Q810g Little Swan washing machine spinning speed is slow and weak, what is the reason?

Q810G Little Swan washing machine dehydration speed slow, weak reasons and treatment methods:

First, when the washing machine is washing clothes, if the motor has a humming sound, but does not turn, it may be a problem with the starting capacitor. If there is no sound from the motor, it may be that the lid linkage switch of the dehydration bucket is faulty.

Second, check whether the belt is loose, check the pawl and clutch, and see if the brake is tight or whether the mechanism plate on the drum cover is broken.

Third, the automatic washing machine does not rotate, some motors with clutches are very hot, and the starting capacitor may be broken, or the wire head falls off and the motor cannot be started. If there is no clutch, see if the motor is stuck, do not idle the belt under the motor experiment, whether it is stuck, if it is not stuck, most of the starting capacitors are problematic.

Fourth, the spinning tube does not rotate in the following situations:

1. The motor burns out (no reflection when energized).

2. The brake line is broken (the motor cannot be started after the power is turned on).

3. The timer is damaged (after twisting and twisting, the timer has no ticking sound).

4. The water seal is damaged (the water seal is damaged, and it is difficult to put the clothes right until the official does not turn, and the sound of the clothes tube can be heard at this time).

5. The line is open (generally visible with the eye).

Maybe the motor is damaged, maybe something is tripping, or maybe the motor is going to break.

The capacitor capacity of the point machine is insufficient

If the dehydration speed of the drum washing machine is too slow, it may be because the drainage pipe is blocked, it may be because the water level switch cannot be reset, or it may be because the electrical socket is loose, and it is more likely that there are too many dehydrated clothes.

The solution to the slow spinning speed of the Little Swan drum washing machine is as follows:

1. Dehydration caused by drainage pipe blockage, if the speed is too slow, what should be done is to get the blockage problem of the drainage pipeline, you can first clean the items blocked by the drainage pipe, when the washing liquid in the sinking pipe or test tube is too much, there is no way to drain it, it will not be able to dehydrate normally.

2. The water level switch can not be reset will also cause the washing machine to dehydrate too slowly, the washing machine will remove the washing liquid clean, its water level switch can be located, if the dehydration circuit can not be connected at this time, there is naturally no way to dehydrate, what should be done is to reset the water level switch.

3. The spinning speed of the drum washing machine is too slow, you can also see if the socket of the electrical appliance is loose, if it is loose, it will not be able to continue to supply power in the process of transportation, and there will be no way to continue to rotate, it is likely that the electrical socket is loose due to vibration, and it can be fixed.

4. Too many dehydrated clothes will also cause the drum washing machine to spin too slowly, because some clothes are too heavy to operate, and there may be stuck, indicating what should be done, is to turn on the drum washing machine and spin it in stages.

1. Caused by capacitance change or failure.

The washing machine spins off the barrel slowly, and the weakness is generally caused by the change or failure of the capacitor. Try to change to the same capacitor, but remember that the capacity of the capacitor should not exceed the original value, if it is too large, it is easy to heat up the motor, or even burn out, and if it is too small, the speed is not enough.

In addition, if the line has a broken circuit, there will also be this problem, at this time, the capacitor does not work, it is better to check whether the line and capacitor are in good condition, if it is confirmed that the capacitor is broken, and then buy a capacitor to replace it, so as not to waste.

2. The brake on the motor of the dry bucket is not released.

Remove the rear cover and open the door cover of the dry bucket, observe whether the brake will correspond to the action and loosen, if the brake is not loosened, check whether the cable connected to the door cover is too loose or disconnected, adjust or connect the cable, so that the brake can be loosened when the door cover is opened.

3. The motor coupling is damaged.

Excluding the reason that the brake is not loosened, it may be that the motor bearing is still difficult to rotate the motor coupling because of the lack of oil, damage or burning of the windings (it is recommended to find a professional repair).

4. Poor contact of the door cover safety switch.

Excluding the reason that the brake is not loosened and the motor is damaged, it may be that the motor rotates freely when opening the door cover, and the power is still not turning, and the problem is that the door cover safety switch is in poor contact or there is a phenomenon of rat biting the broken wire (after disassembling the washing machine, the upper three screws and opening the operation panel cover to check, and shorting the two wires of the door cover switch to test the machine).

5. The variable capacity of the capacitor of the spin-off motor is insufficient.

If it does not rotate, it is suspected that the capacitor of the spin-off motor is variable and the capacity is insufficient, and the capacitor test machine of the same specification should be replaced to solve the problem; If it does not turn, the motor winding is burned, so it is recommended to find professional maintenance.

Summary. 1. Unbalanced clothing.

When the washing cannot be adjusted to balance, the washing machine automatically sets a low speed, at which the dehydration effect is slightly worse. The switch of the top cover is damaged, and the washing machine is not allowed to open the top cover because it is a high-speed action when it is dehydrated, so there is a linkage switch on the top cover, which will be automatically disconnected as soon as the cover circuit is opened. If it is damaged and dehydrated, it will not move!

2. The drainage system is blocked.

The washing liquid in the water cylinder can not be discharged, or there is too much foam in the water cylinder, the washing liquid in the cylinder is difficult to drain for a while, the water level switch cannot be reset, and the washing machine cannot enter the dehydration program.

3. The water level switch cannot be reset.

The washing machine dehydration process starts with the water level switch reset after the washing liquid has been drained. If the drain level switch is damaged, dewatering is a procedure that needs to be carried out after draining, and if the water level switch is damaged, you will not be able to enter the dewatering program! Open the back cover of the washing machine and move the pulley by hand, and there should be no jamming.

After the power is turned on, the motor has a humming sound and does not rotate, which means that the motor is short-circuited or damaged between turns, or the capacitor is not connected to the motor circuit. At this time, the power supply should be cut off, and the motor belt should be removed and restarted. If the motor still does not rotate or the speed is low, it is a motor failure and should be repaired.

What is the reason why the Little Swan washing machine does not spin at high speed.

1. When the laundry is unbalanced, the washing machine will automatically set a low dust opening speed, and the dehydration effect will be slightly worse at this speed. The switch of the top cover is damaged, and the washing machine is not allowed to open the top cover because it is a high-speed action when it is dehydrated, so there is a linkage switch on the top cover, which will be automatically disconnected as soon as the cover circuit is opened. If it is damaged and dehydrated, it will not move!

2. The drainage system is blocked and the washing liquid in the water cylinder cannot be discharged, or there is too much foam in the water cylinder, and the washing liquid in the cylinder is difficult to drain for a while, the spring chan water level switch cannot be reset, and the washing machine cannot enter the dehydration program. 3. The water level switch cannot be reset, and the dehydration procedure of the washing machine starts under the condition that the water level switch is reset after the washing liquid is discharged. If the drain level switch is damaged, dewatering is a procedure that needs to be carried out after draining, and if the water level switch is damaged, you will not be able to enter the dewatering program!

Open the back cover of the washing machine and move the pulley by hand, and there should be no jamming. After the power is turned on, the motor has a humming sound and does not rotate, which means that the motor is short-circuited or damaged between turns, or the capacitor is not connected to the motor circuit. At this time, the power supply should be cut off, and the motor belt should be removed and restarted.

If the motor still does not rotate or the speed is low, it is a motor failure and should be repaired.

Pro: All of these reasons can cause the washing machine to not work.

And then there's the fact that your washing machine is washing too many clothes and not being in the appropriate gear.

Less than seven kilograms of the aircraft load.

Is that gear also set to the corresponding gear?

What gear? water intake.

Make the highest water level.

Or maybe the fuse inside is burned out.

You take some clothes out and try to see if it works.

I can run it. Is the washing machine working?

See if there is a problem with the motor, and then see if the transmission belt is loose, and you can test the tension if you have the conditions!

Perhaps it is the reduction in the capacitance capacity of the motor. There is no force. Laundry is normal because it doesn't take much effort to do it.

All of the above are possible, and there is also the problem of clutch adjustment, that is, the clutch is slippery, and there is a screw adjustable.

The belt is loose. Adjust the belt if it is not broken. If it's broken, change it!

The washing machine takes off the water for 2 seconds, and the water enters the water, what is the problem.

Check whether the capacitor has become smaller, or if the motor rotor bearing is corroded. It affects the speed of the motor, and makes the dehydration speed unable to rise.

Check to see if there is too much laundry in the dehydration bucket. If there is not too much, it may be a problem with the shaft of the motor.

When dehydration is too slow, first check whether the belt is collected.

It may be that the washing machine has more than the rated capacity to wash clothes at a time, resulting in a decrease in the speed of the washing machine, and it is necessary to reduce the amount of clothes and dehydrate again; It may be that the transmission belt of the washing machine is aging and loose, and it needs to be replaced with a new belt; It may be that the fixing nut between the washing machine motor and the connecting shaft of the dehydration bucket is loose and causes the roller sleeve to slip and cannot drive the dehydration bucket, and the nut needs to be retightened and then dehydrated. The details are as follows:

1. Check whether there are too many clothes washed at a time, exceeding the rated capacity, and only need to take out some clothes to solve the problem;

2. Check whether the belt is aging and loose, try to solve it by adjusting the distance between the motor and the rotating shaft, or replace the new belt;

3. Check whether the capacitance of the capacitor has become smaller due to poor quality or too long use, and try to replace the new capacitor with the same capacity;

4. Check whether the washing machine is damaged, the spring will not be tight after a long time, resulting in the inner barrel not rotating when dehydration, and the nut of the clutch total belt disc can be removed and replaced after removing the belt;

5. Check whether the fixing nut of the connecting shaft between the motor and the dehydration bucket is loose, causing the shaft sleeve to slip and the spinning bucket will not move, try to tighten the nut and try again.

1. If there are too many clothes washed at a time, which exceeds the rated capacity, only need to take out some clothes to solve the problem;

2. The belt is aging and loose, try to solve it by adjusting the distance between the motor and the rotating shaft, or replace the new belt;

3. The capacitance of the capacitor becomes smaller due to poor quality or too long use, try to replace the new capacitor with the same capacity;

4. The washing machine is damaged, and the spring will not be tightly held after a long time, resulting in the inner barrel not rotating during dehydration.

5. The fixing nut of the shaft connecting the motor and the dehydration bucket is loose, causing the shaft sleeve to slip and not move the dehydration bucket, try to tighten the nut and try again.

It is recommended to report for repair professional after-sales personnel to come to the door for maintenance, hoping to help you.

The clothes inside the fuselage are in an unbalanced state, the drain pipe is in the wrong position, the drainage system is blocked, the water level switch is malfunctioning, the top switch is damaged, the drain solenoid is faulty, the washing machine cover is not covered, the dehydration process is converted to rinsing, overheating protection, clothing material problems, computer control board failure, etc. 1.When the laundry cannot be adjusted to balance, the washing machine will automatically set a low speed, and the dehydration effect will be slightly worse at this speed.

Drum washing machine.

Dear, thank you for your patience, after inquiry: the slow speed of the Little Swan washing machine is not dehydrated is the reason may be: the clothes inside the fuselage are in an unbalanced hail and rotten beam state, the drainage pipe is in the wrong position, the drainage system is blocked, the water level switch is faulty, the top switch is damaged, the drainage electromagnet suction is faulty, the washing machine cover is not covered, the dehydration process is transformed into rinsing, overheating protection, clothing material problems, computer control board failure, etc.

1.When the laundry cannot be adjusted to balance, the washing machine will automatically set a low speed, and the dehydration effect will be slightly worse at this speed.

2.The location of the drainage pipe is wrongWhen installing, if the lead infiltration of the drainage pipe is high, it is easy to have no dehydration when draining, and it is difficult to drain normally. 3.

If the drainage system is blocked, if the drainage pipe is blocked, the washing machine may not be dehydrated.