How to use gas wall hung boiler correctly to achieve safe heating?

1. Do not touch the wall-hung boiler in operation, and pay attention to anti-freezing.

During the operation of the gas wall-hung boiler, a certain amount of heat will be generated, and the mechanism in operation will have a certain temperature, and the smoke pipe and hot water outlet pipe of the wall-hung boiler will be relatively hot, and we cannot touch it during use to avoid damage.

In addition, the low temperature and cold in winter, if the wall-hung boiler does not operate for a long time, it is easy to be frozen, we need to make relevant anti-freezing preparations and maintain the "three-way" state, that is: water, electricity, and gas, so as to avoid the heating system, the water pump of the gas wall-hung boiler, the heat exchanger and other internal parts from freezing and damage, affecting the normal use of the wall-hung boiler.

2. Keep the smoke pipe of the wall-hung furnace unobstructed and not blocked.

The gas wall-hung boiler usually uses a double-core tube, which is divided into an inner and outer tube, the outer tube sucks in fresh air, and the inner tube discharges exhaust gas, and the two-way operation needs to be kept unobstructed. During the installation process, we must extend the suction and discharge of the smoke pipe of the wall-hung furnace out of the outside, and cannot be closed indoors, or use a single-core tube. Otherwise, it is easy to cause the exhaust gas generated by the wall-hung boiler to be sucked back during the combustion process, and the oxygen supply will be unsuccessful, which will lead to frequent start and stop of the wall-hung boiler, ignition and other situations, and even leave certain safety hazards.

3. Clean the gas wall-hung boiler regularly and do a good job of cleaning and maintenance.

After long-term operation, the integration of water, electricity and gas will produce scale and carbon deposits, and the sediment of the pipeline will affect the use of the wall-hung boiler, so in order to ensure the normal service life of the gas wall-hung boiler, it is necessary to do a good job of cleaning and maintenance on a regular basis, and at the same time, it will also save the use of gas to a certain extent, which is also a way to save energy.

Fourth, the small flow of water to open the gas wall-hung boiler.

Saving water resources is a concept that society has always advocated, and we should start from our daily lives. When using a wall-hung boiler, in addition to saving gas, you should not waste water. When we start the gas wall-hung boiler, we can start with a small flow of water, because at first the water temperature has not yet arrived, there is a delay of a few seconds, so as to minimize the waste of water resources.

It is necessary to use the ** manual before use, and there should be some detailed steps for specific use in the manual.

The connection is made by means of a pipe and an adhesive inside, which is not visible from the outside at all, and it is also highly ornamental.

The hot water produced by the wall-hung boiler flows out from the outlet end of the wall-hung boiler and transports the water to the inlet of each radiator through the water separator, and then flows out from the outlet of the radiator, gathers the dispersed water through the water collector, and transports the hot water with reduced temperature into the wall-hung boiler for heating, and the heated hot water flows out from the water outlet again, and so on and so on.

If you want to connect it well, the whole corresponding system and function should be connected together, and it is necessary to produce this kind of intelligent feeling to achieve very good results.

How to use the heating gas wall-hung boiler:

1. Water injection. Just install the gas wall-hung boiler made of Qianyan first inject water, the water injection method is to open the exhaust valve first, and then open the water supply valve of the wall-hung boiler for water replenishment, after the water filling pressure is reached, please be sure to close the water supply valve, otherwise, the system overpressure pressure relief valve will always leak, may soak the indoor items; Then observe whether there is water flowing out of the exhaust hole of the exhaust valve, if there is water flowing out, it means that the system water has been filled, and the exhaust valve can be closed.

2. Power on. Turn on the power switch of all gas wall-hung boilers, let the wall-hung boilers turn on the power supply and start working, it should be noted that the wall-hung boilers use leakage protection plugs, and press the on/off key in the middle to turn on the power.

3. Run. The operation here refers to the trial operation, let the gas wall-hung boiler run by itself for 5 minutes, and then start the ignition after the air in the system is almost exhausted and the water pressure of the system is stable.

4. Temperature setting.

There are two kinds of gas wall-hung boilers, one is single-function, which can only be heated by Huiheng, and the other is a wall-hung boiler that integrates heating and bathing. If it is a dual-function function, it is necessary to set the temperature for the two, if it is a radiator heating, the set temperature is 80 degrees, and if it is a floor heating, the temperature is set to 60 degrees.

The set temperature of the domestic hot water part is best not higher than 50 degrees, the first operation of the Anerrui gas wall-hung boiler due to the cold water temperature, please do not set the temperature too high, too high water temperature is easy to make the wall-hung boiler run for a long time and can not reach the set temperature.

1. When the ignition switch of the wall-hung boiler enters the working state, the fan starts first to form a negative pressure difference in the combustion chamber, and the wind pressure switch sends the command to the water pump, and after the pump starts, the water flow switch sends the command to the high-pressure discharger, and the command is sent to the gas proportional valve, and the gas proportional valve starts to start.

2. Due to the existence of negative pressure in the combustion chamber, there is no aggregation and combustion phenomenon of natural gas beam leakage, so that there will be no deflagration phenomenon in the rubber quiet, so as to achieve calm ignition and ultra-quiet, and also avoid the occurrence of dangerous accidents, this standard can identify the stability of the furnace.

3. Some people are worried about gas safety because they don't understand the operation control principle of the gas proportional valve of the wall-hung boiler. When the flue gas induction switch does not detect the exhaust gas discharge in 5 seconds, the gas proportional valve will be cut off to stop the gas supply, and the gas proportional valve will be operated to ensure the safe use of gas.