Why can t the door open after the little swan rolls and pokes the washing machine after it is dehydr

It will take 2 minutes to open the door, don't worry.

There are two types of this:

1. Just start dehydration.

This phenomenon is normal, and every washing machine is like this. Because there is a lot of moisture on the clothes at the beginning of spinning, if it starts at high speed, the inner barrel of the washing machine will shake very much, and it may touch the safety switch of the washing machine, so that the washing machine will think that the clothes in the inner bucket are eccentric, and will be washed with new water, so it is necessary to turn and stop 3 to 4 times before starting to spin drying.

2. This situation for a long time.

If you maintain the state of rotation and stop for a long time, it may be that the belt is loose, resulting in no power in the washing machine, in this case, you can call a technician to check it, there are many reasons for the lack of washing power.

1. Little swan.

There is a problem with the washing machine's capacitance, resulting in the output power.

If it is insufficient, it can be solved by replacing the capacitor. 2. The computer curing program of the Little Swan washing machine is damaged, and the washing machine cannot enter the dehydration program. In this case, the panel can only be replaced.

3. It may be that the solenoid valve is damaged and the dehydration cannot operate normally, the drain valve does not open the conversion of the Lihuai attendant, and the washing and dewatering of the automatic washing machine is completed by the gear at the bottom of the solenoid valve, and the damage of the solenoid valve will also make the dehydration unable to operate normally. 4. The poor performance of the motor of the Little Swan washing machine leads to the inability to dehydrate the lead. Suggested workaround:

1. Test whether the empty barrel of the Little Swan washing machine can be dehydrated, if so, it means that the fastening screws of the inner barrel of the Little Swan washing machine are loose, or the bottom bracket of the inner barrel of the washing machine is damaged, and the corresponding parts can be replaced directly. 2. If the drainage system of the Little Swan washing machine is blocked or the drain valve is broken, the washing liquid in the water cylinder cannot be discharged, the washing liquid in the cylinder is difficult to drain for a while, the water level switch cannot be reset in time, and the washing machine cannot enter the dehydration program. It is recommended to wait for a while after shutting down and then restarting.

3. This requires a new solenoid valve, which can be bought at a special store. If the above methods still can't solve the problem, then you need to ask a professional maintenance master to come to the door for maintenance.

Fully automatic washing machines either do not dehydrate or dehydrate and do not dry:

Possible causes and solutions: the speed is less than 800 rpm (drum washing machine), the belt is too loose, and the motor is burned. Front-loading washing machines generally require more than 800 rpm to spin and dry.

If the problem is not solved, it may be that the motor is burned, and the only way to rotate is to replace the motor or repair the motor. However, the reason for this kind of failure phenomenon is generally that the belt is too loose.

When dehydrating, even if there is no clothing in it, it has to go through 6-7 intermittent start-stop dehydration because the starting torque is large when it just enters the dehydration, in order to protect the motor and control circuit from being damaged by excessive current, so it can only be designed to use intermittent start instead of one-time start, so your washing machine is normal.

The washing machine should be the most frequently used household appliances in the home, and even can be used every day, many families use the Little Swan automatic washing machine, but occasionally because of improper use or long time will cause dehydration and dry results. When we encounter this achievement, we will think that the washing machine is broken, should be replaced, in fact, there are many reasons why the Little Swan automatic washing machine is dehydrated and does not dry, we should be the first to search for the reason, the ability to adopt the correct way to deal with it.

Little Swan Washing Machine is the largest washing machine brand in the world, and is the world's third largest laundry system manufacturer. Little Swan washing machine has been ranked first in the country for 13 consecutive years, Little Swan washing machine has excellent technology, put forward "water saving under high washing rate" In terms of washing rate, Little Swan washing machine water cube "free of embrace" at the same time to place multiple groups of water flow to pull together, improve the strength of water flow, effectively reduce the wear rate of clothes up to 35%. In terms of water saving, the Little Swan washing machine uses the independent "dynamic technology water-saving function" and the "fully biased closed non-porous stainless steel inner cylinder" to wash out the result of seven points of water, and the water saving rate is as high as 30%.

The reason why the little swan washing machine is dehydrated and does not dry :

1) Whether the clothes are seriously biased to the side of the dehydration bucket, or the laundry is placed too much and the dehydration bucket cannot be operated.

2) The plug of the closed-door switch is poor, and whether the connectors and wires can be --- can be used in ordinary times is greater.

3) Check whether there are foreign objects between the dehydration bucket and the water bucket.

4) If the V-belt is too loose or sparse, the belt can be adjusted or replaced.

5) The large oil seal is not installed properly and jams the dehydration shaft. (Generally, it is easy to occur after replacing the large oil seal during maintenance).

6) The brake band is not loosened.

7) Program control board deviation. *If there is a deviation of the water level switch or water level sensor (or the air leakage of the trachea adjacent to it), it is not possible to reflect the information that has been discharged to the computer to perform the next dehydration work, it is recommended to change the water level switch or water level sensor first, and do not forget to check the air leakage results of the adjacent trachea.

8) Can the amount of clothing be too small, because it is summer, one or two clothes are also released to wash, and the result is that it is not balanced. Add a little more laundry to the location to be able to intervene in the dehydration method. The balance of the drum washing machine is important to the following two pressure reducers, the most important thing is to wear and tear for a long time and lack of oil, shock absorption is not flexible, and it is not enough to dehydrate, please change the pressure reducer when necessary.

When encountering these achievements, we must treat them with specific results, and when we are not able to deal with them ourselves, we must play the after-sales service of the Little Swan washing machine and let professionals repair it. Of course, the after-sales service of the Little Swan washing machine is still good.

That is, the author introduced the reason why the automatic washing machine is dehydrated and not dry, we must use the washing machine reasonably, and when the use of the time is long, we will also replace the parts in time. If you wish, you will save the trouble that you don't need. In general, when encountering this result, it is necessary to clean the cause in time and repair it at the turn of the year.

Read the original article.

Washing machine can not be dehydrated troubleshooting:

1. The washing is in an unbalanced state during washing.

1) When there are too many clothes, the washing can not be adjusted to the balance, the washing machine will automatically adjust to low speed, resulting in poor dehydration effect, if it is caused by this reason, then the boy does not have to worry.

2) Before washing clothes, put the number of clothes less, do not stuff too much at once, so as not to cause imbalance during washing, thus affecting the dehydration effect.

2. The safety switch is damaged.

1) If the safety switch of the top cover of the washing machine is damaged, the washing machine belongs to the mechanical movement of high-speed operation in the process of dehydration, so try not to open the top cover during the dehydration process, so as not to cause damage to the top linkage switch.

2) If the top cover linkage switch of the washing machine is damaged, the washing machine cannot be dehydrated, so do not forcibly open the top cover during the dehydration process.

3. The drainage system of the washing machine is blocked.

1) When the drainage system of the washing machine is blocked, the washing liquid in the water cylinder will not be discharged; When there is too much foam in the water cylinder, or the washing liquid in the cylinder is difficult to drain for a while, the water level switch cannot be reset, and the washing machine cannot enter the dehydration program.

2) If the washing machine cannot be dehydrated due to this reason, it is recommended to remove the drain filter and clean it first, rinse the drain with water, and remove the debris in the drain valve.

4. The water level switch cannot be reset.

The washing machine dehydration process starts with the water level switch reset after the washing liquid has been drained. If the drain level switch is damaged, dewatering is a procedure that needs to be carried out after draining, and if the water level switch is damaged, the dewatering procedure will not be entered.

5. The washing machine cannot be dehydrated due to motor failure.

You can try opening the back cover of the washing machine and moving the pulley by hand if there is no jamming. After the power is turned on, the motor has a humming sound and does not rotate, which means that the motor is short-circuited or damaged between turns, or the capacitor is not connected to the motor circuit.

At this time, the power supply should be cut off, and the motor belt should be removed and restarted. If the motor still does not rotate or the speed is low, it is a motor failure, and the motor should be repaired or replaced.

Summary. Hello, kiss the little swan drum washing machine, can't get rid of the water! I can't spin it off at high speed!

Reason 1: Unbalanced clothesWhen the detergent cannot be adjusted to balance, the washing machine will automatically set a low speed, and the dehydration effect is slightly worse. Reason 2:

The top cover switch is damaged when the washing machine is dehydrated, due to the high speed driving, the top cover is not allowed to be opened, so there is a linkage switch on the top cover, and the circuit will be automatically disconnected as soon as the cover is opened. If it's damaged and dehydrated, it won't move! Reason three:

The texture of the clothes is recommended to be dehydrated at a high rate (some high-end clothes cannot be dehydrated at a high speed). Reason 4: Clogged drainage system.

The washing liquid in the water pipe cannot be discharged, or there is too much foam in the water pipe, the washing liquid in the water pipe is difficult to discharge, the water level switch cannot be reset, and the washing machine cannot enter the dehydration program.

Little Swan drum washing machine, can't get rid of water! I can't spin it off at high speed!

Hello, kiss the little swan drum washing machine, can't get rid of the water! I can't spin it off at high speed! Reason 1:

When the detergent cannot be adjusted to the balance, the washing machine will automatically set a low speed, and the dehydration effect is slightly worse. Reason 2: The top cover switch damages the washing machine when it is dehydrated, due to the high speed driving, the top cover is not allowed to be opened, so there is a linkage switch on the top cover, and the cover circuit will be automatically disconnected as soon as the cover is opened.

If it's damaged and dehydrated, it won't be a sell! Reason 3: The texture of the clothes is recommended to be dehydrated at high speed (some high-end clothes cannot be dehydrated at high speed).

Reason 4: The drainage system is clogged. The washing liquid in the water pipe cannot be discharged, or there is too much foam in the water pipe, the washing liquid in the water pipe is difficult to discharge, the water level switch cannot be reset, and the washing machine cannot enter the dehydration program.

Reason 5: The water level switch cannot be reset, and the dehydration procedure of the washing machine starts from the reset of the water level switch after the washing liquid is cleaned. If the drain level switch is damaged, dewatering is required after draining.

If the water level switch is damaged, you can't enter the dehydration program! Open the back cover of the washing machine's pin and move the pulley by hand so that it does not get stuck. If the motor hums but does not rotate after the power is turned on, the motor is short-circuited or damaged between turns, or the capacitor is not connected to the motor circuit.

At this time, the power supply should be cut off, and the motor belt should be removed to restart. If the motor still does not rotate or is at low speed, it is a motor failure and the motor should be repaired or replaced. The cleaning and dewatering of the automatic washing machine is done by converting the gear at the bottom of the solenoid valve, and the damage of the solenoid valve will also make the dehydration unable to operate normally!

Reason 5: The motor plug is loose due to the fact that the drum washing machine connection wire adopts a connector, and during transportation, due to vibration and other reasons, the motor plug is often loose or ejected during installation. If the plug is loose, it should be reinserted and tied tightly with a strapping cord to prevent it from falling off again.