boiled.

It is a subversive revolution to the traditional water boiler. The use of water inlet at the bottom avoids the serious problem of "yin and yang water" caused by the "violent" inlet of the upper layer of water and the raw water immediately mixing into the whole tank of hot water. Relying on the low temperature of the raw water, the specific gravity sinks to the bottom, which alleviates the mixing problem.

If it is combined with a horizontal separator, the effect can be further improved, but due to factors such as water fluctuations and molecular diffusion, raw water cannot be guaranteed to be completely mixed with the upper cooked water. To a considerable extent, the water boiler that improves the separation of hot and cold water and ensures a healthy boiling, produces less "yin and yang water", and the electric energy control ensures that it only boils once, so as to completely avoid repeated heating; After heating and boiling 1 liter of water, heat 1 liter of water from the bottom until the water tank is full, and the boiling water can be continuously discharged, avoiding the waiting time for the water to be taken after the whole tank of water in the traditional water boiler is boiled;

Method Steps:

1.Reasons for failure of step-by-step water boiler not entering water 1The water valve is not open or the water is stopped 2The timer switch does not have a power-on state 3The connecting wire of the solenoid valve is not connected properly 4The solenoid valve is clogged or burned out 5The control water inlet switch fails.

2.The solution of the electric water boiler does not enter the water 1Open the water valve or check the water source 2Check whether the power on and off time is in the power-on state 3Check if the solenoid valve is well connected 4Clean the solenoid valve or replace 5Replace the control board.

What is the reason why the microcomputer step-by-step water boiler does not enter the water 1Heating method: 100% disposable pure boiled water is heated layer by layer, and the machine has its own water purifier inside to make the boiled water healthier.

2.When the faucet is opened, it is boiling water, not that the boiling water cannot be released, and the separation of cold and hot water is fully realized, and the computer controls the temperature to ensure that it boils only once. 3.

The first boiling time is 7-15 minutes. After the first time the water is boiled, it can be taken and taken as it is, without interruption, without waiting, saving time. 4.

Microcomputer control: automatic detection of water cut-off, overflow, abnormal water inlet and fault, the machine comes with a timing on/off function, digital temperature display.

Dear, according to your description, there may be the following reasons why the micro good branch computer commercial stepping water boiler does not turn on the socks and socks:1Power supply failure:

Check whether the socket and plug are normal, whether the plug is plugged tightly, whether the socket has electricity and other factors. You can also use an electric pen or multimeter to check if the socket has power. 2.

Fuse failure: Check whether there is a fuse inside the water boiler, whether it is burned out, and if there is a problem, it needs to be replaced. 3.

Circuit problems: Faulty circuit boards or switches will cause the water boiler to not turn on or not work, and if there is a problem, it needs to be repaired or replaced. 4.

Poor contact: The water boiler can automatically power off to prevent the water boiler from short circuiting, but if the line is not in good contact, it may also cause it to not work. 5.

Overheating protection: After the water boiler works for a period of time, if the water level is found to be extremely low or the switch is faulty, the power supply will be automatically cut off to prevent it from burning out. If the above methods do not work, it is recommended that you contact the manufacturer for repair to avoid irreversible damage caused by self-modification.

1. First of all, check whether the power switch is in the "on" state; 2. Check the reset resistor on the motherboard to see if there is any open circuit; 3. Check whether the power supply and wires are in poor contact or open circuit; 4. Check whether the BIOS battery is aged or scrapped; 5. Check whether the microcomputer controller is faulty as the main control chip, and sometimes there is a problem with the microprocessor, which is related to the main control chip; 6. Check whether the radiator falls off and whether the radiator seat is not correctly fixed on the motherboard; 7. Check whether there is a problem with the internal circuit of the motherboard; 8. If it weren't for the above reasons, you could try to reinstall the microprocessor in Anheheng; In addition, attention should be paid to the temperature, humidity and air circulation of the microcomputer-controlled water boiler environment. If the environmental requirements are not met, it is easy to cause the circuit board to burn out, which may affect the normal operation of the main control chip, and then lead to the failure to boot. In addition, it is necessary to regularly replace electronic components such as electrical vertical containers, switches, and transistors on the motherboard to ensure that they work properly.

1.Check whether the power supply is normal: Use a professional instrument to check whether the input voltage of the power supply meets the requirements of the electrical appliance.

2.Check whether the dismantling switch is operating normally: disassemble the large switch of the electrical appliance, check whether the contacts are loose and coarse, and if it is loose, it can be removed and reconnected.

3.Check the MCU: Remove the MCU, connect the power supply and reset signals with a clamp (pen), and press the reset button to observe whether the MCU works normally.

4.Check whether the driver is normal: Remove the driver, connect the power supply with a clamp (pen), and check whether each output is normal (symmetrical output).

5.Check whether the temperature sensor is working properly: take a picture of the temperature sensor to observe whether there are serious aging symptoms, and replace it if the aging is too severe.

Hello dear, please check the following aspects:1Check whether the water source is normal, check whether the water pipe is blocked, and clean up the stuck objects of the water pipe; 2.

Check whether the water pipe inside the machine is in place, check whether the water pipe is leaking, if so, please replace it in time; 3.Check whether the water source valve is blocked, and if so, clean it up in time; 4.Check whether the silver and land connections at the connection of the water pipe are connected, and if not, please connect them in time; 5.

Check whether the pressure of the water pipe is normal, if the pressure is too low, please adjust the water pressure; 6.Check whether the water pipe is blocked, check whether the machine control panel is faulty, and if so, replace it in time.

Hello dear, I have the answer to your question:1Check the water pipes for damage or blockage, and if so, replace the Danxin water pipes; 2.

Check whether the water level setter of the water boiler is adjusted correctly, if the module wheel is incorrect, please adjust the water level that should be discharged; 3.Check if the water valve of the water boiler is closed, and if it is, please open the water valve; 4.Check whether the power supply and control circuit are normal, if not, please replace the new control circuit; 5.

Check whether there is water in the water tank of the water boiler, if there is no water, **water; 6.Check whether the pump is normal, if not, replace it with a new one; 7.Check if the filter of the water pump is clogged, and if it is clogged, clean or replace it with a new one.

How to install the step-by-step microelectric Rangkai brain electric water boiler According to my understanding, 1. Take out the product and check whether the accessories are kept intact; 2. Place the products and accessories in an open and suitable installation place, and the water boiler must be placed smoothly; 3. When connecting water and electricity, you should pay attention to check whether the water is leaking, and whether the electricity connection is firm, safe and reliable. 4. The connector must be equipped with a leakage switch, and the specification of the leakage switch shall not be less than 40A. I hope mine helps you.

Be.